This branch of the repository holds a Petalinux (2022.2) project to run the Prophesee RTL design on a Kria KV260 board.
The goal of this project is to provide the minimum environment to run a viewer displaying the output of a Prophesee sensor plugged to a Kria KV260 board.
To build this project, you need Petalinux 2022.2.
Clone the current repository and build the project:
git clone git@github.com:prophesee-ai/petalinux-projects.git -b kv260-2022.2
cd petalinux-projects
Then run Petalinux tools to build the system and generate a microSD card image.
source <path-to-installed-PetaLinux>/settings.sh
petalinux-build
petalinux-package --wic --bootfiles "ramdisk.cpio.gz.u-boot boot.scr Image system.dtb"
Write the image the microSD card (the name of the device representing your SD card may vary):
sudo dd bs=4M if=images/linux/petalinux-sdimage.wic of=/dev/mmcblk0 status=progress && sync
Programming the microSD card may take up to 10mn, depending on the microSD card and your reader.
Plug the microSD card and power-up the Kria board. Make sure you have a micro-USB cable to connect the Kria to your computer and possibly a screen connected to the hdmi output.
The linux serial console is on the second serial-over-USB advertised by the board. Serial baudrate is 115200, 8 bits data, no parity, 1 stop bit, without hardware flow control.
minicom -D /dev/ttyUSB1
On the Kria, login is root and password is root, prepare the FPGA design as follows:
# load and set the pipeline with the default script
load-prophesee-kv260-imx636.sh
Then you can start a viewer either on a screen plugged to the board, or on your computer, streaming the display over ethernet. In both case, Metavision requires some information regarding the board, that is exported as environment variables.
To run the viewer on a HDMI screen plugged to the Kria board, start a X server on the board and run Metavision using it as display.
Xorg&
export V4L2_HEAP=reserved
export V4L2_SENSOR_PATH=/dev/v4l-subdev3
# Force the sensor to be always on, to allow register accesses from Metavision
echo on > /sys/class/video4linux/v4l-subdev3/device/power/control
DISPLAY=:0.0 metavision_viewer
To use your own computer as X server, over SSH, identify the IP address of the Kria over ethernet:
root@xilinx-kv260-starterkit-20222:~# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000
link/sit 0.0.0.0 brd 0.0.0.0
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 00:0a:35:15:82:e2 brd ff:ff:ff:ff:ff:ff
inet 10.14.75.154/16 metric 10 brd 10.14.255.255 scope global dynamic eth0
valid_lft 78278sec preferred_lft 78278sec
inet6 fe80::20a:35ff:fe15:82e2/64 scope link
valid_lft forever preferred_lft forever
here it is 10.14.75.154. Just SSH on the board from your computer and run Metavision:
ssh -X root@10.14.75.154
# Log as root and then run the following commands on the board
export V4L2_HEAP=reserved
export V4L2_SENSOR_PATH=/dev/v4l-subdev3
# Force the sensor to be always on, to allow register accesses from Metavision
echo on > /sys/class/video4linux/v4l-subdev3/device/power/control
metavision_viewer