olkal/HX711_ADC

Issues

• Missing Timing

  #81 opened 3 years ago
  16

• Testing example produces negative weight values

  #80 opened 3 years ago
  1

• Uploading sketch hangs

  #79 opened 3 years ago
  7

• HX711 with Blynk

  #78 opened 3 years ago
  4

• can it be compatible with hx712 too?

  #77 opened 3 years ago
  5

• Measurement value decreases.

  #76 opened 3 years ago
  1

• Nonlinear behaviour 4 loadcells ESP 32

  #75 opened 3 years ago
  7

• About measurement error by moment

  #74 opened 4 years ago
  2

• how to read the value from two load cells

  #73 opened 4 years ago
  2

• How do I reading 3 decimal places result?

  #72 opened 4 years ago
  2

• Calibration on Arduino nano: Load_cell output val: nan

  #71 opened 4 years ago
  4

• Sampling rate is higher than specification, check MCU>HX711 wiring and pin designations

  #70 opened 4 years ago
  3

• no matching function for call to 'HX711_ADC::start(long unsigned int&, boolean&)'

  #69 opened 4 years ago
  2

• startMultiple with Samples 64

  #68 opened 4 years ago
  2

• Remove tare during start up.

  #67 opened 4 years ago
  7

• How to measure average value with HX711_ADC library!

  #66 opened 4 years ago
  3

• Electrical interference issues when using 4 load cells?

  #65 opened 4 years ago
  3

• Drifting Values

  #64 opened 4 years ago
  5

• Initialization issue?

  #63 opened 4 years ago
  2

• startMultiple does not wait until stabilizingtime is over

  #62 opened 4 years ago
  1

• Scale working until reset

  #61 opened 4 years ago
  4

• Question: Hardware SPI possible/advisable?

  #60 opened 4 years ago
  2

• Persistent calibration

  #59 opened 4 years ago
  11

• How to switch the AB channel

  #58 opened 4 years ago
  5

• Stuck in endless while loop startmultiple() with _tare set to false

  #57 opened 4 years ago
  4

• Reset weight value to zero

  #56 opened 4 years ago
  5

• weird output

  #55 opened 4 years ago
  1

• Some warnings from the compiler

  #54 opened 4 years ago
  2

• Loadcell to be global, but assign Pins later on.

  #53 opened 4 years ago
  4

• Clock wrap not catered for and other issues from a code read through

  #51 opened 4 years ago
  7

• Multiply faster than divide

  #50 opened 4 years ago
  1

• Using the library with Arduino MKR 1010 Wifi

  #49 opened 4 years ago
  2

• Inconsistent return types for start() and conversion24bit()

  #48 opened 4 years ago
  1

• Implement in a new sketch

  #47 opened 4 years ago
  6

• Erroneous data after setSamplesInUse()

  #46 opened 4 years ago
  4

• Can't read data when using external crystal

  #45 opened 4 years ago
  22

• Getting Load_cell output val: nan

  #44 opened 4 years ago
  3

• mutli load cells on single CLK pin

  #43 opened 4 years ago
  1

• Any thoughts on support for tiny85?

  #42 opened 4 years ago
  1

• Flushing data after mcu performs a blocking task

  #41 opened 5 years ago
  4

• Overflow of data when there is a small offset at the beginning

  #40 opened 5 years ago
  13

• Issue with tare timeout in startMultiple()

  #39 opened 5 years ago
  1

• Drift Issue using 50 MT x 4 LoadCell (200 MT)

  #38 opened 4 years ago
  19

• function for re-calibrating within a sketch

  #37 opened 5 years ago
  2

• How to get tare?

  #36 opened 5 years ago
  5

• SCK_DELAY 1 necessary for ESP32

  #35 opened 5 years ago
  2

• Linear drift in readings

  #34 opened 5 years ago
  5

• Scale without tare

  #33 opened 5 years ago
  13

• Function update instead getData?

  #32 opened 5 years ago
  1

• how does using 80Hz change the code?

  #31 opened 5 years ago
  4