Subsocks

A Socks5 proxy that encapsulates Socks5 in other security protocols

Introduction

Subsocks is a secure Socks5 proxy. It encapsulate Socks5 in other security protocols such as HTTPS and Websocket instead of using Socks5 directly. Socks5 is fully supported (Connect, Bind, UDP associate), and extending Socks5 to make UDP over TCP possible. It helps you optimize your network or bypass firewalls that only allow some particular protocols.

Installation

go get

Subsocks is written by Go, If you have Go environment, using go get is one of the easiest ways.

go get github.com/luyuhuang/subsocks

Docker

docker pull luyuhuang/subsocks

Binary file

Download the binary file from the release page.

Build from source code

You can also build from source code.

git clone https://github.com/luyuhuang/subsocks.git
cd subsocks
go build

Usage

Getting started

A Subsocks instance may be a client or a server, determined by the configuration. A Subsocks client receives Socks5 data from Apps and encapsulate Socks5 data into a security protocol like HTTPS, then forward it to the Subsocks server. The Subsocks server unpacks the data from the client and accesses the internet.

Create the client configuration file cli.toml with the following content:

[client]
listen = "127.0.0.1:1030"

server.protocol = "https"
server.address = "SERVER_IP:1080" # replace SERVER_IP with the server IP

http.path = "/proxy" # same as http.path of the server
tls.skip_verify = true # skip verify the server's certificate since the certificate is self-signed

Then start the client:

subsocks -c cli.toml

Similarity, create the server configuration file ser.toml:

[server]
listen = "0.0.0.0:1080"
protocol = "https"

http.path = "/proxy"

And then start the server:

subsocks -c ser.toml

With Docker

Download docker-compose.yml:

wget https://raw.githubusercontent.com/luyuhuang/subsocks/master/docker-compose.yml

Create the configuration file config.toml:

[server] # no one will use docker for the client, right?

# must be "0.0.0.0:1080". It's just the address in the
# container, modify the real address in docker-compose.yml
listen = "0.0.0.0:1080"

protocol = "https"
# other fields ...

Launch:

docker-compose up -d

NOTICE: If you want to use a custom certificate, edit docker-compose.yml and create a volume to map it to the container.

Configuration

Subsocks configuration format is TOML, which is easy and obvious.

Client configuration

The client configuration format is as follows:

[client] # client configuration

listen = "127.0.0.1:10030"

username = "admin"
password = "123456"

server.protocol = "wss"
server.address = "10.1.1.1:443"

http.path = "/proxy"

ws.path = "/proxy"

tls.skip_verify = false
tls.ca = "server.crt"

Basic fields

listen: string, the client socks5/http listening address.
username, password: string, username and password used to connect to the server.
server.protocol: string, protocol of the server, the value may be:
- socks: pure socks5;
- http, https: HTTP and HTTPS;
- ws, wss: Websocket and Websocket Secure.
server.address: string, address of the server.

HTTP

If server.protocol is http or https, http.* is enabled.

http.path: string, HTTP request path. Default /.

Websocket

If server.protocol is ws or wss, ws.* is enabled.

ws.path: string, Websocket handshake path. Default /.

TLS/SSL

If the protocol is over TLS, i.e. server.protocol is https or wss, tls.* is enabled.

tls.skip_verify: boolean, skip verifying the server's certificate if the value is true. Default false. It's not safe to skip verifying the certificate, if the server's certificate is self-signed, please set tls.ca to verify the certificate.
tls.ca: string, a certificate file name. It's optional. If set, Subsocks will use the specific CA certificate to verify the server's certificate.

Smart Proxy

If there is a rules field, enable smart proxy. Smart proxy is only available for the Connect method since we don't know the real peer when using Bind or UDP Associate. There are two ways to configure proxy rules. One is setting the rules field to a table containing proxy rules:

[client.rules]
"www.twitter.com" = "P"
"*.github.com" = "D"
"8.8.8.8" = "P"
"1.0.1.0/24" = "D"
"2001:db8::/32" = "P"

"*" = "A"

Each pair in the table is a rule. The left side of = is the address, which can be:

Domain, a wildcard * indicates all subdomains of the domain;
IP and CIDR;
A single wildcard * represents all other addresses.

The right side of = is the rule, which can be:

P, proxy: always via the server;
D, direct: always direct connect;
A, auto: automatic detection, proxy if the direct connection fails.

Another way is using a separate file to configure rules and set the rules field to a string representing the file name:

rules = "rules.txt"

The contents of rules.txt are as follows:

www.twitter.com     P
8.8.8.8
2001:db8::/32

*.github.com        D
1.0.1.0/24

# all others is automatic detection
*   A

Each line is a rule, except empty lines and comment lines(starting with #). Each line contains an address and an optional rule, separated by several spaces. If a line doesn't have a rule, its rule is the same as the previous line.

Authorization

If there is a users field, then enable authorization. In this case, applications that use proxy via the client must be authorized. There are two ways to configure the user list. One is using the htpasswd file, setting the user field to a string indicating the htpasswd file name:

users = "passfile"

Another way is configuring username-password pairs directly. Setting the users field to a table containing username-password pairs:

[client.users]
"admin" = "123456"
"guest" = "abcdef"

Server configuration

The server configuration format is as follows:

[server] # server configuration

protocol = "wss"
listen = "0.0.0.0:443"

http.path = "/proxy"

ws.path = "/proxy"
ws.compress = true

tls.cert = "server.crt"
tls.key = "server.key"

Basic fields

protocol: string, protocol of the server. Same as the server.protocol field of the client.
listen: string, the server listening address.

HTTP

If protocol is http or https, http.* is enabled.

http.path: string, HTTP request path. Default /.

Websocket

If protocol is ws or wss, ws.* is enabled.

ws.path: string, Websocket handshake path. Default /.
ws.compress: boolean, whether to enable compression. Default false.

TLS/SSL

If the protocol is over TLS, i.e. protocol is https or wss, tls.* is enabled.

tls.cert: string, certificate file name.
tls.key: string, key file name.

If tls.cert or tls.key is not set, key and certificate will be automatically generated.

Authorization

If there is a users field, then enable authorization. This means the client must use its username and password for authorization. Configuration of server.users is the same as client.users.