NANDO (NANDopen) programmer
General
NANDO is open source NAND programmer based on STM32 processor. It supports parallel NAND and SPI flash programming.
PCB boards:
Application:
Features
- USB interface
- PC client software for Linux & Windows.
- TSOP-48 socket adapter for NAND chip (compatible with TL866 adapter)
- TSOP-48 solder adapter for NAND chip
- 8 bit parallel NAND interface
- SPI interface
- 3.3V NAND power supply
- NAND read,write and erase support
- NAND read of chip ID support
- NAND read of bad blocks
- NAND bad block skip option
- NAND include spare area option
- Open KiCad PCB & Schematic
- Open source code
- Read & Write LEDs indication
- Write speed: 512KBytes/s
- Read speed: 640KBytes/s
- Erase speed: 256MBytes/s
- Extendable chip database
- Chip autodetection
- Firmware update
Supported chips
Parallel NAND:
K9F2G08U0C, HY27US08121B, TC58NVG2S3E, F59L2G81A, MX30LF2G18AC and others.
See full list of supported chips qt/nando_parallel_chip_db.csv
SPI flash
AT45DB021D, MX25L8006E, W25Q16JV and others.
See full list of supported chips qt/nando_spi_chip_db.csv
Release binaries
You can download host application deb package for Ubuntu/Windows installer, firmware binary for STM32, schematic and gerber files from here:
https://drive.google.com/drive/folders/1d5hP6MKbkEBGQe_xIRl4-A5LPt_-9QIN
License
In general the sorce code, PCB and schematic are under GPLv3 license but with limitations of:
firmware/libs/spl/CMSIS/License.doc
firmware/libs/spl/STM32_USB-FS-Device_Driver/ - http://www.st.com/software_license_agreement_liberty_v2
firmware/usb_cdc - http://www.st.com/software_license_agreement_liberty_v2
Build
Requirements
Linux based OS
Build firmware
- Download compiler and documents from Google Drive:
- Go to https://drive.google.com/drive/folders/1zLtebfLW6CxaWMq0rr4EfEPmeXfGk-7n?usp=sharing
- Press "Download All"
- mkdir ~/dev/
- cd ~/dev/
- mv ~/Downloads/nand_programmer*.zip ./
- unzip nand_programmer-*.zip
- cd nand_programmer/compiler/
- tar -xvf gcc-arm-none-eabi-4_9-2015q1-20150306-linux.tar.bz2
- cd ..
- git clone https://github.com/bbogush/nand_programmer.git
- cd nand_programmer/firmware
- make
Burn firmware via SWD (ST-Link)
- sudo apt-get install libusb-1.0-0-dev
- cd ~/dev/
- git clone https://github.com/texane/stlink.git
- cd stlink/
- mkdir -p build && cd build
- cmake -DCMAKE_BUILD_TYPE=Release ..
- sudo make install
- sudo cp ../etc/udev/rules.d/* /etc/udev/rules.d/
- sudo udevadm control --reload-rules
- sudo udevadm trigger
- connect ST-Link to board
- cd ~/dev/nand_programmer/nand_programmer/firmware
- st-flash write ./obj/prog.bin 0x8000000
Build host application
Linux
- sudo apt-get install libboost-all-dev
- Install Qt5.x
- Open ~/dev/nand_programmer/nand_programmer/qt/qt.pro with QtCreator.
- Go to Projects->Build->Build Steps->Add Build Step->Make. Add "install" to "Make arguments".
- Build->Run qmake
- Build->Build All
- Build->Run
Windows
- Install boost library from GoogleDriver archive under C:/boost/ or compile.
- Install Qt5.x
- Open ~/dev/nand_programmer/nand_programmer/qt/qt.pro with QtCreator.
- Go to Projects->Build->Build Steps->Add Build Step->Make. Add "install" to "Make arguments".
- Build->Run qmake
- Build->Build All
- Build->Run
Schematic and PCB
- Install KiCad 5.0.1
- Open ~/dev/nand_programmer/nand_programmer/kicad/nand_programmator.pro
Adding new chip
- Go to Settings->Chip database
- Press "+" button and fill out parameters from datasheet.
WiKi
Check WiKi page for more information.