napalm-automation-community/napalm-s350

Issues

• cli commands returns NotImplementedError

  #102 opened 6 months ago by gullanetworkcode
  0

• 0.4.1.1 is not published yet

  #91 opened 9 months ago by SanderDelden
  1

• Command timeout should by configured by an option

  #83 opened 2 years ago by qaxi
  0

• ERROR: setup.py is not a valid editable requirement. It should either be a path to a local project or a VCS URL (beginning with svn+, git+, hg+, or bzr+).

  #5 opened 5 years ago by bvbek
  4

• get_config not working under napalm==4.0.0 but works under 3.4.1

  #81 opened 2 years ago by davama
  3

• Support for SG550 Stack

  #29 opened 4 years ago by qaxi
  2

• Add IPv6 addreses to get_interfaces_ip()

  #79 opened 4 years ago by qaxi
  0

• Support for CBS350-48T-4G and|or CBS250-48T-4G

  #75 opened 4 years ago by pantaras
  2

• Remove 's350_base_interfaces' as base napalm added s350 aliases

  #77 opened 4 years ago by qaxi
  0

• lldp neighbors returns short interface names instead of full names

  #74 opened 4 years ago by nniehoff
  2

• force_no_enable

  #73 opened 4 years ago by qaxi
  2

• What getters are you missing the most?

  #46 opened 4 years ago by qaxi
  0

• add addtional network getters get_environment() get_route_to() get_firewall_policies() get_ipv6_neighbors_table()

  #72 opened 4 years ago by qaxi
  0

• add additional functions get_users() ping() get_snmp_information() get_ntp_stats()

  #71 opened 4 years ago by qaxi
  0

• add network information get_vlan() get_mac_addres_table() get_interfaces_counters()

  #70 opened 4 years ago by qaxi
  0

• add advanced config management commit_config() compare_config() compliance_report()

  #69 opened 4 years ago by qaxi
  0

• Add config management functions load_merge_candidate() and load_replace_candidate()

  #68 opened 4 years ago by qaxi
  0

• get_config does not work - "% Unrecognized command"

  #64 opened 4 years ago by smalldatach
  3

• get_cdp_neighbors would be nice

  #65 opened 4 years ago by smalldatach
  1

• add get_environment()

  #63 opened 4 years ago by qaxi
  0

• a bit of doc in README.md

  #34 opened 4 years ago by qaxi
  0

• Incorrect Parsing of show interfaces status on SG300

  #59 opened 4 years ago by nniehoff
  2

• incorrect parsing of hostname and fqdn

  #57 opened 4 years ago by qaxi
  2

• Bad authentication type - netbox

  #52 opened 4 years ago by smalldatach
  2

• missing get_mac_addres_table

  #33 opened 4 years ago by qaxi
  2

• missing get_vlan

  #32 opened 4 years ago by qaxi
  2

• Unit tests for SG550

  #49 opened 4 years ago by qaxi
  0

• Suport for SG550

  #50 opened 4 years ago by qaxi
  0

• parsing show lldp neighbors

  #23 opened 4 years ago by Phill93
  4

• SG500 support

  #37 opened 4 years ago by Phill93
  0

• Unit tests for SG300

  #26 opened 4 years ago by qaxi
  1

• SG300-10 support

  #20 opened 4 years ago by Phill93
  14

• Unit tests for SG500

  #38 opened 4 years ago by Phill93
  1

• get_interfaces_ip invalid output

  #40 opened 4 years ago by Phill93
  3

• wrong model parsing

  #41 opened 4 years ago by qaxi
  0

• Make dependency versions on par with napalm

  #31 opened 4 years ago by qaxi
  1

• Unit tests for SG500 Stack

  #27 opened 4 years ago by qaxi
  0

• Support for SG500 stack

  #28 opened 4 years ago by qaxi
  0

• Unit tests for SG550 Stack

  #30 opened 4 years ago by qaxi
  0

• @qaxi how can i contact you

  #25 opened 4 years ago by Phill93
  1

• move to tox in travis ci config

  #4 opened 4 years ago by cspeidel
  1

• _get_facts unknown

  #24 opened 4 years ago by Phill93
  1

• Issue with py23_compat

  #18 opened 4 years ago by Sislik
  1

• setup.py fails with pip>=10

  #6 opened 4 years ago by cspeidel
  4

• python 2.7 is EOL

  #7 opened 4 years ago by cspeidel
  2

• S300 does not support piping after 'show hosts'

  #1 opened 5 years ago by cspeidel
  1

• Integration with Napalm-Ansible

  #2 opened 6 years ago by barte91
  17