ALASTRIA Red T

Visit What is alastria page to know more about us.

This page contains technical information needed to work in the Alastria ecosystem on the possible different ways.

You'll need at least a host/node to interact with the network, please read the technical requirements for it.

System requirements

Operating System: Ubuntu 16.04 64 bits; Ubuntu 18.04 64 bits

Hardware:

Hardware	minimum	desired
CPU's:	2	4
Memory:	4 Gb	8 Gb
Hard Disk:	100 Gb	1000 Gb

Important Requirement

A DNS resolver must be available and accessible to make the installation process possible.

E.g. the command

dig +short netstats.telsius.alastria.io @resolver1.opendns.com

must yield a valid, routable IPv4 address

TCP/UDP PORTS

You'll need to open the following ports in your firewall, inbound and outbound to deploy a node:

Port	Type	Definition
21000	TCP/UDP	Geth process application port (inbound and outbound for ethereum traffic)
9000	TCP	Constellation port (private transactions, inbound and outbound)
80	TCP	Outbound for Websockets feed to netstats server
80 and 443	TCP	Inbound RPC Port if using the automatic installation with Alastria Open Access Component
8086	TCP	Outbound for InfluxDB statistics collection
53	TCP/UDP	Access to external Internet based resolvers

IP ADDRESSES

The IP resulting out of the installation process (e.g. the IPv4 part of the enode) , must not be an RFC1918 IPv4 address

10.0.0.0/8 172.16.0.0/12 192.168.0.0/16

These IP addresses are non-routable and will result in your node being unreachable and unable to participate in the blockchain.

In case the installation process yields a non-routable IP address, you must verify if your node is behind a firewall, in which case you might use the firewall's external address only in the case the firewall provides for Full-cone NAT.

Restricted-Cone NAT has not been tested yet for p2p functionality.

Installation & configuration of

[Regular node] Quorum node + Constellation + Access point + Monitor

(English) Installation Guide
(Spanish) Installation Guide
Repository of the access-point that comes installed inside the docker of the regular node Access-point

[Regular node] Quorum node installation using Ansible from host machine

(English) Installation Guide

[Validator node] Quorum node + Access point + Monitor

[Bootnode node] Quorum node

Deployment of Smart Contracts on Alastria Network

To know more about the use of Alastria Network, you can visit the Smart Contract Deployment Guides:

Deploying to Alastria's network T (Quorum), created by Roberto Garcia, from Lleida University
Deploying to Alastria's Red T using Remix & Metamask created by Jose María del Molino, from AYESA
Deploying to Alastria's Red T using Truffle (Quorum) created by Guillermo Araujo, from Babel

(IMPORTANT) Be aware that the actual's Alastria network EVM version is byzantium and , therefore, the Smart Contracts must be compiled for this EVM's versión:

Remix:

Truffle: in truffle.js configuration file

compilers: {
    solc: {
      version: "0.5.17", // A version or constraint - Ex. "^0.5.0"
      settings: {
        optimizer: {
          enabled: true,
          runs: 100   // Optimize for how many times you intend to run the code
        },
        evmVersion: "byzantium" // for T network
      }
    }
  }

Buidler: in buidler.config.ts configuration file

const config: BuidlerConfig = {
  solc: {
    version: '0.5.17',
    evmVersion: 'byzantium',
    optimizer: {
      enabled: true,
      runs: 100
    }
  },

Connection from External Applications using WebSockets

Connecting to an Alastria's Red T node using WebSockets created by Ronny Demera, from Tribalyte

Checking Node's Health

In order to check if your node is operational, you can establish monitoring based on your node's ingress and egress P2P traffic during the last 5 minutes.

As soon as the node comes up, e.g. starts to run, it will send metrics points to Alastria InfluxDB server.

These are queries to the InfluxDB API you can translate into your preferred language and/or framework:

Ingress traffic:

curl -G 'http://geth-metrics.planisys.net:8086/query?pretty=true' --data-urlencode "db=alastria" --data-urlencode "user=EDITED_USER" --data-urlencode "password=EDITED_PASSWORD" --data-urlencode "q=select mean(m1) from \"geth.p2p/InboundTraffic.meter\" where (time > now()-5m AND host =~ /^REG_YOUR_NODE_NAME$/)"

Egress traffic:

curl -G 'http://geth-metrics.planisys.net:8086/query?pretty=true' --data-urlencode "db=alastria" --data-urlencode "user=EDITED_USER" --data-urlencode "password=EDITED_PASSWORD" --data-urlencode "q=select mean(m1) from \"geth.p2p/OutboundTraffic.meter\" where (time > now()-5m AND host =~ /^REG_YOUR_NODE_NAME$/)"

The output are jsons that need to parsed and look like this (value is a pair where the second field should be > 0)

{
    "results": [
        {
            "statement_id": 0,
            "series": [
                {
                    "name": "geth.p2p/OutboundTraffic.meter",
                    "columns": [
                        "time",
                        "mean"
                    ],
                    "values": [
                        [
                            "2020-06-15T08:40:12.772770668Z",
                            1225.7697298713392
                        ]
                    ]
                }
            ]
        }
    ]
}

Alastria network resources

List of links with resources for the Alastria Network

WIKI
- Home
- F.A.Q.
Resources
¿Need Help?
- Slack
- Github (use & governance)

jcarovestigia/alastria-node