mck1117/wideband

Issues

• brand new sensor failed to heat

  #299 opened a year ago by rusefillc
  4

• Modifying code for the F0 board

  #300 opened a year ago by ChubbyBunny1
  0

• how fast do we expect things to start?

  #296 opened a year ago by rusefillc
  5

• 042 master hangs up after a couple of seconds

  #297 opened a year ago by rusefillc
  1

• 65 seconds to detect lack of sensor

  #295 opened a year ago by rusefillc
  0

• is anything broken on this log?

  #279 opened a year ago by rusefillc
  2

• switch to use libfirmware timer

  #291 opened a year ago by mck1117
  1

• wideband_image.h generation script/documentation

  #284 opened a year ago by rusefillc
  0

• 042 design as standalone not rusEFI WBO

  #194 opened 2 years ago by rusefillc
  2

• wideband_image.h automation

  #283 opened a year ago by rusefillc
  0

• fault detection and heater state - sounds like stuff is complicated enough to deserve a unit test

  #218 opened a year ago by rusefillc
  2

• [dual rev0] No reading for 30 seconds after engine restart

  #215 opened a year ago by rusefillc
  6

• Bosch sensors

  #246 opened 2 years ago by ChubbyBunny1
  4

• Add hardware for onboard voltage sensing.

  #16 opened 2 years ago by kjngineering
  4

• Alternative approach to self-contained WBO

  #195 opened 2 years ago by rusefillc
  1

• is VND7NV04 a safe option?

  #174 opened 2 years ago by rusefillc
  1

• kicad5 or kicad 6?

  #191 opened 2 years ago by rusefillc
  3

• board_carrier does not have SEL provisions

  #193 opened 2 years ago by rusefillc
  0

• master is broken

  #179 opened 2 years ago by rusefillc
  3

• hard fault on boot with GCC 11

  #170 opened 2 years ago by mck1117
  11

• convert to temperature

  #18 opened 2 years ago by mck1117
  0

• GetConfiguration() returns Configuration (not Configuration* or Configuration&)

  #147 opened 2 years ago by dron0gus
  1

• AUX output

  #168 opened 2 years ago by pink-fr3ud
  3

• Wideband failed to startup after cranking

  #34 opened 2 years ago by BeerMoneyMotorsports
  3

• voltage reference BOM cost

  #61 opened 2 years ago by rusefillc
  0

• dual sensor support

  #51 opened 2 years ago by rusefillc
  0

• op-amp part options

  #46 opened 2 years ago by rusefillc
  1

• STM32F030K6 is pretty available for $4

  #21 opened 2 years ago by rusefillc
  0

• We need a 52mm screen option

  #14 opened 2 years ago by rusefillc
  0

• Carrier, Parts shortage, BOM D1

  #27 opened 2 years ago by rusefillc
  1

• mosfet PN alternatives

  #22 opened 2 years ago by rusefillc
  0

• F103 port of firmware

  #28 opened 2 years ago by rusefillc
  1

• is LSU_Vm used? is LSU_Vm protected?

  #29 opened 2 years ago by rusefillc
  2

• Analog output

  #12 opened 2 years ago by rusefillc
  3

• Access to I2C bootloader

  #24 opened 2 years ago by rusefillc
  0

• Bluetooth

  #60 opened 2 years ago by rusefillc
  1

• 780C is very imporant

  #69 opened 2 years ago by rusefillc
  3

• master does not link for F103 firmware

  #128 opened 2 years ago by rusefillc
  3

• virtual zero range should be 5v not 3.4v

  #67 opened 3 years ago by rusefillc
  4

• DAC and PID nerst control is not the best control strategy

  #68 opened 3 years ago by rusefillc
  2

• Add switchable RC circuits to support LSU-4.9 and LSU-ADV?

  #17 opened 3 years ago by kjngineering
  10

• F103 CAN baud rate

  #44 opened 3 years ago by rusefillc
  10

• BOM/CPL for fw_tool

  #45 opened 3 years ago by de1phi48
  0

• F103 no longer blinks

  #43 opened 3 years ago by rusefillc
  3

• through-hole option for MOSFET

  #23 opened 3 years ago by rusefillc
  1

• Control heater from ECU

  #13 opened 3 years ago by mck1117
  4

• what happens to ESR when engine is started without the heater running?

  #19 opened 3 years ago by mck1117
  0

• Make CAN protocol option to emulate MoTeC LTC/D.

  #15 opened 3 years ago by kjngineering
  0

• hardware support for hard-coded index

  #11 opened 4 years ago by mck1117
  3

• clamp esr over CAN to prevent overflow

  #8 opened 4 years ago by mck1117
  1