Multi-vendor Ansible Modules for Network Automation

You need to perform two steps to start using these modules.

Ensure this repository is in your Ansible module search path
Install Dependencies

Ensure Modules are you in your search path

First, understand what your search path is:

ntc@ntc:~/projects$ ansible --version
ansible 2.1.1.0
  config file = /etc/ansible/ansible.cfg
  configured module search path = ???

If you already have a search path configured, clone the repo (see options below) while you are in your search path.

If you have a "default" or No search path shown, open the config file that is shown in the output above, here that is /etc/ansible/ansible.cfg. In that file, you'll see these first few lines:

[defaults]

# some basic default values...

inventory      = /etc/ansible/hosts
library        = /home/ntc/projects/

Add a path for library - this will become your search path. Validate it with ansible --version after you make the change.

When you clone, do not forget to use --recursive !

Option 1:

git clone https://github.com/networktocode/ntc-ansible --recursive

Option 2:

git clone https://github.com/networktocode/ntc-ansible
cd ntc-ansible
git submodule update --init --recursive

As a quick test and sanity use ansible-doc on one of the modules before trying to use them in a playbook. For example, try this:

$ ansible-doc ntc_file_copy

If that works, Ansible can find the modules and you can proceed to installing the deps below.

Install Dependencies

Option 1:

pip install ntc-ansible

Option 2:

If you already cloned it above, you can just run the third statement below.

git clone https://github.com/networktocode/ntc-ansible
cd ntc-ansible
sudo python setup.py install

Additionally, you'll need lxml can install like this on Ubuntu:

sudo apt-get install zlib1g-dev libxml2-dev libxslt-dev python-dev

Every so often terminal is not installed and it may need to be installed manually:

pip install terminal

Modules

ntc_show_command - gets structured data from devices that don't have an API. This module uses SSH to connect to devices. Supports as many device types as netmiko supports.
ntc_config_command - sends commands to devices that don't have an API. This module uses SSH to connect to devices. Supports as many device types as netmiko supports.
ntc_save_config - saves the running config and optionally copies it to the Ansible control host for an offline backup. Uses SSH/netmiko for IOS, NX-API for Nexus, and eAPI for Arista.
ntc_file_copy - copies a file from the Ansible control host to a network device. Uses SSH for IOS, NX-API for Nexus, and eAPI for Arista.
ntc_reboot - reboots a network device. Uses SSH/netmiko for IOS, NX-API for Nexus, and eAPI for Arista.
ntc_get_facts - gathers facts from a network device. Uses SSH/netmiko for IOS, NX-API for Nexus, and eAPI for Arista.
ntc_rollback - performs two major functions. (1) Creates a checkpoint file or backup running config on box. (2) Rolls back to the previously created checkpoint/backup config. Use case is to create the checkpoint/backup as the first task in a playbook and then rollback to it if needed using block/rescue, i.e. try/except in Ansible. Uses SSH/netmiko for IOS, NX-API for Nexus, and eAPI for Arista.
ntc_install_os - installs a new operating system or just sets boot options. Depends on platform. Does not issue a "reload" command, but the device may perform an automatic reboot. Common workflow is to use ntc_file_copy, ntc_install_os, and then ntc_reboot (if needed) for upgrades. Uses SSH/netmiko for IOS, NX-API for Nexus, and eAPI for Arista.

Examples

See Examples

Background

ntc_show_command and ntc_config_command were the first two modules written out of this group. These two use netmiko for transport - this means if netmiko supports a given platform, these modules can be used.