🌟LilyGo LoRa Series🌟

English | 中文

USE Arduino IDE

Install the current upstream Arduino IDE at the 1.8 level or later. The current version is at the Arduino website. (NOTE: MacOS may require that you install separate drivers to interact with your board. You will get error messages that occur when the IDE attempts to upload code. You should consider running the Arduino IDE in a Virtual Machine on Linux. Installing other drivers on your Mac is out of scope for this document.)
Start Arduino and open Preferences window. In additional board manager add url: https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_index.json If you have multiple URLs (e.g., for other boards), just add previously mentioned URL, separated by a comma.
Copy all folders in the lib directory to your Arduino Libraries Directory,

in MacOS, it is ~/Documents/Arduino/libraries
in Linux, it is ~/Arduino/libraries
in Windows, it is Documents/Arduino/libraries

Open the corresponding example
In the Arduino Application, navigate to the Board Manager menu ("Tools => Board => Board Manager"), search for esp32, and make sure that you install the latest version. After you do this, you can select the board you have from the list of boards in the "ESP32 Arduino" menu ("Tools=> Board => ESP32 Arduino"). It's very important to note that the list of boards is NOT in alphabetical order. Look for the board you are working with carefully in the list.
T-Beam users can choose TTGO T-Beam, lora32(T3) users can choose ESP32 Dev Module , T-Motion users choose Nucleo_l073RZ,T3-S3-V1.0and T-BeamS3 Supreme users can selected ESP32S3 Dev Module
Select the port of the board in the port
Please uncomment the utility.h file above each sketch based on your board model, otherwise compilation will report an error
Upload

⚠ Cautions ⚠

When using the SX1280 PA T3S3 V1.1 (V1.2 does not have this issue), it is recommended that the software control 1280 chip output 2 to 5 dbm, so that the entire module will output 20 dbm of power; When the output of 1280 chip is higher than 2 dbm, the output power of the entire module is only 20 dbm; When the output of 1280 chip is higher than 5 dbm, the output power of the entire module is only 20 dbm, but if 5 dbm is given to the FEM, it will damage the FEM chip (the maximum allowable input for the FEM is 5 dbm) If the output of the 1280 chip is lower than 2 dbm, the output power of the entire module is within 20 dbm. The output power setting of the SX1280 cannot be greater than 2-5dbm, otherwise damage to the FEM chip may occur. Set 3dBM to have an output power of 20dmb

Product 📷

Product	Product Link	Schematic	Corresponding example macro definition
T-Beam SX1278/76	AliExpress	TBeamV0.7 / TBeamV1.0 / TBeamV1.1	LILYGO_TBeam_V0_7 / LILYGO_TBeam_V1_X
T-Beam SX1262	AliExpress	TBeamV0.7 / TBeamV1.0 / TBeamV1.1	LILYGO_TBeam_V0_7 / LILYGO_TBeam_V1_X
LoRa32 V1.0 SX1276	AliExpress	❌	LILYGO_T3_V1_0
LoRa32 V1.0 SX1278	AliExpress	❌	LILYGO_T3_V1_0
LoRa32 V1.3 SX1276	AliExpress	LoRa32 V1.3	LILYGO_T3_V1_3
LoRa32 V2.0	AliExpress	LoRa32 V2.0	LILYGO_T3_V2_0
LoRa32 V2.1 & 1.6	AliExpress/Amazon	LoRa32 V2.1_1.6	LILYGO_T3_V1_6
T-Motion S76G	AliExpress	T-Motion	LILYGO_T_MOTION_S76G
LoRa32 V1.8 2.4G	lilygo.cc	LoRa32 V1.8 2.4G	LILYGO_T3_V1_8
LoRa T3 S3 V1.0	lilygo.cc	LoRa T3 S3 V1.0	LILYGO_T3_S3_V1_0
LoRa T3 S3 V1.1	lilygo.cc	LoRa T3 S3 V1.1	LILYGO_T3_S3_V1_0 (Same as 1.0)
T-Beam S3 Supreme/T-BeamS3 Core	lilygo.cc	T-Beam S3 Supreme & T-Beam S3 Core	LILYGO_TBeamS3_SUPREME_V3_0

Example description

├─ArduinoLoRa       # Only support SX1276/SX1278 radio module
│  ├─LoRaReceiver
│  └─LoRaSender
├── Display         # Only supports TBeam TFT Shield
│   ├── Free_Font_Demo
│   ├── TBeam_TFT_Shield
│   ├── TFT_Char_times
│   └── UTFT_demo
├─GPS                           # T-Beam GPS demo examples
│  ├─TinyGPS_Example
│  ├─TinyGPS_FullExample
│  ├─TinyGPS_KitchenSink
│  ├─UBlox_BasicNMEARead        # Only support Ublox GNSS Module 
│  ├─UBlox_Recovery             # Only support Ublox GNSS Module 
│  ├─UBlox_OutputRate           # Only support Ublox GNSS Module 
│  └─UBlox_NMEAParsing          # Only support Ublox GNSS Module 
├─OLED                          # OLED demo examples
│  ├─SH1106FontUsage
│  ├─SH1106GraphicsTest
│  ├─SH1106IconMenu
│  ├─SH1106PrintUTF8
│  ├─SSD1306SimpleDemo
│  └─SSD1306UiDemo
├─RadioLibExamples              # RadioLib examples,Support SX1276/78/62/80
│  ├─SX1262
│  │  ├─SX1262_Receive_Interrupt
│  │  └─SX1262_Transmit_Interrupt
│  ├─SX1268
│  │  ├─SX1268_Receive_Interrupt
│  │  └─SX1268_Transmit_Interrupt
│  ├─SX1276
│  │  ├─SX1276_Receive_Interrupt
│  │  └─SX1276_Transmit_Interrupt
│  ├─SX1278
│  │  ├─SX1278_Receive
│  │  ├─SX1278_Receive_Interrupt
│  │  ├─SX1278_Transmit
│  │  └─SX1278_Transmit_Interrupt
│  ├─SX1280
│  │  ├─Ranging
│  │  │  ├─Ranging_Master
│  │  │  └─Ranging_Slave
│  │  ├─SX128x_Receive_Interrupt
│  │  └─SX128x_Transmit_Interrupt
│  └─TBeamAllFunction   # T-Beam all function example,Only tbeamv1.x is supported temporarily
├── Sensor            # Sensor examples , just support t-beams3-supreme
│   ├── BME280_AdvancedsettingsExample
│   ├── BME280_TestExample
│   ├── BME280_UnifiedExample
│   ├── PCF8563_AlarmByUnits
│   ├── PCF8563_SimpleTime
│   ├── PCF8563_TimeLib
│   ├── PCF8563_TimeSynchronization
│   ├── QMC6310_CalibrateExample
│   ├── QMC6310_CompassExample
│   ├── QMC6310_GetDataExample
│   ├── QMC6310_GetPolarExample
│   ├── QMI8658_BlockExample
│   ├── QMI8658_GetDataExample
│   ├── QMI8658_InterruptBlockExample
│   ├── QMI8658_InterruptExample
│   ├── QMI8658_LockingMechanismExample
│   ├── QMI8658_MadgwickAHRS
│   ├── QMI8658_PedometerExample
│   ├── QMI8658_ReadFromFifoExample
│   └── QMI8658_WakeOnMotion
├─SleepTest
└─LoRaWAN                           # OTAA method Join TTN example
    └─OTTA

Radio resolution

How to distinguish the model of Radio just need to look at the sticker on the board, 433MHz is SX1278, 868MHz is SX1276, If the label says SX1262 then it is SX1262

Precautions

If there is no data output from GPS, see Restoring factory defaults
GNSS troubleshooting from SoftRF

PinOut

See utilities.h

Application

TTN

To quickly start using TTN (The Things Network), please refer to LilyGo_LoRa_Series_Quick_Start

Datasheet :

Announcements

After setting the LoRa output power, set the lowest current. Set sx1262 as follows :

    // digitalWrite(LoRa_Busy, LOW);
    // set output power to 10 dBm (accepted range is -17 - 22 dBm)
    if (radio.setOutputPower(22) == RADIOLIB_ERR_INVALID_OUTPUT_POWER) {
        Serial.println(F("Selected output power is invalid for this module!"));
        while (true);
    }


    // set over current protection limit to 80 mA (accepted range is 45 - 240 mA)
    // NOTE: set value to 0 to disable overcurrent protection
    if (radio.setCurrentLimit(80) == RADIOLIB_ERR_INVALID_CURRENT_LIMIT) {
        Serial.println(F("Selected current limit is invalid for this module!"));
        while (true);
    }

FAQ

LILYGO_TBeamS3_SUPREME_V3_0 The GPS backup power comes from the 18650 battery. If you remove the 18650 battery, you will not be able to get the GPS hot start. If you need to use the GPS hot start, please connect the 18650 battery

jry485/LilyGo-LoRa-Series