Summary

This is the PIC18F25K50 firmware for Prog, a programmer for selected Microchip PIC16F, PIC18F and PIC32F microcomputers. The programmer is a PIC18F25K50 with associated circuitry that connects to a PC over USB and to the PIC to be programmed. It is controlled from the PC using the Prog-Win command line utility, which reads HEX files. Typically the HEX file would have been generated by one of the (free) Microchip compilers.

+----------------+       +-------------+        +------------------------------+
| Windows PC     |       | Programmer  |--Vdd-->| PIC16/18/32 to be programmed |
|                |       |             |--Gnd-->|                              |
|  prog-win.exe <---USB->| PIC25K50    |<-PGD-->|                              |
|                |       | MAX680      |--PGC-->|                              |
+----------------+       +-------------+  etc.. +------------------------------+

Note that the picture above illustrates the Prog chicken-and-egg problem; without access to a preprogrammed PIC18F25K50 you need the programmer to program the programmer PIC.

Supported PICs

The following PICs have been tested:

PIC16F:
- PIC16F628A
- PIC16F648A
PIC18F:
- PIC18F2450
- PIC18F2550
- PIC18F4550
- PIC18F25K50
- PIC18F1330
PIC32MX
- PIC32MX150F128
- PIC32MX220F032
- PIC32MX250F128

...but any device using any of the five programming specifications should work. The specifications are Microchip documents:

PIC16: DS41196E "PIC16F6xx/A EEPROM Programming Specification". This firmware implements the high-voltage In-Circuit Serial Programming (ICSP) specification.
PIC18: DS39622F "Flash Microcontroller Programming Specification", DS41630B (with the same title) and DS39752B (with the same title). This firmware implements the high-voltage In-Circuit Serial Programming (ICSP) specification.
PIC32: DS66145J "PIC32MX Flash Programming Specification". This firmware implements the 4-wire JTAG interface (not the 2-wire In-Circuit Serial Programming (ICSP) specification).

The following devices are covered by the specs:

PIC16F627A
PIC16LF627A
PIC16F628A
PIC16LF628A
PIC16F648A
PIC16LF648A
PIC18F1230
PIC18F1330
PIC18F2221
PIC18F2321
PIC18F2410
PIC18F2420
PIC18F2450
PIC18F24K50
PIC18LF24K50
PIC18F2455
PIC18F2480
PIC18F2510
PIC18F2515
PIC18F2520
PIC18F2525
PIC18F2550
PIC18F25K50
PIC18LF25K50
PIC18F2580
PIC18F2585
PIC18F2610
PIC18F2620
PIC18F26K50
PIC18LF26K50
PIC18F2680
PIC18F4221
PIC18F4321
PIC18F4410
PIC18F4420
PIC18F4450
PIC18F45K50
PIC18F4455
PIC18F4480
PIC18F4510
PIC18F4515
PIC18F4520
PIC18F4525
PIC18F4550
PIC18LF45K50
PIC18F4580
PIC18F4585
PIC18F4610
PIC18F4620
PIC18F46K50
PIC18LF46K50
PIC18F4680
All PIC32MX devices

Build

This repo is configured for MPLAB-X v3.55 (the free IDE from Microchip) and XC v1.41 (a C compiler with a free option). It uses the Microchip MCC v1.35.

Pins

The pins to connect to the device to be programmed are (in addition to GND):

Pin	PIC16 and PIC18	PIC32
RB5		MCLR
RB4		TMS
RB3	Vpp
RB2	Vdd	TDO
RB1	PDG	TCK
RB0	PGC	TDI

Circuit

The PIC18F25K50 connects to the PC over a USB cable. A MAX680 is used to pump a 5V supply to the required Vpp 10V for PIC16 and PIC18. Only half of the MAX680 is used; there's no need for a -10V.

For pure PIC32 programming the MAX680 and associated circuitry can be omitted.

Various bypass caps are not shown below; see the PIC18F25K50 documentation.

Driver

Windows 7 and up contain a generic USB driver sufficient for Prog. When the programmer is connected to the Windows PC and a driver is asked for, nominate the "windows driver" directory in this repo. This will trigger Windows to read the prog.inf file and using the information within configure the Prog hardware as a generic USB device. Once successful, the Prog-Win command line utility is used to work with the programmer.

Limitations

There is currently no support for programming data EEPROM (read: semi-static RAM). There's no technical reason for why it could not be added, I just never needed it.

Known Issues

Sometimes, and in particular with long (>100mm) leads between the programmer and the chip to be programmed, the verification step may fail. Another try often helps. Shorter leads does too.

TODO

Support for data EEPROM.

jhbe/prog-25k50