Mopeka 3 tank config, 3rd tank not working after upgrade

[msteil4vse]

Steps to Reproduce

Hello,

Upgraded chrome on Pi, and most current version of Genmon this AM, post upgrade Pi reports 3rd tank "No Sensor Comms" I can see signals (all 3 tanks) are present at location of Pi installation, and it works correctly pre-upgrade. see log below, and please advise what further information is needed to troubleshoot.

Also do not know what "Unsupported GAP report type 0x2 on sensor" is about or if needs attention.

2024-03-19 07:35:06,243 : starting scan
2024-03-19 07:35:06,244 : Start Scan Filtered
2024-03-19 07:35:09,401 : Unsupported GAP report type 0x2 on sensor BDAddress('F2:34:95:E4:B7:95')
2024-03-19 07:35:09,402 : data: ['0x1', '0x0', '0x1', '0x95', '0xb7', '0xe4', '0x95', '0x34', '0xf2', '0x12', '0xd', '0xff', '0x59', '0x0', '0x8', '0x6c', '0x2a', '0xf9', '0x40', '0xe4', '0xb7', '0x95', '0xfd', '0xd5', '0x3', '0x2', '0xe5', '0xfe', '0xbc']
2024-03-19 07:35:09,403 : Sensor Type: PRO+ Bottom-up Boosted BLE sensor, all commodities
2024-03-19 07:35:09,404 : Battery Volts: 3.375 V
2024-03-19 07:35:09,405 : Battery Percent: 100.0%
2024-03-19 07:35:09,405 : Temp: 35.6 F
2024-03-19 07:35:09,406 : Reading MM: 110 mm
2024-03-19 07:35:09,406 : Reading inches: 4.33 inches
2024-03-19 07:35:09,406 : Reading Quality: 1
2024-03-19 07:35:21,245 : Stop Scan Filtered
2024-03-19 07:35:21,245 : stopped scan
2024-03-19 07:35:21,246 : Processed Ads:90
2024-03-19 07:35:21,246 : Rejected Ads:0
2024-03-19 07:35:21,247 : Skipped Ads:0
2024-03-19 07:35:21,248 : Zero Length Ads:46
2024-03-19 07:35:21,248 : Ignored Ads:910
2024-03-19 07:35:21,248 : Tank Level in mm: 110
2024-03-19 07:35:21,249 : Tank Level in inches: 4.33
2024-03-19 07:35:21,249 : Gallons Left: 52.87
2024-03-19 07:35:21,250 : Tank Percentage: 5.25
2024-03-19 07:35:21,250 : Tank1 = 5.25
2024-03-19 07:35:21,250 : Tank Level in mm: 120
2024-03-19 07:35:21,251 : Tank Level in inches: 4.72
2024-03-19 07:35:21,251 : Gallons Left: 60.21
2024-03-19 07:35:21,251 : Tank Percentage: 5.97
2024-03-19 07:35:21,252 : Tank2 = 5.97
2024-03-19 07:35:21,253 : No sensor comms detected for BDAddress('F5:49:AD:48:6D:6D')
2024-03-19 07:35:21,254 : Tank Data = {"Percentage": 5.25, "Percentage2": 5.97, "Percentage3": 0, "Tank Name": "Mopeka Sensor Tank"}
2024-03-19 07:35:21,256 : SendCommand Result: OK

Expected Result

see above

Actual Result

see above

Version Info

see above

Logs

genmon_logs.tar.gz

[msteil4vse]

Disregard, tank/sensor data magically started working after Pi was online for about an hour.