Subdirectory efm32s2 contains a preliminary OpenOCD flash driver for Silicon Laboratories EFM32 series 2 MCUs, like EFM32PG22, or EFR32FG23, based on OpenOCD's driver for series 0 and 1 MCUs, efm32, which has been adapted as far as necessary for basic functionality. Features other than flashing or debugging, like page locking, may still not work correctly, this hasn't been tested yet.
Some functionality for enabling debug lock and issuing a device reset via DCI to lock/unlock a device has been implemented in efm32s2.cfg, and the tcl will attempt to notify the user if the device is locked. Also this implementation can serve as a good reference for implementing the mechanisms described in SiLabs appnotes AN1303 and AN1190.
A number of details are different in series 2, as compared to series 0 and 1:
- Device Info registers for page, flash and ram sizes are located at different offsets.
- MSC
WRITECMDandADDRBregisters are located at different offsets, which made an adjustment of the flash write assembly code neccessary. - To be able to use the MSC peripheral, its clock must be enabled in the CMU.
- The RAM starts at a different address, 0x2... instead of 0x1....
- Flash base address is not 0x0 but 0x08000000 for EFR32xG23 (but still 0x0 for xG22).
- Debug/device lock/erase has now moved to its own SWD AP called DCI.
Since the work area address (i.e. the start of ram) gets configured in tcl/target/efm32.cfg,
it has been decided to create a new efm32s2 target in tcl/target/efm32s2.cfg,
and to derive a separate flash driver efm32s2.c from efm32.c.
It is not clear yet, if it would make sense to integrate series 2 support into the original efm32 driver,
instead of keeping it separate.
In this project's working directory, run sh setup-openocd-src.sh,
or alternatively, follow these steps:
Clone OpenOCD's official Github mirror repository:
git clone https://github.com/openocd-org/openocd
cd openocd
Checkout a revision compatible to this EFM32 series 2 extension:
git checkout 2e60e2e
... which sets the OpenOCD source directory to where this author last tested building. Bumping further might work, but YMMV.
Initialize submodules:
git submodule init
git submodule update
Still inside the ./openocd subdirectory, copy files from the efm32s2 subdirectory to their positions in the openocd source tree, and apply the patch:
cp ../efm32s2/efm32s2.c src/flash/nor/
cp ../efm32s2/efm32s2.cfg tcl/target/
patch -p1 < ../efm32s2/adjust_openocd.patch
The OpenOCD tree is now ready to be built.
Prerequisites:
make autoconf libtool
gcc git
libusb-dev libftdi-dev
For a minimal setup, with most drivers disabled except CMSIS-DAP and FTDI/MPSSE, run
sh build.sh
If configure complains about missing dependencies, or CMSIS-DAP is not marked yes in the configuration summary, install the missing pieces, and run build.sh again.
If the build succeeded, a minimal installation may be created in the dist subdirectory by running inside this project's working directory:
sh mkdist.sh
To test whether it works, run ident.sh in the dist subdirectory.
A CMSIS-DAP capable device,
connect to the target MCU,
needs to be attached to a local USB port.
The Particle Debugger, for instance,
has worked for debugging using GDB
and flashing without any problems.
cd dist
sh ident.sh
The output should contain lines like:
Info : detected part: PG22C200, rev 17
Info : flash size = 256kbytes
Info : flash page size = 8192bytes
Alternatively, instead of CMSIS-DAP the ftdi driver may be used with an FTDI device with MPSSE mode.
Support has been added for FT232H,
which is part of e.g. UM232H.
To use the ftdi interface in dist/_conf.sh,
comment out the line iface=ftdi_ft232h.
The following wiring has been used successfully with an EFM32PG22 and UM232H:
Note: While the other Pins are connected directly, between TDI and SWDIO a resistor must be placed, as stated in swd-resistor-hack.cfg. For the above setup, 470 Ω has been found to work (while 1 kΩ didn't).
To get the FTDI approach to run on Windows, the default FTDI driver has to be replaced with WinUSB by a tool like zadig.
See the ./windows subdirectory for details.