mccloudaero/evpr

Issues

• DUT13 Test Log

  #105 opened 3 years ago by GeorgesOatesLarsen
  0

• Get better connectors for programmer board

  #104 opened 3 years ago by GeorgesOatesLarsen
  0

• Shimless pasting plate

  #103 opened 3 years ago by GeorgesOatesLarsen
  0

• Add encryption to broadcast protocol

  #82 opened 3 years ago by GeorgesOatesLarsen
  2

• Add Reflow profiles to electronics/fabrication folder

  #93 opened 3 years ago by GeorgesOatesLarsen
  3

• Osh Park did not cut tab separation geometry

  #79 opened 3 years ago by GeorgesOatesLarsen
  3

• DUT10 Testing Log

  #88 opened 3 years ago by GeorgesOatesLarsen
  3

• DUT9 Testing Log (and some notes on STILTS)

  #86 opened 3 years ago by GeorgesOatesLarsen
  11

• Improve Low-Temperature reflow process

  #91 opened 3 years ago by GeorgesOatesLarsen
  2

• Add hole positions to info folder

  #95 opened 3 years ago by GeorgesOatesLarsen
  1

• Adjust solder mask dot for U.DS2 to be more visible even when pasted (currently, paste obscures it)

  #96 opened 3 years ago by GeorgesOatesLarsen
  1

• Adjust Q.YY1 paste profile

  #97 opened 3 years ago by GeorgesOatesLarsen
  1

• Current brush board shows signs of catastrophic wear

  #101 opened 3 years ago by GeorgesOatesLarsen
  2

• Magnet for RPM sensing

  #100 opened 3 years ago by petermccloud
  3

• Project Managment Items

  #87 opened 3 years ago by GeorgesOatesLarsen
  0

• Hall-Effect Tachometer

  #102 opened 3 years ago by GeorgesOatesLarsen
  1

• DUT12 Test Log

  #99 opened 3 years ago by GeorgesOatesLarsen
  0

• DUT 11 Test Log

  #98 opened 3 years ago by GeorgesOatesLarsen
  0

• Create documentation for communications protocol once finalized

  #94 opened 3 years ago by GeorgesOatesLarsen
  0

• Develop SOP for all boards

  #92 opened 3 years ago by GeorgesOatesLarsen
  0

• Increase low-temp soak time by 20 seconds

  #65 opened 3 years ago by GeorgesOatesLarsen
  1

• Minimal WiFi/ESPNOW initialization

  #83 opened 3 years ago by GeorgesOatesLarsen
  4

• Redesign pasting holder, order board shims from Osh

  #64 opened 3 years ago by GeorgesOatesLarsen
  1

• Fix internal layer floods

  #70 opened 3 years ago by GeorgesOatesLarsen
  1

• Q.YY2 orientation is non-obvious

  #72 opened 3 years ago by GeorgesOatesLarsen
  1

• Add some excess exposed copper on traces around borders of all fine-pitch components

  #62 opened 3 years ago by GeorgesOatesLarsen
  2

• Order/set up zero-ohm resistors as placeholders for compliance resistors

  #67 opened 3 years ago by GeorgesOatesLarsen
  1

• EVPR automated testbench?

  #90 opened 3 years ago by GeorgesOatesLarsen
  0

• Formalize component placement diagram and, in general, the assembly procedure

  #89 opened 3 years ago by GeorgesOatesLarsen
  0

• D.ZZ1 will bleed battery power

  #73 opened 3 years ago by GeorgesOatesLarsen
  1

• DUT7/8 Testing Log

  #78 opened 3 years ago by GeorgesOatesLarsen
  2

• Tab separation slots could be closer together

  #80 opened 3 years ago by GeorgesOatesLarsen
  1

• Detailed characterization of USB Flashing Issues

  #76 opened 3 years ago by GeorgesOatesLarsen
  25

• Flashing Inconsistencies

  #74 opened 3 years ago by GeorgesOatesLarsen
  3

• DUT4 Testing Logs

  #71 opened 3 years ago by GeorgesOatesLarsen
  11

• C.DS1 strangely resistant to soldering

  #77 opened 3 years ago by GeorgesOatesLarsen
  1

• ESPNOW/FreeRTOS/ESP-IDF communications

  #81 opened 3 years ago by GeorgesOatesLarsen
  4

• Malloc and immediate free of peerdata when adding ESPNOW peer

  #84 opened 3 years ago by GeorgesOatesLarsen
  1

• Preprocessor directives possibly needing migration

  #85 opened 3 years ago by GeorgesOatesLarsen
  0

• Deep Sleep Considerations

  #75 opened 3 years ago by GeorgesOatesLarsen
  6

• MKII Rev C Prototype Testing Issues and Observations

  #58 opened 4 years ago by petermccloud
  1

• LED_Builtin and DotStar clock pins are swapped

  #57 opened 4 years ago by GeorgesOatesLarsen
  1

• Rename USING_X to !USING_X

  #59 opened 4 years ago by GeorgesOatesLarsen
  1

• Adjust stencil ratios for battery interface

  #61 opened 4 years ago by GeorgesOatesLarsen
  1

• Maybe add labels for SMD connector pins?

  #69 opened 4 years ago by GeorgesOatesLarsen
  1

• Add rectilinear snap offs

  #63 opened 4 years ago by GeorgesOatesLarsen
  1

• Reduce solder on LTC4353 by 20%

  #66 opened 4 years ago by GeorgesOatesLarsen
  1

• Several components using tdocu instead of silkscreen

  #68 opened 4 years ago by GeorgesOatesLarsen
  1

• Reduce stencil size for USB interface

  #60 opened 4 years ago by GeorgesOatesLarsen
  1

• Part Names need to be renumbered one last time

  #56 opened 4 years ago by GeorgesOatesLarsen
  4