jschuh/klipper-macros

Issues

• [BUG] Unable to delay extruder final temperature (no bed leveling or probing)

  #269 opened 16 days ago by wespiard
  0

• Add UNLOAD_FILAMENT_AFTER_PRINT macro

  #261 opened 3 months ago by HitLuca
  1

• Feature: set temperature while meshing

  #254 opened 5 months ago by pheidrias
  3

• [BUG] Bed names can't be larger than 10 characters.

  #265 opened 2 months ago by stonemandave
  0

• Error evaluating 'gcode_macro bed_mesh_check:gcode': gcode.CommandError: Warning: The following issue(s) were detected in your [bed_mesh] config:

  #264 opened 2 months ago by neokamen
  0

• Error evaluating 'gcode_macro Z_TILT_ADJUST:gcode': jinja2.exceptions.UndefinedError: 'extras.gcode_macro.GetStatusWrapper object' has no attribute 'gcode_macro _User_Variables'

  #262 opened 3 months ago by bgobiel
  0

• [BUG] Homing bypassing [Probe] Activate Gcode

  #259 opened 4 months ago by Firas95k
  1

• [BUG] sensorless homing - Macro G28 called recursively

  #257 opened 4 months ago by sredoje1973
  0

• [BUG] MAKE_SURFACE_MESH fails with "Move out of range"

  #255 opened 4 months ago by stablestud
  1

• When using bed_mesh.cfg in optional folder, 1st layer is messed up.

  #252 opened 5 months ago by T9Air
  1

• [BUG] PARK macro from a home state slows the feedrate to about 1mm/S

  #250 opened 5 months ago by suprchunk
  0

• I get an error Existing command 'SET_PRINT_STATS_INFO' not found in gcode_macro rename

  #247 opened 6 months ago by SplinMS
  1

• bed is crashing into Y max position

  #140 opened a year ago by Trei-D
  2

• [BUG] _km_check_and_set_print_bounds macro fails if `MESH_MIN` or `MESH_MAX` have negative values

  #242 opened 8 months ago by HitLuca
  2

• Klipper update breaks beeper

  #235 opened 8 months ago by HitLuca
  2

• Adaptive bed meshing integrated into mainline klipper

  #239 opened 8 months ago by HitLuca
  1

• [Freature Request] Make Beeps optional

  #226 opened 8 months ago by j16sdiz
  0

• [Freature Request] Event for idling (_km_idle_timeout)

  #227 opened 8 months ago by j16sdiz
  2

• [BUG] Option 'relative_reference_index' is not valid in section 'bed_mesh'

  #231 opened 8 months ago by M3HNGRY
  4

• BigTreeTech - Pi v1.2 Macros [BUG]

  #232 opened 8 months ago by Skybound420
  1

• [BUG] Too Much Retract on PRINT_END for Microswiss Hotends

  #229 opened 8 months ago by SSPW
  3

• [BUG] variable_load_speed in printer.cfg is not working

  #217 opened a year ago by wesblake
  1

• [FEATURE] Add temperature scaling to Bed Surfaces

  #221 opened a year ago by lettore
  0

• [BUG] - v0.8.8 issue with purge line not working anymore

  #220 opened a year ago by KaratsuFr
  1

• Multiples printer

  #213 opened a year ago by bluemorphe
  1

• Checking for extruder instead of heater in temperature menus

  #199 opened a year ago by KRTac
  3

• Non Blocking Heating Up

  #204 opened a year ago by jzhvymetal
  0

• [BUG] Tempurature on heated bed not being retained for print

  #205 opened a year ago by ultimatehecker
  0

• Z-offset not resetting to 0 after SAVE_CONFIG

  #190 opened a year ago by HitLuca
  5

• [BUG] Error evaluating 'gcode_macro _print_end_inner:gcode': jinja2.exceptions.UndefinedError: tuple object has no element 0

  #198 opened a year ago by mochoandre
  0

• Make the nozzle not end the purge line when over the initial purged blob

  #183 opened a year ago by HitLuca
  0

• [BUG] Errors in console from default macros

  #185 opened a year ago by josurr
  3

• [Enhancement] Heating the hotend after or while finishing the adaptive mesh

  #187 opened a year ago by kilinccagatay
  1

• Help: M600 Filament change, pooping in the middle of print after filament change and clicking resume.

  #182 opened a year ago by anuragdeshpande
  4

• Change m141

  #194 opened a year ago by bluemorphe
  0

• [BUG] Resume macro

  #193 opened a year ago by appleimperio
  1

• [Enhancement] Support multi-level print_end

  #180 opened a year ago by dpeart
  2

• [BUG] - Pause at layer pauses before and after the layer?

  #178 opened a year ago by AndyHazz
  0

• Documentation for OrcaSlicer

  #162 opened a year ago by buker
  1

• Stepper_x has no attribute

  #173 opened a year ago by platini76
  0

• [REQUEST] Support for dockable probe

  #164 opened a year ago by CarnageMarkus
  0

• [BUG] All surface offsets are changed after PROBE_CALIBRATE

  #158 opened a year ago by lettore
  4

• [BUG]variable_start_end_park_x missing

  #161 opened a year ago by SarcasmRules
  1

• getting a error message

  #157 opened a year ago by Senthiele
  1

• [BUG] - Manual QGL doesn't fire events

  #153 opened a year ago by agreen
  0

• Im using a dock able probe, cant get it to work with that config

  #150 opened a year ago by SvenixS
  0

• [BUG]Error evaluating 'gcode_macro BED_MESH_CALIBRATE:gcode': UndefinedError: 'dict object' has no attribute 'polygon'

  #148 opened a year ago by Johnn201
  3

• installing on multiple klipper instances

  #147 opened a year ago by drumstick77
  1

• How to make the bed move forward after printing, and not backward?

  #135 opened a year ago by Serj121
  1

• [Enhancment/Feature Request] Introduce Z Fade height

  #130 opened a year ago by thisisnotfez
  0