Pinned issues
Issues
- 4
- 1
Heat tuning pid/bang bang issue
#1310 opened by Devil3dEG - 1
- 0
Auto mesh isn't working
#1300 opened by whop3r - 5
not able to compile SKR mini3 v3 with BLT UBL AND NP
#1279 opened by blackoutlaw - 7
[BUG] M600 resumes mid air Ender 3V2
#1256 opened by Vic152 - 2
- 2
Firmware Randomly Stops Printing
#1263 opened by Nebtek0 - 17
Out of bounds error when trying to do tramming wizard at first boot after Anniversary 2023 firmware update.
#1186 opened by megames07 - 3
- 5
[Issue] Low bed heater PWM frequency powersupply noise
#1293 opened by keever50 - 4
AML 2.0 sets limits to tramming locations
#1179 opened by smeyernyc - 9
[BUG] Tramming Wizard won't go to all 4 corners and Autobuild Mesh is not moving correctly
#1294 opened by TimothyGaray - 3
[BUG] unable to print because my printer cant do homing, my z axis won't go down, only up
#1178 opened - 5
- 3
- 4
[BUG] JPG thumbnail not shown.
#1176 opened by Crazy-Charles - 11
[BUG] Numbers in auto leveling not shown unless bed tramming wizard is run first (TJC)
#1291 opened by floorcat - 4
[BUG] (support for runout sensor not working)
#1243 opened by CalDymos - 1
X and Y Endstops are inverted in SKR Mini E3 V3
#1252 opened by Cahmarfil - 4
[BUG] Cleaning/prime the nozzle off the table
#1257 opened by ms-daniel - 3
[BUG] (f4 chip in ender 3 s1 is not flashing onto ender 3 s1 when put into printer)
#1258 opened by superior-julz - 3
No led control menu newest firmware
#1254 opened by heidepiek - 4
[BUG] (New Firmware keeps saying Z is triggered)
#1166 opened by OldNRelentless - 44
- 2
Hot motors latest firmware
#1183 opened by lawhitecross - 4
- 6
- 2
MINTEMP Error / Nozzle is too Cold
#1237 opened by Nebtek0 - 2
- 10
[BUG] Printer occasionally restarts after selecting gcode with thumbnail
#1249 opened by Spencer-Yoder - 5
My ender 3 s1 extruder motor is not working
#1247 opened by Caverius - 2
[BUG] UBL not compensating while print first layer.
#1250 opened by hendrixradek - 3
- 3
[BUG] Try to Auto Mesh Bed level with G29
#1282 opened by Gurke258 - 3
[BUG] Creality Ender 3 V2 Neo, remaining time is invalid until near the end of the print
#1223 opened by Flybeaux - 5
[BUG] UBL Mesh grid size resets to 5x5 after restart
#1224 opened by Abasz - 1
- 7
The mesh inset does not allow the entire bed to be used
#1201 opened by bauch1234 - 2
[BUG] When SPEAKER was enabled, setting `LCD_FEEDBACK_FREQUENCY_DURATION_MS` and `LCD_FEEDBACK_FREQUENCY_HZ` to zero does not turn off LCD encoder tick sound
#1213 opened by Abasz - 4
- 3
[BUG] Disable one of more toolbar options causes screen corruption and reboot if scrolled on the main menu
#1175 opened by Crazy-Charles - 7
- 3
[BUG] display showing weird artifacts
#1246 opened by tonysprenk - 8
- 3
No response to G29 command
#1187 opened by beans-are-gross - 2
[BUG] Flashing on an Ender 7
#1171 opened by AerosolSP - 1
IMPRESSORA NÃO INICIA IMPRESSÃO NO CENTRO DA MESA!
#1244 opened by mrcharlestom - 2
[Documentation] Force ABL before each print.
#1193 opened by wmantly - 1
[BUG] Nozzle Temp drops too low switching layers
#1181 opened by ThoHilde