/oldFRENSIE

Framework for REsearch in Nuclear ScIence and Engineering

Primary LanguageC++OtherNOASSERTION

Installation {#installation}

Dependencies

To promote rapid scientific software development and research, FRENSIE is built off of a large number of software libraries. The software libraries that FRENSIE depends on are listed below.

  1. OpenMPI 1.8.2+ - optional
  2. HDF5 1.8.13+ - optional
  3. Python 2.7+
  4. Numpy 1.8+
  5. SWIG 4.0+
  6. Boost 1.72.0+
  7. MOAB 5.0 - optional
  8. DagMC 2.8+ - optional
  9. ROOT 6.04/02+ - optional

Note that OpenMPI is only required if you plan on running FRENSIE on a distributed memory system. HDF5 is only required if you plan on exporting internal FRENSIE data in the 'h5fa' format or if you plan on installing MOAB. MOAB is required if you plan on using tetrahedral meshes with FRENSIE or if you plan on exporting hexahedral mesh data. If you plan on using CAD geometries for particle simulations you will need both DagMC and MOAB (to process the CAD geometries into the required 'h5m' format you will need Trelis). ROOT geometries can also be used for particle simulations if the ROOT package is built. Because users interact with FRENSIE through Python, the Python, Numpy and SWIG packages, are all required. Building FRENSIE without the optional packages will result in faster build times which can be useful for certain development tasks.

Several of the above software libraries will be built from source. Others can be installed using your system's package manager. This process will be described in the next sections.

Additional Software

  1. GNU compiler (g++ 6.0+)
  2. CMake 3.17.1+
  3. git 2.14+
  4. Doxygen 1.8.6+ - optional
  5. Trelis 16.3 - optional

FRENSIE requires a GNU compiler (6.0 or greater), CMake (3.0.1 or greater) and git (1.9.1 or greater) to build correctly. If you plan on building the FRENSIE documentation, Doxygen (1.8.6 or greater) is also required.

Trelis is used to process a CAD geometry into the 'h5m' format required by the DagMC package. Once you have obtained a license for Trelis, a useful installation guide can be found here.

Building Dependent Software Libraries

Before any of the software libraries are built, verify that the system has CMake version 3.17.1 or greater installed. If CMake is not installed or an older version is present, build CMake using the instructions below.

When building software libraries and executables from source, the following directory structure should be adopted: software/package/package.xx.xx.xx, software/package/build, software/package/src. "package" will be the name of the particular software package. "package.xx.xx.xx" comes from unpacking the compressed source files (e.g. package.tar.gz). The src directory is created by making a softlink to the package.xx.xx.xx directory. This is done to make the build a bit easier.

Please note that the software libraries should be built in the order that they are described.

Checking out FRENSIE

  1. create a working directory where FRENSIE will be built (e.g. software/frensie)
  2. move to the frensie directory
  3. run git clone git@github.com:FRENSIE/FRENSIE.git
  4. run ln -s FRENSIE src

Building Git

  1. run sudo apt-get install git

Building CMake

Basic:

  1. run sudo apt-get install cmake
  2. run cmake --version and verify that the output is >= 3.17.1. If the output is less than 3.17.1 proceed to the advanced build instructions

Advanced:

  1. download the latest source release CMake 3.17.1+ source
  2. move the cmake-3.x.tar.gz file to the cmake directory (e.g. software/cmake)
  3. move to the cmake directory
  4. run tar -xvf cmake-3.x.tar.gz
  5. run ln -s cmake-x src
  6. run mkdir build
  7. move to the build directory (e.g. software/cmake/build)
  8. run ../src/configure --prefix=absolute-path-to_software/cmake
  9. run make -j n, where n is the number of threads to use while building
  10. run make test
  11. run make install
  12. add the following line to the .bashrc file: export PATH=absolute-path-to_software/cmake/bin:$PATH
  13. run exec bash
  14. run cmake --version and verify that the output is 3.x

Building Doxygen - optional

Basic:

  1. run sudo apt-get install doxygen
  2. run doxygen --version and verify that the output is >= 1.8.6

Advanced:

  1. download the Doxygen 1.8.8 source
  2. move the doxygen-1.8.8.src.tar.gz file to the doxygen directory (e.g. software/doxygen)
  3. move to the doxygen directory
  4. run tar -xvf doxygen-1.8.8.src.tar.gz
  5. move to the doxygen-1.8.8 directory
  6. run ./configure --prefix=absolute-path-to_software/doxygen
  7. run make -j n
  8. run make test
  9. run make install
  10. add the following line to the .bashrc file: export PATH=absolute-path-to_software/doxygen/bin:$PATH
  11. run exec bash

Building Open MPI - optional

Basic:

  1. run sudo apt-get install openmpi-bin libopenmpi-dev
  2. run mpiexec --version and verify that the output is >= 1.6.5

Advanced:

  1. download the Open MPI 1.8.2 source
  2. move the openmpi-1.8.2.tar.gz file to the mpi directory (e.g. software/mpi)
  3. move to the mpi directory
  4. run tar -xvf openmpi-1.8.2.tar.gz
  5. run ln -s openmpi-1.8.2 src
  6. run mkdir build
  7. move to the build directory (e.g. software/mpi/build)
  8. run ../src/configure --prefix=absolute-path-to_software/mpi
  9. run make -j n
  10. run make check
  11. run make install
  12. add the following line to the .bashrc file: export PATH=absolute-path-to_software/mpi/bin:$PATH
  13. add the following line to the .bashrc file: export LD_LIBRARY_PATH=absolute-path-to_software/mpi/lib:$LD_LIBRARY_PATH
  14. run exec bash

Building HDF5 - optional

Basic:

  1. run sudo apt-get install hdf5-tools libhdf5-dev
  2. run h5ls --version and verify that the output is >= 1.8.11

Advanced:

  1. download the HDF5 1.8.13 source
  2. move the hdf5-1.8.13.tar.gz file to the hdf5 directory (e.g. software/hdf5)
  3. move to the hdf5 directory
  4. run tar -xvf hdf5-1.8.13.tar.gz
  5. run ln -s hdf5-1.8.13 src
  6. run mkdir build
  7. move to the build directory (e.g. software/hdf5/build)
  8. run ../src/configure --enable-optimized --enable-shared --enable-cxx --enable-hl --disable-debug --prefix=absolute-path-to_software/hdf5
  9. run make -j n
  10. run make test
  11. run make install
  12. add the following line to the .bashrc file: export PATH=absolute-path-to_software/hdf5/bin:$PATH
  13. add the following line to the .bashrc file: export LD_LIBRARY_PATH=absolute-path-to_software/hdf5/lib:$LD_LIBRARY_PATH
  14. run exec bash

Building Python and NumPy

  1. run sudo apt-get install python python-dev python-numpy

Building SWIG

Basic:

  1. run sudo apt-get install swig
  2. run swig -version and verify that the output is >= 4.0

Advanced

  1. create a swig directory (e.g. software/swig)
  2. move to the swig directory
  3. run git clone git@github.com:swig/swig.git
  4. run ln -s swig src
  5. run mkdir build
  6. move to the build directory (e.g. software/swig/build)
  7. run ../src/configure --prefix=absolute-path-to_software/swig
  8. run make -j n
  9. run make install
  10. add the following line to the .bashrc file: export PATH=absolute-path-to_software/swig/bin:$PATH

Building Boost

Basic:

  1. run sudo apt-get install libboost-all-dev

Advanced:

  1. download the Boost 1.72.0 source
  2. move the boost_1_72_0.tar.gz file to the boost directory (e.g. software/boost)
  3. move to the boost directory
  4. run tar -xvf boost_1_72_0.tar.gz
  5. move to the boost_1_72_0 directory (e.g. software/boost/boost_1_72_0)
  6. run ./bootstrap.sh --prefix=absolute-path-to_software/boost
  7. if OpenMPI has been built, run sed -i "$ a using mpi ;" project-config.jam
  8. run ./b2 -jn --prefix=absolute-path-to_software/boost -s NO_BZIP2=1 link=shared runtime-link=shared install, where n is the number of threads to use while building
  9. add the following line to the .bashrc file: export LD_LIBRARY_PATH=absolute-path-to_software/boost/lib:$LD_LIBRARY_PATH
  10. run exec bash

Building MOAB - optional

  1. create a moab directory (e.g. software/moab)
  2. move to the moab directory
  3. run git clone https://bitbucket.org/aprobinson/moab.git
  4. move to the moab directory (e.g. software/moab/moab)
  5. run git checkout Version5.1.0
  6. run autoreconf -fi
  7. move up a directory (e.g. software/moab)
  8. run ln -s moab src
  9. run mkdir build
  10. move to the build directory (e.g. software/moab/build)
  11. run sudo apt-get install libeigen3-dev
  • Basic HDF5 Build:
    • run ../src/configure --enable-optimize --enable-shared --disable-debug --with-hdf5 --prefix=absolute-path-to_software/moab/
  • Advanced HDF5 Build:
    • run ../src/configure --enable-optimize --enable-shared --disable-debug --with-hdf5=absolute-path-to_software/hdf5 --prefix=absolute-path-to_software/moab/
  1. run make -j n
  2. run make check
  3. run make install
  4. add the following line to the .bashrc file: export PATH=absolute-path-to_software/moab/bin:$PATH
  5. add the following line to the .bashrc file: export LD_LIBRARY_PATH=absolute-path-to_software/moab/lib:$LD_LIBRARY_PATH
  6. run exec bash

Building DagMC - optional

  1. create a dagmc directory (e.g. software/dagmc)
  2. move to the dagmc directory
  3. run git clone https://github.com/FRENSIE/DAGMC.git
  4. move to the DAGMC directory (e.g. software/dagmc/DAGMC)
  5. run git checkout develop
  6. move up a directory (e.g. software/dagmc)
  7. run ln -s DAGMC src
  8. run mkdir build
  9. move to the build directory (e.g. software/dagmc/build)
  10. if HDF5 was built from source, run env HDF5_ROOT=absolute-path-to_software/hdf5
  11. run cmake ../src -DCMAKE_INSTALL_PREFIX=absolute-path-to_software/dagmc -DCMAKE_BUILD_TYPE:STRING=Release -DMOAB_DIR=absolute-path-to_software/moab
  12. run make -j n
  13. run make install
  14. add the following line to the .bashrc file: export PATH=absolute-path-to_software/dagmc/bin:$PATH
  15. add the following line to the .bashrc file: export LD_LIBRARY_PATH=absolute-path-to_software/dagmc/lib:$LD_LIBRARY_PATH
  16. run exec bash

Building ROOT - optional

Basic:

  1. download the appropriate ROOT 6.04/02 binaries
  2. move the binary file to the software directory (e.g. software)
  3. run tar -xvf root_v6.04.02* - Note: This will create a directory called root.
  4. add the following line to the .bashrc file: export PATH=absolute-path-to_software/root/bin:$PATH
  5. add the following line to the .bashrc file: export LD_LIBRARY_PATH=absolute-path-to_software/root/lib:$LD_LIBRARY_PATH

If you are using g++ 5.3+ these precompiled binaries will no longer work (using the root executable will result in an error). Use the advanced build instructions below instead.

Advanced:

  1. download the ROOT 6.04/16 source
  2. move the root_v6.04.16.source.tar.gz file to the root directory (e.g. software/root)
  3. move to the root directory
  4. run tar -xvf root_v6.04.16.source.tar.gz
  5. run ln -s root_v6.04.16 src
  6. run mkdir build
  7. move to the build directory (e.g. software/root/build)
  8. copy FRENSIE/scripts/root.sh into the build directory
  9. change the variables in the script to reflect the desired system paths
  10. run sudo apt-get install libx11-dev libxpm-dev libxft-dev libxext-dev
  11. run ./root.sh
  12. run make -j n
  13. run make install
  14. add the following line to the .bashrc file: export PATH=absolute-path-to_software/root/bin:$PATH
  15. add the following line to the .bashrc file: export LD_LIBRARY_PATH=absolute-path-to_software/root/lib:$LD_LIBRARY_PATH

Building FRENSIE

At this point all of the dependent software libraries should have been built. If any errors were encountered do not try to proceed to building FRENSIE. If no errors were encountered, follow the instructions below.

  1. move to the frensie working directory - not the repo itself (e.g. software/frensie)
  2. run mkdir build
  3. move to the build directory (e.g. software/frensie/build)
  4. copy the FRENSIE/scripts/frensie.sh
  5. change the variables in the script to reflect the desired system paths (if the basic build instructions where use for a package the PACKAGE_PREFIX variable can be left blank in the script).
  6. run ./frensie.sh to configure FRENSIE
  7. run make -j n
  8. run make test
  9. run make manual
  10. run make install
  11. add the following line to the .bashrc file: export PATH=absolute-path-to_software/frensie/bin:$PATH
  12. add the following line to the .bashrc file: export PYTHONPATH=absolute-path-to_software/frensie/bin:$PYTHONPATH
  13. add the following line to the .bashrc file: export PYTHONPATH=absolute-path-to_software/frensie/lib/python2.7/site-packages:$PYTHONPATH

Note 1: There are several other configure options that can be changed in the frensie.sh script:

  • -D FRENSIE_ENABLE_DBC:BOOL=OFF turns off very thorough Design-by-Contract checks (commonly done with release builds).
  • -D FRENSIE_ENABLE_PROFILING:BOOL=ON enables profiling (only in debug builds).
  • -D FRENSIE_ENABLE_CONVERAGE:BOOL=ON enables coverage testing (only in debug builds).
  • -D FRENSIE_ENABLE_OPENMP:BOOL=OFF disables OpenMP thread support.
  • -D FRENSIE_ENABLE_MPI:BOOL=ON enables MPI support.
  • -D FRENSIE_ENABLE_HDF5:BOOL=ON enables HDF5 support.
  • -D FRENSIE_ENABLE_MOAB:BOOL=ON enables MOAB support.
  • -D FRENSIE_ENABLE_DAGMC:BOOL=ON enables the DagMC geometry interfaces.
  • -D FRENSIE_ENABLE_ROOT:BOOL=ON enables the ROOT geometry interfaces.
  • -D FRENSIE_ENABLE_COLOR_OUTPUT:BOOL=OFF disables color output in TTY shells.
  • -D FRENSIE_ENABLE_EXPLICIT_TEMPLATE_INST:BOOL=OFF disables explicit template instantiation. Build times will be shorter when this is enabled.
  • -D FRENSIE_ENABLE_MANUAL:BOOL=OFF prevents the user from building the FRENSIE manual using Doxygen (useful if Doxygen is not available).

Note 2: To help the build system locate packages in non-standard locations, the following CMake variables can be set:

  • -D DOXYGEN_PREFIX:PATH=path-to-doxygen-install-dir indicates where the doxygen install directory is located. If your system already has Doxygen 1.8.2 or above, there is no need to install version 1.8.8 and this option can be deleted from the frensie.sh script.
  • -D MPI_PREFIX:PATH=path-to-mpi-install-dir indicates where the custom MPI install directory is located.
  • -D HDF5_PREFIX:PATH=path-to-hdf5-install-dir indicates where the custom HDF5 install directory is located.
  • -D SWIG_PREFIX:PATH=path-to-swig-install-dir indicates where the custom SWIG install directory is located.
  • -D BOOST_PREFIX:PATH=path-to-boost-install-dir indicates where the custom Boost install directory is located.
  • -D MOAB_PREFIX:PATH=path-to-moab-install-dir indicates where the custom MOAB install directory is located.
  • -D DAGMC_PREFIX:PATH=path-to-dagmc-install-dir indicates where the custom DAGMC install directory is located.
  • -D ROOT_PREFIX:PATH=path-to-root-install-dir indicates where the custom ROOT install directory is located.
  • -D BUILDNAME_PREFIX:STRING=my-build-name sets the custom build name that will be displayed on the CDash dashboard (only used when FRENSIE_ENABLE_DASHBOARD_CLIENT is set to ON).
  • -D XSDIR_DIR:PATH=path-to-mcnp-data indicates where the nuclear data used by MCNP6 is located on the system (specifically, where the desired xsdir file is located).

Note 3: Each FRENSIE package has a custom build target, a custom test build target and a custom test run target. For a given package PACKAGE the three targets will have the following names:

  1. PACKAGE,
  2. PACKAGE_tests,
  3. test-PACKAGE. If you want to build the utility_core package, you would run make utility_core or make -j8 utility_core. If you want to build all of the utility_core package tests, you would run make utility_core_tests or make -j8 utility_core_tests. Once the package tests have been built you can run the tests by running make test-utility_core.

FRENSIE has the following packages:

  • utility_core
  • utility_mpi
  • utility_archive
  • utility_system
  • utility_prng
  • utility_interpolation
  • utility_grid
  • utility_distribution
  • utility_stats
  • utility_integrator
  • utility_mesh
  • geometry_core
  • geometry_dagmc (if DagMC is enabled)
  • geometry_root (if ROOT is enabled)
  • data_core
  • data_ace
  • data_endf
  • data_endl
  • data_native
  • data_database
  • data_xsdir
  • monte_carlo_core
  • monte_carlo_collision_core
  • monte_carlo_collisoin_photon
  • monte_carlo_collision_electron
  • monte_carlo_collision_neutron
  • monte_carlo_collision_kernel
  • monte_carlo_active_region_core
  • monte_carlo_active_region_response
  • monte_carlo_active_region_source
  • monte_carlo_event_core
  • monte_carlo_event_estimator
  • monte_carlo_event_particle_tracker
  • monte_carlo_event_forced_collisions
  • monte_carlo_event_weight_windows
  • monte_carlo_event_dispatcher
  • monte_carlo_manager
  • data_gen_endl
  • data_gen_electron_photon
  • data_gen_free_gas_sab
  • pyfrensie

Note 4: The FRENSIE manual is generated using doxygen (using the make manual command). After running make install, a link to the manual will be placed in the doc directory of the install directory. This manual must be opened in your web browser of choice (e.g. google-chrome manual.html).

Running FRENSIE

Before running FRENSIE, a database must be generated. This database is used by FRENSIE to load the various data files requested by the user (it functions in a similar way to the MCNP xsdir file). Simply run generate_database.sh to generate the database.

Once the database has been generated, review the example problems and the manual. Additional example problems can be found at frensie-tests.

Dashboard

The dashboard is not currently active - the following comments have been kept in the event that the dashboard is reactivated again in the future.

A private dashboard has been set up for developers. Please register with the dashboard and send an email to Alex Robinson indicating that you would like to have access to the dashboard.

To set up a dashboard client, simply set the dashboard client setup configure option to on (e.g. -D SETUP_DASHBOARD_CLIENT:BOOL=ON). This will add three new make targets: make Experimental, make Nightly and make Continuous. The experimental target should be used to test that the client has been set up correctly. The nightly and continuous targets can be executed on the client machine at regular intervals using cron and crontab (if on a Linux system). However, it is recommended that these targets are never used and instead the shell scripts frensie-run-nightly.sh and frensie-run-ci.sh (found in the scripts directory) are used. Because cron only loads a few environment variables when it executes commands, it is necessary to write shell scripts that load the necessary environment variables, which is what the two scripts do.

Before setting up the crontab entries, a separate frensie build should be created (following the steps above) for nightly builds (e.g. software/frensie-nightly) and for continuous builds (e.g. software/frensie-ci, if a continuous integration system is desired). Once those builds have been completed, the crontab entries can be created by executing crontab -e. This will open up the table with the default text editor. At the bottom of this file, add the following lines:

  • 0 1 * * * abs-path-to-nightly-build-dir/frensie-run-nightly.sh
  • */5 * * * * abs-path-to-ci-build-dir/frensie-run-ci.sh

The second line can be omitted if the client will only do nightly builds. Note that the first line tells cron to run the nightly script every day at 1:00 AM. The second line tells cron to run the ci script every 5 minutes (if no changes to the master branch have occurred nothing happens).