jflemer-ndp/libmpsse

Issues

• where is pylibmpsse ?

  #50 opened 10 years ago by GoogleCodeExporter
  1

• I2C eeprom python script available

  #51 opened 10 years ago by GoogleCodeExporter
  0

• Patch for /trunk/src/mpsse.c

  #52 opened 10 years ago by GoogleCodeExporter
  0

• How to address i2c slaves

  #46 opened 10 years ago by GoogleCodeExporter
  1

• I2C Read gives one bad bit, but only rarely

  #47 opened 10 years ago by GoogleCodeExporter
  0

• SetDirection in MPSSE mode

  #48 opened 10 years ago by GoogleCodeExporter
  0

• FIXED Apple OS X library compilation and installation with libftdi1 from MacPorts

  #49 opened 10 years ago by GoogleCodeExporter
  0

• Erronous start condition if using GPIO on low bits in i2c mode

  #42 opened 10 years ago by GoogleCodeExporter
  0

• pyswig versions of functions leaked into C library (libmpsse.a/.so)

  #43 opened 10 years ago by GoogleCodeExporter
  0

• FastTransfer always fails

  #44 opened 10 years ago by GoogleCodeExporter
  0

• Problems with the Setup

  #45 opened 10 years ago by GoogleCodeExporter
  0

• Patch for /trunk/src/mpsse.i

  #39 opened 10 years ago by GoogleCodeExporter
  1

• make install command does not work at MinGW

  #40 opened 10 years ago by GoogleCodeExporter
  0

• Failed to initialize MPSSE: device not found

  #41 opened 10 years ago by GoogleCodeExporter
  0

• WritePins always fails

  #38 opened 10 years ago by GoogleCodeExporter
  2

• Unable to build out-of-source

  #36 opened 10 years ago by GoogleCodeExporter
  4

• PATCH: multiple deive support

  #37 opened 10 years ago by GoogleCodeExporter
  0

• I2C Read is not working for me

  #35 opened 10 years ago by GoogleCodeExporter
  2

• SDA line held low even after a Stop issued.

  #34 opened 10 years ago by GoogleCodeExporter
  2

• configure isn't finding locally installed libftdi1

  #32 opened 10 years ago by GoogleCodeExporter
  2

• fast.o target is missing LIBFTDI1 define

  #33 opened 10 years ago by GoogleCodeExporter
  2

• Possible memory leak in Open method

  #31 opened 10 years ago by GoogleCodeExporter
  3

• FastTransfer doesn't work

  #30 opened 10 years ago by GoogleCodeExporter
  2

• fast.c fails to compile with libftdi1

  #28 opened 10 years ago by GoogleCodeExporter
  1

• Unable to make multiple simultaneous connections to separate interfaces

  #29 opened 10 years ago by GoogleCodeExporter
  3

• FT232H does not use open-drain outputs

  #27 opened 10 years ago by GoogleCodeExporter
  4

• SPI mode speedup by removing many memcopy

  #26 opened 10 years ago by GoogleCodeExporter
  4

• configure using "python --version" instead of "python -V" to find libraries

  #25 opened 10 years ago by GoogleCodeExporter
  1

• Failed to open MPSSE: device not found

  #24 opened 10 years ago by GoogleCodeExporter
  7

• Cannot send only 4 bits of data in SPI mode

  #23 opened 10 years ago by GoogleCodeExporter
  3

• SPI transfer with +1024 bytes size

  #22 opened 10 years ago by GoogleCodeExporter
  1

• unnecessary delay due to excessive buffer purging in raw_read

  #21 opened 10 years ago by GoogleCodeExporter
  2

• Feature request: Allow using adapter index to differentiate between multiple connected devices

  #19 opened 10 years ago by GoogleCodeExporter
  1

• libftdi/ftdi.h

  #20 opened 10 years ago by GoogleCodeExporter
  1

• SetMode sets all high byte pins to output

  #18 opened 10 years ago by GoogleCodeExporter
  1

• No ability to bulk set pins, or set pin direction.

  #17 opened 10 years ago by GoogleCodeExporter
  3

• missing standard functions

  #16 opened 10 years ago by GoogleCodeExporter
  11

• One too many clock edges are output whe using SPI modes 1 and 3

  #15 opened 10 years ago by GoogleCodeExporter
  5

• I2C start condition have a bug

  #13 opened 10 years ago by GoogleCodeExporter
  5

• gpio example segfaults

  #14 opened 10 years ago by GoogleCodeExporter
  2

• Fix makefile to make libmpsse easier to package

  #12 opened 10 years ago by GoogleCodeExporter
  1

• Write before read & transfer required, Transfer broken with FT232H

  #10 opened 10 years ago by GoogleCodeExporter
  5

• clock rates > 15MHz cause a hardware baudrate of 30MHz

  #11 opened 10 years ago by GoogleCodeExporter
  1

• PinHigh/PinLow do not seem to function as would be expected.

  #9 opened 10 years ago by GoogleCodeExporter
  17

• Can't read bytes sent during write cycle

  #8 opened 10 years ago by GoogleCodeExporter
  11

• Added selection on basis of product description (iProduct)

  #7 opened 10 years ago by GoogleCodeExporter
  1

• build_block_buffer() does not end I2C read sequence with NACK

  #6 opened 10 years ago by GoogleCodeExporter
  5

• Open() opens wrong interface

  #5 opened 10 years ago by GoogleCodeExporter
  3

• fix typos

  #4 opened 10 years ago by GoogleCodeExporter
  2

• Vid and Pid are not set

  #3 opened 10 years ago by GoogleCodeExporter
  1