pdewacht/zram-generator

Systemd unit generator for zram devices

systemd-zram-setup@.service generator for zram devices

This generator provides a simple and fast mechanism to configure swap on /dev/zram* devices.

The main use case is create swap devices, but devices with a file system can be created too, see below.

Configuration

A default config file may be located in /usr. This generator checks the following locations:

• /run/systemd/zram-generator.conf
• /etc/systemd/zram-generator.conf
• /usr/local/lib/systemd/zram-generator.conf
• /usr/lib/systemd/zram-generator.conf

… and the first file found in that list wins.

In addition, "drop-ins" will be loaded from .conf files in /etc/systemd/zram-generator.conf.d/, /usr/lib/systemd/zram-generator.conf.d/, etc.

The main configuration file is read before any of the drop-ins and has the lowest precedence; entries in the drop-in files override entries in the main configuration file.

See systemd.unit(5) for a detailed description of this logic.

See zram-generator.conf.example for a list of available settings.

Swap devices

Create /etc/systemd/zram-generator.conf:

# /etc/systemd/zram-generator.conf
[zram0]
zram-fraction = 0.5

A zram device will be created for each section. No actual configuration is necessary (the default of zram-fraction=0.5 will be used unless overriden), but the configuration file with at least one section must exist.

Mount points

# /etc/systemd/zram-generator.conf
[zram1]
mount-point = /var/tmp

This will set up a /dev/zram1 with ext2 and generate a mount unit for /var/tmp.

Rust

The second purpose of this program is to serve as an example of a systemd generator in rust.

Installation

It is recommended to use an existing package:

• Fedora: sudo dnf install zram-generator-defaults (or sudo dnf install zram-generator to install without the default configuration)
• Debian: packages provided by nabijaczleweli, see https://debian.nabijaczleweli.xyz/README.
• Arch: sudo pacman -S zram-generator (or https://aur.archlinux.org/packages/zram-generator-git/ for the latest git commit)

To install directly from sources, execute make build && sudo make install:

• zram-generator binary is installed in the systemd system generator directory (usually /usr/lib/systemd/system-generators/)
• zram-generator(8) and zram-generator.conf(5) manpages are installed into /usr/share/man/manN/, this requires ronn.
• units/systemd-zram-setup@.service is copied into the systemd system unit directory (usually /usr/lib/systemd/system/)
• zram-generator.conf.example is copied into /usr/share/doc/zram-generator/ You need though create your own config file at one of the locations listed above.

tl;dr

• Install zram-generator using one of the methods listed above.
• Create a zram-generator.conf config file.
• Run systemctl daemon-reload to create new device units.
• Run systemctl start /dev/zram0 (adjust the name as appropriate to match the config).
• Call zramctl or swapon to confirm that the device has been created and is in use.

Once installed and configured, the generator will be invoked by systemd early at boot, there is no need to do anything else.

Testing

The tests require either the zram module to be loaded, or root to run modprobe zram.

Set the ZRAM_GENERATOR_ROOT environment variable to use that instead of / as root.

The "{generator}" template in units/systemd-zram-setup@.service.d/binary-location.conf can be substituted for a non-standard location of the binary for testing.

Authors

Written by Zbigniew Jędrzejewski-Szmek zbyszek@in.waw.pl, Igor Raits i.gnatenko.brain@gmail.com, наб nabijaczleweli@gmail.com, and others. See https://github.com/systemd/zram-generator/graphs/contributors for the full list.