pellcorp/creality

Issues

• switch backup tar ball to zip

  #432 opened 7 days ago by pellcorp
  1

• unload and load macros should refuse to run if print is active

  #436 opened 7 days ago by pellcorp
  0

• Request: Integrate Anycubic Ace Pro MMU to creality

  #433 opened 8 days ago by ducati1198
  2

• Request: Integrate Anycubic Ace Pro MMU to creality

  #431 opened 8 days ago by ducati1198
  1

• stop camera and guppyscreen for btt eddy temp calibration

  #413 opened 9 days ago by pellcorp
  0

• update guided carto and btt eddy macros to use set kinematic instead of force move

  #414 opened 10 days ago by pellcorp
  0

• Make it possible to configure cancel and end print to park at back of printer, but have PAUSE and M600 park at the front.

  #409 opened 11 days ago by pellcorp
  0

• For config overrides when deleting a section for other than printer.cfg comment it out like for deleting a value

  #316 opened a month ago by pellcorp
  1

• Smarter bed warp stabilisation

  #226 opened 11 days ago by pellcorp
  2

• Investigate save and restart issues with causing mcu to disconnect

  #407 opened 11 days ago by pellcorp
  1

• Disable Bed Warp Stabilisation when Print Chamber Temperature is active in slicer

  #382 opened 15 days ago by firepower9966
  0

• Support upgrading guppyscreen via moonraker

  #300 opened 18 days ago by pellcorp
  1

• Merge recent Klipper commit that adds support for Y-Axis twist compensation

  #243 opened 20 days ago by awp0
  2

• Add a message on console for Filament Runout

  #354 opened 22 days ago by leloupgris09
  2

• Add CHAMBER_TEMP parameter to START_PRINT

  #322 opened 22 days ago by pellcorp
  1

• Investigate btt eddy scan causing horizontal_move_z cannot be less than probe z_offset

  #207 opened 22 days ago by pellcorp
  2

• Change kamp purge line to be lower

  #302 opened 22 days ago by pellcorp
  0

• reduce frame rate in S50webcam

  #361 opened 22 days ago by pellcorp
  0

• [EN] Add firmware compatibility for Ender 3 V3/V3 Plus

  #349 opened 23 days ago by boromyr
  2

• Adding power loss (error/mcu disconnect) recovery

  #348 opened 24 days ago by Kytha0
  0

• Calibrate_Cartographer Macro/Calibrate_Scan Macro

  #324 opened a month ago by DubiousBiscuit
  7

• Clarification FAQ Stepper min max

  #325 opened a month ago by DubiousBiscuit
  1

• Add Knomi support

  #220 opened a month ago by Ledzpg
  1

• In btt eddy calibrate bed mesh need to heat nozzle to warm up eddy

  #280 opened a month ago by pellcorp
  0

• Support config overrides for some elements of guppyscreen.json

  #297 opened a month ago by pellcorp
  0

• rename guided carto macros

  #319 opened a month ago by pellcorp
  0

• Make start config pull chamber temp from slicer

  #309 opened a month ago by clutchkick512
  1

• deletion sections in fan control not being saved by config overrides

  #310 opened a month ago by pellcorp
  0

• remove second g28 from quick start.cfg

  #311 opened a month ago by pellcorp
  0

• Considering reitroducing the logic to automatically restart guppyscreen if it crashes

  #306 opened a month ago by pellcorp
  1

• Bypass nginx for webcam.conf

  #239 opened a month ago by pellcorp
  2

• the Mac address file should survive factory reset

  #272 opened a month ago by pellcorp
  1

• Reset Info

  #303 opened a month ago by boromyr
  1

• "On a K1M, you can use the lidar cable either directly by repinning it or via the pass through lidar port on the toolhead"

  #286 opened a month ago by Roadkyll
  1

• Compatibility Info

  #279 opened a month ago by boromyr
  2

• Add a step to the installation process to verify an emergency factory will work in an emergency

  #275 opened a month ago by pellcorp
  1

• Add aux fan variable to end print

  #277 opened a month ago by verrilltp
  2

• investigate why can't switch webcam.conf to non adaptive mode

  #252 opened a month ago by pellcorp
  1

• improve logic to decide when to grab stock printer.cfg

  #264 opened a month ago by pellcorp
  1

• Create a script to generate a support package for easier diagnostics

  #248 opened 2 months ago by pellcorp
  0

• when installing the configupdater python module in installer hide warnings

  #249 opened a month ago by pellcorp
  0

• investigate is start print respects the speed slider

  #244 opened a month ago by pellcorp
  1

• Replace force move in sensorless.cfg with set kinematic position to avoid issues for multi z users

  #206 opened a month ago by pellcorp
  1

• Instead of relying on _CLIENT_VARIABLES default park configuration, configure depending on model

  #246 opened 2 months ago by pellcorp
  0

• incorrect screws tilt adjust coordinates for k1 max

  #202 opened 2 months ago by dprossner
  1

• Investigate missing B belt on GUPPY_BELTS_SHAPER_CALIBRATION macro output

  #225 opened 2 months ago by pellcorp
  1

• update seems to have broken btt calibration

  #222 opened 2 months ago by dprossner
  7

• mcu error with btt eddy firmware

  #224 opened 2 months ago by dprossner
  2

• Provide macro to do input shaping and generate PNGs to /usr/data/printer_data/config

  #205 opened 2 months ago by pellcorp
  1

• BTT Eddy Temperature Calibration

  #203 opened 2 months ago by roofuskit
  2