/SWMP-9

A frame for the S&W M&P 9, 9L, and 9C parts kits. (Untested with M&P 40, or M&P 45.)

SWMP-9

A frame for the S&W M&P 9, 9L, and 9C parts kits.

by nguyenkvvn

Description

This is a 3D printable frame for the M&P series pistol. It is compatible with the 1.0/2.0 M&P 9, 9L, and 9C. It is untested with 1.0/2.0 .40's, or 1.0/2.0 .357's. This frame is NOT compatible with the M&P 9 Shield, as that is a different frame size entirely. This frame is NOT compatible with 1.0/2.0 45's, as they utlize a different locking block. Variants provided include texturing and rails. Note that aftermarket triggers and Performance Center triggers may require modification to the striker plate interface loop towards the rear. Girsan M28 SA kits using M&P magazines will require the M&P magazine's retention cutout to be extended width wise, and a reduction to the steel lip of body near the follower's last-round-hold-open geometry. (Using M&P magazines on Girsan M28 SA kits are not recommended.)

Variants

  • SWMP-9 - Standard length grip, with standard length slide. (Matches factory 1.0 M&P 9 offering, and Girsan M28 SA.)
  • SWMP-9 M2.0 - Standard length grip, with standard length slide. (Matches factory 2.0 M&P 9 offering.)
  • SWMP-9C - Compact length grip, with compact length slide. (Matches factory 1.0 M&P 9C offering.)
  • SWMP-9X - Standard length grip, with compact length slide. (Think Glock 19X.)
  • SWMP-9S - Compact length grip, with standard length slide. (Think a Glock 17/L slide on a Glock 26 frame.)
  • SWMP-9S M2.0 - Compact length grip, with standard length slide. (Matches factory 2.0 M&P 9 offering.)
  • MMMMandP - Standard length grip, with standard legnth slide. Has a gas pedal, enhanced ergonomics, and some aesthetic changes. If you have a M&P 9L kit, you can use any frame with the standard length slide. (Not compatible with the Girsan M28 SA)
  • M28SA - Standard length grip. Compatible only with the Girsan M28 SA parts kit

Instructions

  • Print with 100% infill, and four walls.
  • Tree supports are recommended.
  • Print upside down for best appearance only if your support settings are dialed in.

PDF assembly guide included in this release.

Change Log

  • v1.13: Update 1 Release Candidate 13

    • Addressed gap in compact models after magazine is seated.

  • v1.12: Update 1 Release Candidate 12

    • Ensured M2.0 models actually M2.0 geometry
    • Removed obsoleted video guide link

  • v1.11: Update 1 Release Candidate 11

    • Ensured M2.0 models are actually M2.0 length
    • Girsan MC28SA model addressed rear sear block fitment

  • v1.10: Update 1 Release Candidate 10

    • Even more geometry refinements
    • Spun off Girsan MC28 SA into its own variant
    • Compatibility fixes for the Girsan MC28 SA, targeting trigger clearance, rear sear block tolerances, slide release fitment, and slide release ambi delete

  • v1.9: Update 1 Release Candidate 9

    • Refined geometry to accomodate the M2.0 kits yet again
    • Introduced compatibilty for Girsan MC28 SA kits

  • v1.8: Update 1 Release Candidate 8

    • Refined geometry to accomodate the M2.0 kits
    • Added variant for M2.0 full-size slides

  • v1.7: Update 1 Release Candidate 7

    • Added geometry to accomodate the M2.0 kits

  • v1.6: Update 1 Release Candidate 6

    • Updated the trigger pin hole offset to be a little larger so it can go under the takedown lever
    • Fixed the MMMM&P variant's too-thin backstrap

  • v1.5: Update 1 Release Candidate 5

    • Reintroduced MMMM&P variant revised for updated baseline

  • v1.4: Update 1 Release Candidate 4

    • Corrected full-size magwell height to raise 1.5mm

  • v1.3: Update 1 Release Candidate 3

    • QoL update to fix magazine release geometry
    • Corrected full-size magwell height to raise 3.0mm

  • v1.2: Update 1 Release Candidate 2

    • You can now insert the magazine release on either side
    • Revised trigger guard to accomodate after market triggers, and prevent sagging of OEM trigger
    • Reduced magazine catch spring size for better retention
    • Removed MMMM&P variant for future revision and release

  • v1.1: Update 1 Release Candidate 1

    • Updated geometry for the magazine release button

  • v1.0: Final release

    • Promoted RC1 to release.
    • Added assembly video link.

  • v1.0: Release Candidate 1

    • Promoted to RC1.

  • v0.6: Private Beta Candidate 6

    • You no longer have to remove the safety spring and plunger from the rear fire-control module if you have the safety variant.

  • v0.5: Private Beta Candidate 5

    • Reintroduced picatinny variants
    • Further refinements to accomodate fire control groups that had safeties (PROVIDED THE SAFETY LEVER IS NOT USED).
    • Reintroduced MMMMandP

  • v0.4: Private Beta Candidate 4

    • Reconciled changed propagating from altering front locking block distance
    • Allows for rear fire-control modules with safeties to be used (PROVIDED THE SAFETY LEVER IS NOT USED).

  • v0.3: Private Beta Candidate 3

    • Corrected front locking block distance
    • Temporarily removed picatinny and MMMMandP variant

  • v0.2: Private Beta Candidate 2

    • Adjusted full-size magwell fitment
    • Corrected rear rail tolerances
    • Added MMMMandP variant
    • Added trigger safety geometry
    • Adjusted trigger clearance hole

  • v0.1: Private Beta Candidate 1

    • Initial commit

License

No license has been selected as of 2/27/2022.