/modwifi

Primary LanguageShell

Advanced Wi-Fi Attacks Using Commodity Hardware

We provide tools to perform low-layer attacks such as reactive and constant jamming using commodity devices. Reactive jamming allows you to block specific Wi-Fi packets. For example, all beacons and probe responses of a specific Access Point (AP) can be jammed. It has been tested with the following devices:

This work was the result of the paper Advanced Wi-Fi Attacks Using Commodity Hardware presented at ACSAC 2014. If you use these tools in your research, please reference this paper. Most code is open source, and contributions are welcome. The code of the constant jammer can be requested but is not available publicly. Don't worry, we won't bite.

  • April 2016: we now support Linux kernels 3.0 up to and including 4.4! See the modwifi-4.4-1.tar.gz release! This has been tested on Arch Linux and Ubuntu 15.10.
  • September 2019: we have a release that supports kernels 5.3 and below. See the modwifi-5.3-rc4-1.tar.gz release. This was tested on kernel 4.9.0-9 and 5.2.9.

Table of Contents

Quick Start

You can download a VMWare image that has the drivers, firmware, and user-land tools preinstalled. Just boot it, plug-in the USB dongle, and start experimenting! The password of the account modwifi is modwifi. Once booted, you can execute (the public) attacks below.

Basic Usage

This section describes the attacks that can be executed. We assumed you already downloaded the VMWare image or manually installed the drivers and firmware (see the section "Installation" to install drivers on your existing machine).

Before doing any attacks it is recommended to disable WiFi. In particular I mean disabling WiFi in your network manager. Most graphical network managers have an option somewhere named "Enable Wi-Fi". Make sure it's not selected. If you can't find it, perhaps you can disable in the terminal with sudo nmcli nm wifi off. Once you have disabled WiFi your OS won't interfere with our attacks.

If RF-kill is enabled we'll have to turn it off. Some distributions set RF-kill on after disabling WiFi. But we still want to actually use our WiFi devices. So execute:

sudo apt-get install rfkill
sudo rfkill unblock wifi

Reactive Jamming

Our current implementation of our reactive jammer allows you to block an Access Point. More precisely, all beacons and probe responses will be jammed. Execute it using:

modwifi@ubuntu:~/modwifi/tools$ sudo rfkill unblock wifi
modwifi@ubuntu:~/modwifi/tools$ sudo iw wlan0 set type monitor
modwifi@ubuntu:~/modwifi/tools$ sudo ifconfig wlan0 up
modwifi@ubuntu:~/modwifi/tools$ sudo iw wlan0 set channel 11
modwifi@ubuntu:~/modwifi/tools$ sudo ./reactivejam -i wlan0 -s "Home Network"

The first three commands need to be executed only once after plugging in your dongle. To get the interface name of the wireless card you can execute iwconfig. In this case our targeted AP was on channel 11, but remember that your targeted AP may be on a different channel.

You can stop the reactive jammer using CTRL+C. It may take a few seconds before it actually stops. By modifying the firmware you can reactive jam any kind of packets you like. For example, you could jam all packets of a specific client. Note that only medium to large packets can be reliably jammed (see our paper).

You can verify that this works by monitoring the channel with a second device. Make sure that this device also reports corrupted frames using:

sudo iw wlan1 set monitor fcsfail

This will instruct the driver to also pass corrupted frames to the userland (when in monitor mode). Be warned though, not all drivers properly support this flag. Some will always show corrupted frames. Others will never show corrupted frames. Our drivers and firmware handle this flag correctly!

Disabling Carrier Sense

Want to disable carrier sense in order to perform an experiment? Then execute this:

modwifi@ubuntu:~$ sudo su
root@ubuntu:~$ mount -t debugfs none /sys/kernel/debug
root@ubuntu:~$ cd /sys/kernel/debug/ieee80211/phy*/ath9k_htc/registers/
root@ubuntu:~$ echo 1 > force_channel_idle
root@ubuntu:~$ echo 1 > ignore_virt_cs

Writing 1 to force_channel_idle disables physical carrier sense (channel is busy). Writing 1 to ignore_virt_cs disables virtual carrier sense (RTS/CTS). Random backoff parameters can also be changed.

Constant Jamming

If you have the firmware capable of doing constant jamming, you can execute:

modwifi@ubuntu:~/modwifi/tools$ sudo iw wlan0 set type monitor
modwifi@ubuntu:~/modwifi/tools$ sudo ifconfig wlan0 up
modwifi@ubuntu:~/modwifi/tools$ sudo ./constantjam wlan0 6

This performs constant jamming on channel 6. Because channels overlap, nearby channels will also be jammed. Remember that the constant jamming implementation is not public, but can be requested privately.

Unfair Channel Usage

The specific scripts we used to easily configure a device to act unfairly are not public. The reason behind this is that it's hard to defend against these kind of attacks. However, some parameters can still be accessed as debugfs entries in /sys/kernel/debug/ieee80211/phy*/ath9k_htc/registers/.

Forcing Corrupt Packets

You can force the wireless chip to calculate a wrong CRC (FCS) using:

modwifi@ubuntu:~$ sudo su
root@ubuntu:~$ mount -t debugfs none /sys/kernel/debug
root@ubuntu:~$ cd /sys/kernel/debug/ieee80211/phy*/ath9k_htc/registers/
root@ubuntu:~$ echo 1 > diag_corrupt_fcs

Channel MitM and TKIP Broadcast Attack

This is an advanced attack and not for the fainthearted. It clones an existing Access Point on a different channel. This allows us to reliably manipulate encrypted traffic. We used this to break TKIP. See our paper for details. An example on how we used it to verify that our awesome-sauce attacks work:

modwifi@ubuntu:~/modwifi/tools$ sudo ./channelmitm -a wlan4 -c wlan5 -j wlan3 -s testnetwork -d mitm.pcap --dual

A-MPDU Injection

You can inject A-MPDUs using ModWifi by adding a special trailer to injected frames. This trailer data will be removed before transmitting the frame to the air. All frames in an A-MPDU except the last must be appended with the trialer b"\x00AGGR". The last frame to be part of the A-MPDU must be appended with the trailer b"\xFFAGGR". For example, to inject an A-MPDU that aggregates three frames in scapy, you should use:

sendp(RadioTap()/Dot11()/Raw(b"\x00AGGR"))
sendp(RadioTap()/Dot11()/Raw(b"\x00AGGR"))
sendp(RadioTap()/Dot11()/Raw(b"\xFFAGGR"))

The firmware will then automatically aggregate these three frames into an A-MPDU. For background, see the function modwifi_txampdu_check.

Troubleshooting

If an attack or device is not working, you can try the following steps to get it working again:

  1. Change the channel of the device. This will reset the wireless chip in the dongle, and perhaps fix the issue.
  2. Bring the device up and down using ifconfig or ip link. This should reset even more settings than just changing the channel.
  3. Unplug the device and plug it back it. This reloads the complete firmware.
  4. If all else fails, reboot your computer.

If you can reproduce a bug, feel free to file a bug report.

Another few remarks when using our tools, and doing wireless hacking in general:

  • You can only change the channel of a monitor device when no other (virtual) interface is active. So if you have a monX interface, you need to bring down (ifconfig wlanX down) all other interfaces (which use that device) first.
  • In general you want to kill other processes that are trying to use/configure your WiFi device. Tools like airmon-zc can help detect which processes might be interfering. Note that airmon-zc is the successor of the older airmon-ng tool.

Installation and Source Code

You can also install the latest drivers and firmware on your own machine. The quickest method is to grab one of our release packages. Only your wireless stack and drivers will be replaced, all other drivers will remain the same (if you use other wifi devices as well, compile them too). Normal usage of WiFi still works perfectly when these drivers are installed (I use these drivers myself :).

The installation instructions are:

mkdir modwifi && cd modwifi
wget https://github.com/vanhoefm/modwifi/raw/master/releases/modwifi-4.4-1.tar.gz
tar -xf modwifi-4.4-1.tar.gz

apt-get install build-essential libncurses-dev bison flex libssl-dev
cd drivers && make defconfig-ath9k-debug
make
sudo make install
cd ..

# Note: the location and name of firmware files on your machine may be different
compgen -G /lib/firmware/ath9k_htc/*backup || for FILE in /lib/firmware/ath9k_htc/*; do sudo cp $FILE ${FILE}_backup; done
sudo cp target_firmware/htc_7010.fw /lib/firmware/ath9k_htc/htc_7010-1.4.0.fw
sudo cp target_firmware/htc_9271.fw /lib/firmware/ath9k_htc/htc_9271-1.4.0.fw

sudo apt-get install g++ libssl-dev libnl-3-dev libnl-genl-3-dev cmake
cd tools && cmake CMakeLists.txt && make all

Reboot so our new drivers will be used. After that you should be good to go. That is, plug in your dongle, and execute the compiled tools.

Note that this only compiles and installs the ath9k drivers. If you want to use modwifi, and at the same time control other wireless networks cards on the kernel, modify and use the appropriate defconfig-* file (e.g. include the appropriate flags in defconfig-ath9k-debug so the drivers you need are also compiled).

If you want to compile the firmware as well, clone the ath9k-htc repository, and follow the instructions there. If you want to modify the driver, you can modify the downloaded code in modwifi-YYYYMMDD.tar.gz. You can put that code in your own repository to keep track of changes, and send us patches based on this. Alternatively, the more correct but also significantly more tedious method, would be to clone the research branch of our forked Linux kernel. The driver can be extracted from the kernel code using the backports project. You can then install the drivers only (so without modifying your own kernel).

Raspberry Pi Support

Our drivers and firmware can be run on a Raspberry Pi. We tested this using raspbian. In order to get it working first download and update some dependencies:

sudo apt-get install linux-image-3.12-1-rpi linux-headers-3.12-1 g++-4.7 iw
sudo update-alternatives --install /usr/bin/g++ g++ /usr/bin/g++-4.7 50

As you can see, we tested this on the 3.12-1-rpi kernel. You can use another kernel if you want, just be sure to download the kernel headers. To enable the 3.12-1-rpi kernel we just downloaded edit /boot/config.txt and append:

kernel=vmlinuz-3.12-1-rpi
initramfs initrd.img-3.12-1-rpi followkernel

And to assure our raspberry pi will recognize the device when we plug it in, execute:

echo "ath9k_htc" | sudo tee -a /etc/modules

Everything is now ready to install our drivers and firmware. Just follow the instructions under section "Installation". Compilation of the drivers can take a while. Finally we have to prevent raspbian from automatically trying to enable and manage WiFi (this interferes with our attacks). First edit /etc/network/interfaces and comment out the following two lines:

#allow-hotplug wlan0
#iface wlan0 inet manual

Now edit /etc/default/ifplugd and change the INTERFACES and HOTPLUG_INTERFACES to:

INTERFACES="eth0"
HOTPLUG_INTERFACES="eth0"
ARGS="-q -f -u0 -d10 -w -I"
SUSPEND_ACTION="stop"

This will prevent raspbian from automatically enabling and managing the wireless interface (so we can first put the device in monitor mode and only then enable it). You can now compile the tools and execute the attacks!

Repositories

The work is divided over several git repositories:

  1. Linux: Forked Linux kernel to make driver modifications.
  2. Backports: Fork of the backports projects so we can backport our drivers to older kernels.
  3. Ath9k-htc: Forked firmware code to implement the core of our attacks.
  4. Tools: New repository for our user-land tools.

You can download all repositories at once using the following commands:

mkdir modwifi && cd modwifi
bash <(curl -s https://raw.githubusercontent.com/vanhoefm/modwifi/master/init.sh)

To compile the Linux and ath9k-htc firmware, read the documentation of these projects. To backport the modified drivers using the backports project, also see the official documentation of that project. Finally, our tools can be compiled using a simple make all. Apart from the tools repositories, all work and modifications are performed on the research branch. When a new Linux kernel (or firmware) is released, we can easily merge with it. As a result our code is relatively easy to keep up-to-date.

For those who also want to start hacking away at the driver and firmware, I recommend first reviewing our patches. This allows you to study what our changes do, and inspect the firmware code at small chunks one at a time. That way it's easier to learn step by step. Maybe you will even find bugs or can make improvements (let us know). Also, in the ath9k-htc repository, there is a directory called docs. While still terse to read, these documents should be an excellent guide while reading and understanding the code.

If you have any questions, don't hesitate to send us a mail.

Supporting new kernels

We rely on the driver backports project to ship our modified drivers (as installable modules) to older kernels. This provides two advantages: (1) the drivers can be installed as modules, meaning user don't have to (re)compile a linux kernel; and (2) these drivers (i.e., modules) are compatible with many recent kernel versions. Officially the backports project tracks the linux-next tree. This means it extracts, and backports, recents drivers (as loadable modules) from the linux-next tree. However, we base our code on Linus' tree, because basing code on linux-next is not really possible.

To target a new kernel there are two cases:

  1. There is a linux-x.y.z branch of the kernel you want to target. Checkout this branch, use it to extract modified drivers. Should be relatively simple.
  2. We need to create our own linux-x.y.z branch. I call my own batches of this type mathy-x.y.z. It is best to first get backports working against a linux-next tag that was tested by the backports project itself. Then I found that, with some minor patches, backports will also work against Linus' tree of a specific version tag that is close to the tested linux-next snapshot. So find the latest linux-next snapshot that is compatible with the backports project. How to get linux-next. You may need to use linux-next-history for this, which contains all linux-next tags ever created. It may be that backports cannot cleanly extract the driver code. If so, crease a new research branch in the backports repository, and modify the patches so everything cleanly applies and compiles.

Use python2 when using backports. Some scripts may fail if python3 is the default.

Note that branches named mathy-x.y.z are custom branches, I personally use them to create backports for my currently running linux kernel. For example, mathy-4.7.y can take code from linux-next, and will compile on Linux 4.7.4. However, it may not compile on older kernels! While working on backports, you may find it useful to use rediff from the patchutils package to manually change patch files.

Publications and Systems Using ModWifi

Below you can find a list papers and systems that either use or build upon ModWifi. They are listed in chronological order.

If you have used or extended ModWifi and would like to have your paper listed here, please open a pull request at https://github.com/vanhoefm/modwifi/pulls or send an email to mathy.vanhoef@kuleuven.be.