ESP32_TFT_library: A C repository from jeremyjh

Not Maintained

I'm not currently doing any ESP32 development at all, and so I'm unable to address issues in this library. If anyone will volunteer to maintain the active fork I'm happy to link to it from this README. Just open a PR with the README changes.

For my own project I ended up using LVGL instead of this library.

The license of this project is in complete doubt because upstream never released it under an open source license.

Technically it is not open source and no one can use it in their project without risk of a copyright infringement, though loboris clearly intended for people to use it freely.

TFT library for ESP32

This library must be built with the esp-idf release/v4.0 branch.

ESP-IDF 4.0 is currently in beta and instructions are found here

Features

Full support for ILI9341, ILI9488, ST7789V and ST7735 based TFT modules in 4-wire SPI mode.
18-bit (RGB) color mode used
SPI displays oriented SPI driver library based on spi-master driver
Combined DMA SPI transfer mode and direct SPI for maximal speed
Grayscale mode can be selected during runtime which converts all colors to gray scale
SPI speeds up to 40 MHz are tested and work without problems
Demo application included which demonstrates most of the library features
Graphics drawing functions:
- TFT_drawPixel Draw pixel at given x,y coordinates
- TFT_drawLine Draw line between two points
- TFT_drawFastVLine, TFT_drawFastHLine Draw vertical or horizontal line of given length
- TFT_drawLineByAngle Draw line on screen from (x,y) point at given angle
- TFT_drawRect, TFT_fillRect Draw rectangle on screen or fill given rectangular screen region with color
- TFT_drawRoundRect, TFT_fillRoundRect Draw rectangle on screen or fill given rectangular screen region with color with rounded corners
- TFT_drawCircle, TFT_fillCircle Draw or fill circle on screen
- TFT_drawEllipse, TFT_fillEllipse Draw or fill ellipse on screen
- TFT_drawTriangle, TFT_fillTriangle Draw or fill triangle on screen
- TFT_drawArc Draw circle arc on screen, from ~ to given angles, with given thickness. Can be outlined with different color
- TFT_drawPolygon Draw polygon on screen with given number of sides (3~60). Can be outlined with different color and rotated by given angle
Fonts:
- fixed width and proportional fonts are supported; 8 fonts embedded
- unlimited number of fonts from file
- 7-segment vector font with variable width/height is included (only numbers and few characters)
- Proportional fonts can be used in fixed width mode
- Related functions:
  - TFT_setFont Set current font from one of embeded fonts or font file
  - TFT_getfontsize Returns current font height & width in pixels
  - TFT_getfontheight Returns current font height in pixels
  - set_7seg_font_atrib Set attributes for 7 segment vector font
  - getFontCharacters Get all font's characters to buffer
String write function:
- TFT_print Write text to display
  - Strings can be printed at any angle. Rotation of the displayed text depends on tft_font_rotate variable (0~360)
  - if font_transparent variable is set to 1, no background pixels will be printed
  - If the text does not fit the screen/window width it will be clipped ( if text_wrap=0 ), or continued on next line ( if text_wrap=1 )
  - Two special characters are allowed in strings: \r CR (0x0D), clears the display to EOL, \n LF (ox0A), continues to the new line, x=0
  - Special values can be entered for X position:
    - CENTER centers the text
    - RIGHT right justifies the text horizontaly
    - LASTX continues from last X position; offset can be used: LASTX+n
  - Special values can be entered for Y:
    - CENTER centers the text verticaly
    - BOTTOM bottom justifies the text
    - LASTY continues from last Y position; offset can be used: LASTY+n
- TFT_getStringWidth Returns the string width in pixels based on current font characteristics. Useful for positioning strings on the screen
- TFT_clearStringRect Fills the rectangle occupied by string with current background color
Images:
- TFT_jpg_image Decodes and displays JPEG images
  - Limits:
    - Baseline only. Progressive and Lossless JPEG format are not supported
    - Image size: Up to 65520 x 65520 pixels
    - Color space: YCbCr three components only. Gray scale image is not supported
    - Sampling factor: 4:4:4, 4:2:2 or 4:2:0
  - Can display the image from file or memory buffer
  - Image can be scaled by factor 0 ~ 3 (1/1, 1/2, 1/4 or 1/8)
  - Image is displayed from X,Y position on screen/window:
    - X: image left position; constants CENTER & RIGHT can be used; negative value is accepted
    - Y: image top position; constants CENTER & BOTTOM can be used; negative value is accepted
- TFT_bmp_image Decodes and displays BMP images
  - Only uncompressed RGB 24-bit with no color space information BMP images can be displayed
  - Can display the image from file or memory buffer
  - Image can be scaled by factor 0 ~ 7; if scale>0, image is scaled by factor 1/(scale+1)
  - Image is displayed from X,Y position on screen/window:
    - X: image left position; constants CENTER & RIGHT can be used; negative value is accepted
    - Y: image top position; constants CENTER & BOTTOM can be used; negative value is accepted
Window functions:
- Drawing on screen can be limited to rectangular window, smaller than the full display dimensions
- When defined, all graphics, text and image coordinates are translated to window coordinates
- Related functions
  - TFT_setclipwin Sets the window area coordinates
  - TFT_resetclipwin Reset the window to full screen dimensions
  - TFT_saveClipWin Save current window to temporary variable
  - TFT_restoreClipWin Restore current window from temporary variable
  - TFT_fillWindow Fill window area with color
Touch screen supported (for now only XPT2046 controllers)
- TFT_read_touch Detect if touched and return X,Y coordinates. Raw touch screen or calibrated values can be returned.
  - calibrated coordinates are adjusted for screen orientation
Read from display memory supported
- TFT_readPixel Read pixel color value from display GRAM at given x,y coordinates
- TFT_readData Read color data from rectangular screen area
Other display functions:
- TFT_fillScreen Fill the whole screen with color
- TFT_setRotation Set screen rotation; PORTRAIT, PORTRAIT_FLIP, LANDSCAPE and LANDSCAPE_FLIP are supported
- TFT_invertDisplay Set inverted/normal colors
- TFT_compare_colors Compare two color structures
- disp_select() Activate display's CS line
- disp_deselect() Deactivate display's CS line
- find_rd_speed() Find maximum spi clock for successful read from display RAM
- TFT_display_init() Perform display initialization sequence. Sets orientation to landscape; clears the screen. SPI interface must already be set up, tft_disp_type, tft_width, tft_height variables must be set.
- HSBtoRGB Converts the components of a color, as specified by the HSB model to an equivalent set of values for the default RGB model
- TFT_setGammaCurve() Select one of 4 Gamma curves
compile_font_file Function which compiles font c source file to font file which can be used in TFT_setFont() function to select external font. Created file have the same name as source file and extension .fnt
Global variables
- tft_orientation current screen orientation
- tft_font_rotate current font rotate angle (0~395)
- tft_font_transparent if not 0 draw fonts transparent
- tft_font_forceFixed if not zero force drawing proportional fonts with fixed width
- tft_text_wrap if not 0 wrap long text to the new line, else clip
- tft_fg current foreground color for fonts
- tft_bg current background for non transparent fonts
- tft_dispWin current display clip window
- tft_angleOffset angle offset for arc, polygon and line by angle functions
- tft_image_debug print debug messages during image decode if set to 1
- tft_cfont Currently used font structure
- tft_x X position of the next character after TFT_print() function
- tft_y Y position of the next character after TFT_print() function
- tft_tp_calx touch screen X calibration constant
- tft_tp_caly touch screen Y calibration constant
- tft_gray_scale convert all colors to gray scale if set to 1
- tft_max_rdclock current spi clock for reading from display RAM
- tft_width screen width (smaller dimension) in pixels
- tft_height screen height (larger dimension) in pixels
- tft_disp_type current display type (DISP_TYPE_ILI9488 or DISP_TYPE_ILI9341)

Full functions syntax and descriptions can be found in tft.h and tftspi.h files.

Full demo application, well documented, is included, please analyze it to learn how to use the library functions.

Connecting the display

ESP32 pin	Display module	Notes
Any output pin	MOSI	SPI input on Display module
Any pin	MISO	SPI output from Display module, optional
Any output pin	SCK	SPI clock input on Display module
Any output pin	CS	SPI CS input on Display module
Any output pin	DC	DC (data/command) input on Display module
Any output pin	TCS	Touch pannel CS input (if touch panel is used)
Any output pin	RST	optional, reset input of the display module, if not used pullup the reset input to Vcc
Any output pin	BL	optional, backlight input of the display module, if not used connect to +3.3V (or +5V)
GND	GND	Power supply ground
3.3V or +5V	Vcc	Power supply positive

Make sure the display module has 3.3V compatible interface, if not you must use level shifter!

To run the demo, attach ILI9341, ILI9488 or ST7735 based display module to ESP32. Default pins used are:

mosi: 23
miso: 19
sck: 18
CS: 5 (display CS)
DC: 26 (display DC)
TCS: 25 (touch screen CS)

Custom PINS can be defined in `idf.py menuconfig` in Components -> TFT Display menu

Display Kits

Predefined display configurations are available that will set pins, display size, and inversion properly for the specified kit.

Access these through the idf.py menuconfig in Components->TFT Display

Configurations are available for:

"ESP-WROVER-KIT v3 Display (ST7789V)"
"ESP-WROVER-KIT v4.1 Display (ILI9341)"
"Adafruit TFT Feather Display"
"M5Stack TFT Display"

Other config notes

Touch screen can be enabled in Components -> TFT Display as well.

Using idf.py menuconfig select tick rate 1000 ( → Component config → FreeRTOS → Tick rate (Hz) ) to get more accurate timings

Installing as Library

This repository is intended to be installable as a component library using the ESP-IDF 4.0 build system.

It is recommended though that you first follow the demo instructions below to build this repository as a standalone example to validate your hardware and have a basis to learn the library features.

When you are ready to incorporate it into your existing project, it is recommended to:

mkdir -p externals
git submodule add https://github.com/jeremyjh/ESP32_TFT_library.git externals/ESP32_TFT_library

In your project's root CMakeLists.txt add the components folder to EXTRA_COMPONENT_DIRS - make sure this is before the project() config e.g.

cmake_minimum_required(VERSION 3.5)

include($ENV{IDF_PATH}/tools/cmake/project.cmake)
    set(EXTRA_COMPONENT_DIRS
            externals/ESP32_TFT_library/components)

project(hello-world)

In your own components//CMakeLists.txt or main/CMakeLists.txt add tft and spiffs (if you are using spiffs) as REQUIRES e.g.

set(SOURCES tft_demo.c)
idf_component_register(
        SRCS ${SOURCES}
        INCLUDE_DIRS
          ${CMAKE_CURRENT_LIST_DIR}
          $ENV{IDF_PATH}/components
        REQUIRES
            tft
            spiffs
)

Building the Demo

Clone the repository to your esp folder (same level as esp-idf, as explained in instructions).

git clone https://github.com/jeremyjh/ESP32_TFT_library.git

Execute idf.py menuconfig and configure your Serial flash config and other settings. Included sdkconfig.defaults sets some defaults to be used.

Navigate to Components -> TFT Display and set display and pin options or select a pre-defined display configuration for a kit.

To enable Wifi in the demo (recommended - gets time from NTP), select TFT Display DEMO Configuration from the top-level menu and select those options.

Make and flash the example.

idf.py build && idf.py -p <PORT> flash monitor

Deploy the SPIFFS image as below to make the image and font examples work.

Prepare SPIFFS image

The demo uses some image and font files and it is necessary to flash the spiffs image.

To flash already prepared image to flash execute:

ESPPORT=<PORT> make copyfs

You can also prepare different SFPIFFS image and flash it to ESP32.

The example partition file reserves 1MB for SPIFFS. If you change the spiffs partition size, update the SPIFFS configuration as well.

idf.py menuconfig Navigate to Components -> TFT SPIFFS and set SPIFFS options.

Files to be included on spiffs are already in components/spiffs_image/image/ directory. You can add or remove the files you want to include.

Then execute:

make makefs

to create spiffs image in build directory without flashing to ESP32

Or execute:

ESPPORT=<PORT> make flashfs

to create spiffs image in build directory and flash it to ESP32

Example output:


I (0) cpu_start: App cpu up.
I (312) heap_init: Initializing. RAM available for dynamic allocation:
I (319) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM
I (325) heap_init: At 3FFBB0B8 len 00024F48 (147 KiB): DRAM
I (331) heap_init: At 3FFE0440 len 00003BC0 (14 KiB): D/IRAM
I (338) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM
I (344) heap_init: At 40091F94 len 0000E06C (56 KiB): IRAM
I (350) cpu_start: Pro cpu start user code
I (144) cpu_start: Starting scheduler on PRO CPU.
I (0) cpu_start: Starting scheduler on APP CPU.

==============================
TFT display DEMO, LoBo 09/2017
==============================

SPI: display device added to spi bus (2)
SPI: attached display device, speed=8000000
SPI: bus uses native pins: false
SPI: display init...
OK
SPI: Changed speed to 26666666

---------------------
Graphics demo started
---------------------
I (2815) [TFT Demo]: Time is not set yet. Connecting to WiFi and getting time over NTP.
I (2845) wifi: wifi firmware version: ee52423
I (2846) wifi: config NVS flash: enabled
I (2846) wifi: config nano formating: disabled
I (2846) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE
I (2856) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE
I (2890) wifi: Init dynamic tx buffer num: 32
I (2890) wifi: Init data frame dynamic rx buffer num: 32
I (2890) wifi: Init management frame dynamic rx buffer num: 32
I (2894) wifi: wifi driver task: 3ffc83d8, prio:23, stack:4096
I (2899) wifi: Init static rx buffer num: 10
I (2903) wifi: Init dynamic rx buffer num: 32
I (2907) wifi: Init rx ampdu len mblock:7
I (2911) wifi: Init lldesc rx ampdu entry mblock:4
I (2916) wifi: wifi power manager task: 0x3ffcd844 prio: 21 stack: 2560
I (2922) [TFT Demo]: Setting WiFi configuration SSID LoBoInternet...
I (2951) phy: phy_version: 359.0, e79c19d, Aug 31 2017, 17:06:07, 0, 0
I (2951) wifi: mode : sta (24:0a:c4:11:a4:0c)
I (3073) wifi: n:11 0, o:1 0, ap:255 255, sta:11 0, prof:1
I (3731) wifi: state: init -> auth (b0)
I (3734) wifi: state: auth -> assoc (0)
I (3738) wifi: state: assoc -> run (10)
I (3776) wifi: connected with LoBoInternet, channel 11
I (5827) event: ip: 192.168.0.21, mask: 255.255.255.0, gw: 192.168.0.1
I (5828) [TFT Demo]: Initializing SNTP
I (6331) [TFT Demo]: System time is set.
I (6331) wifi: state: run -> init (0)
I (6332) wifi: n:11 0, o:11 0, ap:255 255, sta:11 0, prof:1
I (6344) wifi: flush txq
I (6344) wifi: stop sw txq
I (6344) wifi: lmac stop hw txq
E (6344) wifi: esp_wifi_connect 836 wifi not start


I (8441) [SPIFFS]: Registering SPIFFS file system
I (8441) [SPIFFS]: Mounting SPIFFS files system
I (8441) [SPIFFS]: Start address: 0x280000; Size 1024 KB
I (8447) [SPIFFS]:   Work buffer: 2048 B
I (8451) [SPIFFS]:    FDS buffer: 384 B
I (8456) [SPIFFS]:    Cache size: 2048 B
I (8500) [SPIFFS]: Mounted

==========================================
Display: ILI9488: PORTRAIT 240,320 Color

     Clear screen time: 60 ms
Send color buffer time: 228 us (240 pixels)
       JPG Decode time: 287 ms
    BMP time, scale: 5: 422 ms
    BMP time, scale: 4: 431 ms
    BMP time, scale: 3: 430 ms
    BMP time, scale: 2: 434 ms
    BMP time, scale: 1: 442 ms
    BMP time, scale: 0: 335 ms

==========================================
Display: ILI9488: LANDSCAPE 320,240 Color

     Clear screen time: 57 ms
Send color buffer time: 301 us (320 pixels)
I (126333) event: station ip lost
       JPG Decode time: 286 ms
    BMP time, scale: 5: 422 ms
    BMP time, scale: 4: 431 ms
    BMP time, scale: 3: 433 ms
    BMP time, scale: 2: 435 ms
    BMP time, scale: 1: 444 ms
    BMP time, scale: 0: 260 ms

==========================================
Display: ILI9488: PORTRAIT FLIP 240,320 Color

     Clear screen time: 60 ms
Send color buffer time: 228 us (240 pixels)
       JPG Decode time: 287 ms
    BMP time, scale: 5: 420 ms
    BMP time, scale: 4: 430 ms
    BMP time, scale: 3: 429 ms
    BMP time, scale: 2: 436 ms
    BMP time, scale: 1: 446 ms
    BMP time, scale: 0: 338 ms

==========================================
Display: ILI9488: PORTRAIT FLIP 240,320 Color

     Clear screen time: 60 ms
Send color buffer time: 228 us (240 pixels)
       JPG Decode time: 287 ms
    BMP time, scale: 5: 420 ms
    BMP time, scale: 4: 430 ms
    BMP time, scale: 3: 429 ms
    BMP time, scale: 2: 436 ms
    BMP time, scale: 1: 446 ms
    BMP time, scale: 0: 338 ms