screenshot-actions

Dunst actions for screenshots. Current actions include:

clipboard mode: works with screenshots that were saved to the clipboard
- Extract text from screenshot using ocr
- Save screenshot stored in clipboard to an image file
- Upload screenshot to 0x0.st
file mode: works with screenshots that were saved to a file
- Delete screenshot
- Rename screenshot
- Copy screenshot to clipboard
- Move screenshot to clipboard (deletes file)
- Upload screenshot to 0x0.st

Currently supports scrot, maim, and flameshot. New screenshot tools can be added easily (see screenshot.sh configuration section).

The tool is simple to install, configure, and use. See the instructions below. Examples are also at the bottom of this document.

Requirements

dunst (notification daemon)
dmenu (for selecting dunst actions)
xclip (for managing clipboard)
zenity (for saving/renaming files)
tesseract (for OCR)
tesseract-data-* (for OCR)
scrot, maim, or flameshot. Submit an issue request for support for other screenshot tools

Installation/Setup instructions

Installation instructions for an arch based distribution are provided under the assumption that most people using dunst are using an arch based distribution. Installation instructions should be similar for other distributions as well.

Install required packages

sudo pacman -Syu dunst dmenu zenity xclip tesseract tesseract-data-eng

The above command assumes you which to use english OCR data. If you wish to have a different language, please refer to the aur page for tesseract.

Install screenshot-actions

Clone the repository and run ./install.sh.

Run ./install.sh anytime you modify any of the files!

git clone https://github.com/jrodal98/screenshot-actions.git
cd screenshot-actions
./install.sh

If you get a "Permission denied" error, try running "chmod +x install.sh" and then run ./install.sh again.

NOTE: Icons and Flameshot aren't supported without configuration. Fear not, configuring the script is very simple.

Make sure you set SCREENSHOT_DIR at the top of the variables.sh file or else your files won't end up where you want them!

Configuring screenshot-actions

There are two files that the average user should be aware of: variables.sh and screenshot.sh. variables.sh contains some variables that the other scripts need to be aware of, such as the path to the directory you wish to save screenshots in. screenshot.sh is an optional controller that takes screenshots and then calls the screenshot_actions.sh script, which sends the dunst notifications and does different actions. If you wish to change the screenshot options that scrot, maim, or flameshot do, or if you wish to add another screenshot tool, it should be added to screenshot.sh.

Flameshot requires a bit of additional configuration, which I will describe below.

`variables.sh`

The icons and camera shutter variables are optional

# required
SCREENSHOT_DIR="path to screenshot directory"
ACTIONS_PATH="path to the screenshot_actions.sh file (this variable shouldn't have to be changed)"
OCR_LANG="OCR language code (eng for english)"

# Optional

ERROR_ICON="Path to icon displayed when an error occurs"
CAMERA_ICON="Path to icon displayed when a normal operation occurs"
OCR_ICON="Path to icon displayed when OCR is invoked"
CAMERA_SHUTTER="Path to sound file played when a screenshot is taken"

`screenshot.sh`

When adding your own screenshot methods, you should do the following:

put the name of the tool in the outermost case statement
put your desired alias for your screenshot method in an inner case statement
call $ACTIONS_PATH PATH_TO_FILE or $ACTIONS_PATH CLIPBOARD, depending on whether the screenshot was saved to a file or to the clipboard.

I posted the default configuration for maim, as it showcases this philosophy the best. scrot allows you to execute a script after taking a screenshot, so I used that instead of following the algorithm above. Flameshot isn't very unix like and thus the solution is hacky and doesn't follow the algorithm above either.

"maim")
    case "$2" in
        fullToFile )
            FILENAME=$SCREENSHOT_DIR/$(date +%s).png
            maim $FILENAME
            $ACTIONS_PATH $FILENAME
            ;;
        fullToClip )
            maim | xclip -selection clipboard -t image/png
            $ACTIONS_PATH clipboard
            ;;
        selectToFile )
            FILENAME=$SCREENSHOT_DIR/$(date +%s).png
            maim -s $FILENAME
            $ACTIONS_PATH $FILENAME
            ;;
        selectToClip )
            maim -s | xclip -selection clipboard -t image/png
            $ACTIONS_PATH clipboard
            ;;
        windowToFile )
            FILENAME=$SCREENSHOT_DIR/$(date +%s).png
            maim -i $(xdotool getactivewindow) $FILENAME
            $ACTIONS_PATH $FILENAME
            ;;
        windowToClip )
            maim -i $(xdotool getactivewindow) | xclip -selection clipboard -t image/png
            $ACTIONS_PATH clipboard
            ;;
        *)
            send_error "$2 is not a supported action for $1"
            ;;
    esac
    ;;

A note on Flameshot

Flameshot is a bit trickier to use than scrot or maim. To use flameshot, make sure that flameshot notifications are turned on. You can modify this using flameshot config in your terminal and making sure "show desktop notifications" is selected. Then, add the following code to the bottom of your dunstrc file:

[change_flameshot]
    appname = flameshot
    format = ""
    script = ~/.config/dunst/screenshot.sh

Examples

General usage: ./screenshot.sh SCREENSHOT_PROGRAM SCREENSHOT_TYPE

Once your dunst notification appears, trigger the dunst context menu to access the actions provided by my program. Navigate the actions using dmenu. If you are unfamiliar with either of these concepts, please refer to their documentation.

You can see what keybinding triggers your context menu by looking at context variable in the shortcuts section of your dunstrc configuration.

Scrot

Take a screenshot of the full display and save it to a file: ./screenshot.sh scrot fullToFile
Take a screenshot of the full display and copy it to the clipboard: ./screenshot.sh scrot fullToClip
Take a screenshot using selection tool and save it to a file: ./screenshot.sh scrot selectToFile
Take a screenshot using selection tool and copy it to the clipboard: ./screenshot.sh scrot selectToClip
Take a screenshot of active window and save it to a file: ./screenshot.sh scrot windowToFile
Take a screenshot of active window and copy it to the clipboard: ./screenshot.sh scrot windowToClip

Maim

Take a screenshot of the full display and save it to a file: ./screenshot.sh maim fullToFile
Take a screenshot of the full display and copy it to the clipboard: ./screenshot.sh maim fullToClip
Take a screenshot using selection tool and save it to a file: ./screenshot.sh maim selectToFile
Take a screenshot using selection tool and copy it to the clipboard: ./screenshot.sh maim selectToClip
Take a screenshot of active window and save it to a file: ./screenshot.sh maim windowToFile
Take a screenshot of active window and copy it to the clipboard: ./screenshot.sh maim windowToClip

Flameshot

Take a screenshot of the full display and save it to a file: ./screenshot.sh flameshot full
Open the flameshot gui tool: ./screenshot.sh flameshot select

Contributing

I will accept pull requests on this repository for adding different screenshot tools to screenshot.sh, adding new actions to screenshot_actions.sh, reasonable refactoring of preexisting code, etc. Feel free to submit an issue request if there's a specific action you'd like to see. No guarantees, but if it sounds cool and sounds like something I'm capable of implementing, I might implement it.