nanovna-v2/NanoVNA2-firmware

Issues

• No signal generated above 140MHz

  #82 opened 2 years ago by supergps1
  3

• NanoVNA v2 does not start, just blinks

  #18 opened 4 years ago by eried
  19

• How to calibrate the NanoVNA through Python?

  #78 opened 3 years ago by 0xCoto
  3

• Referance clock at 25MHz

  #81 opened 2 years ago by Jampag
  0

• Unable to compile (libopencm3 error)

  #73 opened 4 years ago by nieldk
  3

• using NanoVNA V2 as PC controlled CW generator/sweeper

  #54 opened 4 years ago by ok1vaw
  1

• compiled binary.bin cannot work

  #35 opened 4 years ago by antboy1979
  10

• V2_2(clone) won't boot up screen stays white

  #80 opened 3 years ago by wojciechna
  0

• Are there 6 GHz plans?

  #79 opened 3 years ago by KimIV
  0

• NanoVNA V2 Plus4 display flickers

  #64 opened 4 years ago by phlipse
  11

• Can I change baud rate?

  #77 opened 3 years ago by daehwa
  2

• Group Delay Calculation Does Not Unwrap Phase

  #76 opened 4 years ago by roseengineering
  0

• FFT_SIZE too small for TD lowpass mode

  #74 opened 4 years ago by gfuer
  0

• Sometime Nanovna freezes while moving the marker with the pen

  #70 opened 4 years ago by simonepernice
  0

• Firmware compatibility with chinese devices

  #68 opened 4 years ago by Harvie
  5

• NanoVNA as spectrum analyzer

  #69 opened 4 years ago by Harvie
  0

• update suggestion

  #66 opened 4 years ago by dustinoff
  0

• git reset --hard ... does't work as describes in Readme.md

  #65 opened 4 years ago by dl9sec
  0

• Cross compiling on a Raspberry Pi...

  #63 opened 4 years ago by dl9sec
  0

• Compensate IFFT window / zero-padding loss in TD

  #61 opened 4 years ago by cho45
  1

• Moving a marker back and forth crashes VNA

  #57 opened 4 years ago by Mike4U
  4

• Recommended documentation for nanovna v2?

  #39 opened 4 years ago by eried
  2

• Same Firmware Versions for newer Revisions

  #51 opened 4 years ago by zarath
  1

• Calibration slots with name?

  #53 opened 4 years ago by eried
  10

• Dmesg Always prompt "LIBOPENCM3 DID NOT ENABLE FPU!"

  #38 opened 4 years ago by lzqgdt
  2

• Make distortion and mixer measurements possible by adding offset measurements

  #31 opened 4 years ago by joseph-wu1
  2

• Calibration status not clear when redoing

  #15 opened 4 years ago by Mike4U
  6

• show calibration data when select recall

  #55 opened 4 years ago by DG9BFC
  1

• Touch screen calibration data reset after power cycle on 20201013

  #56 opened 4 years ago by DJRaov
  2

• Touchscreen calibration wrong when display is flipped.

  #34 opened 4 years ago by ph2lb
  2

• add more memories

  #49 opened 4 years ago by DG9BFC
  4

• 20200926 release with SAAS V2

  #50 opened 4 years ago by jmseight
  4

• First S21 measurement out of tolerance

  #33 opened 4 years ago by zarath
  2

• CW-Signal generation is not continous

  #3 opened 4 years ago by zarath
  16

• req: Battery indicator is missing.

  #25 opened 4 years ago by njozsef
  3

• Change Output Power for Amplifier Testing

  #29 opened 4 years ago by drjyeh
  5

• incorrect git commit in compiled version 20200916

  #47 opened 4 years ago by douardda
  2

• Tag and publish a new version of the firmware

  #41 opened 4 years ago by douardda
  4

• Error in variable assignment

  #32 opened 4 years ago by nieldk
  2

• Hang up with 201 sweep point with Transform on

  #37 opened 4 years ago by lzqgdt
  0

• Led lights

  #42 opened 4 years ago by eried
  5

• bootloader compilation is broken by commit e4fecad7

  #26 opened 4 years ago by douardda
  1

• Marker seems incorrect, FW unstable

  #40 opened 4 years ago by mare001
  1

• USB Mode - provide mecanism to stop rf output

  #28 opened 4 years ago by satfan52
  0

• Unable to enter DFU mode

  #7 opened 5 years ago by nieldk
  6

• Bricked

  #6 opened 5 years ago by nieldk
  1

• Locks up with 201 point Transform

  #2 opened 5 years ago by John-Gord
  1

• How to compile?

  #1 opened 5 years ago by sp3rat
  2