pyr0ball/pyr0piezo

Issues

• doc-site down & some Q's

  #90 opened 4 months ago by hannpet
  3

• [MOUNT] FlyingBear Reborn 2

  #89 opened 9 months ago by jmacato
  0

• [MOUNT]

  #88 opened 2 years ago by jcortenbach
  1

• [FR]Reprap 2 and 3 Configuration

  #66 opened 5 years ago by Afteraffekt
  4

• [MOUNT] E3D Hemera on Ender3

  #86 opened 3 years ago by calebols
  3

• [MOUNT] Ultimaker 2+

  #85 opened 3 years ago by svpcom
  12

• [MOUNT]

  #84 opened 4 years ago by Tinchus2009
  1

• Board burned out

  #83 opened 4 years ago by garyriet
  21

• BLV MGN Cube (CoreXY type) under bed

  #82 opened 4 years ago by DarkTerritory
  0

• [FR]Klipper-config.md Lost?

  #79 opened 4 years ago by Zero-Grav
  3

• [FR]BIGTREETECH-SKR-V1.3 How to install it？

  #81 opened 4 years ago by Zero-Grav
  1

• [MOUNT]Voron2.4or1.8orZero

  #80 opened 4 years ago by Zero-Grav
  1

• -f upload flag in platformio.ini [BUG]

  #76 opened 5 years ago by stmcculloch
  1

• PP_VERSION not defined

  #73 opened 5 years ago by stmcculloch
  2

• [FR] Add E-Mot header to FFC-X-Mot board

  #75 opened 5 years ago by pyr0ball
  0

• [FR] Add motor stall detection to FFC cable chain

  #74 opened 5 years ago by pyr0ball
  0

• [FR] Need documentation explaining what each config parameter does

  #45 opened 5 years ago by pyr0ball
  1

• [FR] Add documentation explaining SJ1 solder bridge

  #41 opened 5 years ago by pyr0ball
  3

• [FR] Need to add a function or sub-program to calibrate the Atmega internal reference

  #33 opened 5 years ago by pyr0ball
  1

• [FR]5v and 3.3v option using LM317

  #67 opened 5 years ago by Afteraffekt
  1

• Configure MCU for i2c slave device

  #22 opened 5 years ago by pyr0ball
  3

• [MOUNT] Railcore II ZL/ZLT

  #69 opened 5 years ago by notacoat
  6

• Add automated thermal compensation control

  #27 opened 5 years ago by pyr0ball
  1

• [FR] Add website URL to board silkscreen

  #40 opened 5 years ago by pyr0ball
  1

• [FR] Detect if no piezo element is plugged in to the PCB header.

  #48 opened 5 years ago by klcjr89
  3

• [FR] Add support for either active high or active low logic

  #61 opened 5 years ago by pyr0ball
  1

• [MOUNT] ADIMLab Gantry-S

  #62 opened 5 years ago by ETE-Design
  4

• [BUG] For VFOL and VCOMP input, parameters don't take immediately

  #56 opened 5 years ago by pyr0ball
  1

• [BUG] RESET config doesn't save back to EEPROM

  #54 opened 5 years ago by klcjr89
  2

• [BUG] Serial input appears to be ignored if VERBOSE is not defined

  #49 opened 5 years ago by foodbandlt
  6

• [FR] PCB pin compatible with arduino nano

  #46 opened 5 years ago by AlmightyFrog
  7

• [FR] Add Eagle Managed Library to Repo

  #52 opened 5 years ago by pyr0ball
  1

• [FR] Automated environment installer

  #50 opened 5 years ago by pyr0ball
  0

• [BUG] Ready light doesn't turn green upon power up unless piezo is manually tapped.

  #47 opened 5 years ago by klcjr89
  8

• [FR] Add documentation regarding the integrated PT100 daughterboard

  #44 opened 5 years ago by pyr0ball
  0

• [FR] Add Piezo Disk soldering guide to docs site

  #43 opened 5 years ago by pyr0ball
  0

• [FR] Define "UP" or relative position of the board for documentation

  #42 opened 5 years ago by pyr0ball
  0

• [FR] Add board revision to silkscreen

  #39 opened 5 years ago by foodbandlt
  0

• Create proper library filestructure

  #30 opened 5 years ago by pyr0ball
  0

• Add logic to automatically adjust thresholds for 3.3v operation

  #32 opened 5 years ago by pyr0ball
  1

• Eliminate floats for code optimization

  #31 opened 6 years ago by pyr0ball
  0

• Firmware Rev.2.x.x, Analog readings being displayed as 1.00 consistently. Not changing with PWM adjustment

  #20 opened 6 years ago by pyr0ball
  3

• Rev.2.x.x - Switch ADC polling to use internal vRef

  #23 opened 6 years ago by pyr0ball
  1

• Firmware Rev.2.x.x - PWM outputs oscillate randomly without settling on correct voltage

  #26 opened 6 years ago by pyr0ball
  0

• Separate definitions and functions for better code hygiene

  #29 opened 6 years ago by pyr0ball
  1

• Separate trigger duration output and trigger reset delay

  #28 opened 6 years ago by pyr0ball
  0

• Add software hysteresis and reduce analog adjustment adjustment increments

  #24 opened 6 years ago by pyr0ball
  1

• Create an x-axis breakout board to replace x-gantry motor cover

  #18 opened 6 years ago by pyr0ball
  1

• Migrate from AVR to ARM (ATSAMD21E Cortex-M0+)

  #21 opened 6 years ago by pyr0ball
  0

• Rev.2.x.x Firmware Drops Duty Cycle to 0

  #19 opened 6 years ago by pyr0ball
  3