/.dotfiles

Primary LanguageShell

https://www.atlassian.com/git/tutorials/dotfiles

Recently I read about this amazing technique in an Hacker News thread on people's solutions to store their dotfiles. User StreakyCobra showed his elegant setup and ... It made so much sense! I am in the process of switching my own system to the same technique. The only pre-requisite is to install Git.

In his words the technique below requires:

No extra tooling, no symlinks, files are tracked on a version control system, you can use different branches for different computers, you can replicate you configuration easily on new installation.

The technique consists in storing a Git bare repository in a "side" folder (like $HOME/.dotfiles or $HOME/.myconfig) using a specially crafted alias so that commands are run against that repository and not the usual .git local folder, which would interfere with any other Git repositories around.

Starting from scratch

If you haven't been tracking your configurations in a Git repository before, you can start using this technique easily with these lines:

git init --bare $HOME/.dotfiles
alias dotfiles='/usr/bin/git --git-dir=$HOME/.dotfiles/ --work-tree=$HOME'
dotfiles config --local status.showUntrackedFiles no
dotfiles update-index --assume-unchanged README.md
echo "alias dotfiles='/usr/bin/git --git-dir=$HOME/.dotfiles/ --work-tree=$HOME'" >> $HOME/.bashrc
  • The first line creates a folder ~/.dotfiles which is a Git bare repository that will track our files.
  • Then we create an alias "dotfiles" which we will use instead of the regular git when we want to interact with our configuration repository.
  • We set a flag - local to the repository - to hide files we are not explicitly tracking yet. This is so that when you type dotfiles status and other commands later, files you are not interested in tracking will not show up as untracked.
  • Also you can add the alias definition by hand to your .bashrc or use the the fourth line provided for convenience. I packaged the above lines into a snippet up on Bitbucket and linked it from a short-url. So that you can set things up with:
curl -Lks http://bit.do/cfg-init | /bin/bash

After you've executed the setup any file within the $HOME folder can be versioned with normal commands, replacing git with your newly created dotfiles alias, like:

dotfiles status
dotfiles add .vimrc
dotfiles commit -m "Add vimrc"
dotfiles add .bashrc
dotfiles commit -m "Add bashrc"
dotfiles push

Install your dotfiles onto a new system (or migrate to this setup)

If you already store your configuration/dotfiles in a Git repository, on a new system you can migrate to this setup with the following steps:

  • And that your source repository ignores the folder where you'll clone it, so that you don't create weird recursion problems:
echo ".dotfiles" >> .gitignore
  • Now clone your dotfiles into a bare repository in a "dot" folder of your $HOME:
git clone --bare <git-repo-SSH-url> $HOME/.dotfiles
  • Define the alias in the current shell scope:
alias dotfiles='/usr/bin/git --git-dir=$HOME/.dotfiles/ --work-tree=$HOME'
  • Checkout the actual content from the bare repository to your $HOME:
dotfiles checkout
  • The step above might fail with a message like:
error: The following untracked working tree files would be overwritten by checkout:
    .bashrc
    .gitignore
Please move or remove them before you can switch branches.
Aborting

This is because your $HOME folder might already have some stock configuration files which would be overwritten by Git. The solution is simple: back up the files if you care about them, remove them if you don't care. I provide you with a possible rough shortcut to move all the offending files automatically to a backup folder:

mkdir -p .config-backup && \
dotfiles checkout 2>&1 | egrep "\s+\." | awk {'print $1'} | \
xargs -I{} mv {} .config-backup/{}
  • Re-run the check out if you had problems:
dotfiles checkout
  • Set the flag showUntrackedFiles to no on this specific (local) repository:
dotfiles config --local status.showUntrackedFiles no
  • Remove README.md so it doesn't pollute our home directory and ignore changes so it doesn't annoy us:
rm ~/README.md
dotfiles update-index --assume-unchanged README.md
  • You're done, from now on you can now type config commands to add and update your dotfiles:
dotfiles status
dotfiles add .vimrc
dotfiles commit -m "Add vimrc"
dotfiles add .bashrc
dotfiles commit -m "Add bashrc"
dotfiles push

Again as a shortcut not to have to remember all these steps on any new machine you want to setup, you can create a simple script, store it as Bitbucket snippet like I did, create a short url for it and call it like this:

curl -Lks http://bit.do/cfg-install | /bin/bash

For completeness this is what I ended up with (tested on many freshly minted Alpine Linux containers to test it out):

git clone --bare https://bitbucket.org/durdn/cfg.git $HOME/.cfg
function config {
   /usr/bin/git --git-dir=$HOME/.cfg/ --work-tree=$HOME $@
}
mkdir -p .config-backup
config checkout
if [ $? = 0 ]; then
  echo "Checked out config.";
  else
    echo "Backing up pre-existing dot files.";
    config checkout 2>&1 | egrep "\s+\." | awk {'print $1'} | xargs -I{} mv {} .config-backup/{}
fi;
config checkout
config config status.showUntrackedFiles no