A well organized list of every tool I own.
Perfect saw for chopping up 2x4's and other lumber. Maximum angle is 45°. I bought this saw for $5. Probably the best $5 I have ever spent on a tool. It even cuts aluminum (use the old blade for that!).
Track Saw - Grizzly [T10687]
An amazing tool for cutting plywood down into manageable or finished pieces. It makes very accurate straight cuts though 3/4" plywood. Bunny Bar v1, and v2 were both built with this saw. It takes 160mm x 20mm blades.
- 2 x 54" Tracks
- 2 x Track clamps
Hammer Drill/Driver - Milwaukee 1/2" [2704-20]
A great general purpase battery powered drill. It's suprisingly strong. Be sure you have it in the right mode. If you tighten sockets on the drill mode it will twist your wrist really hard.
- M18 batteris
- Wood bit set
- Metal bit set
- Wood hole cutters - all sizes up to 2-1/8"
- Metal hole cutters - most sizes up to 2-1/8"
- Micro drill bit set
ABCo's also has several dill presses.
High Torque Impact Driver - Milwaukee 1/2" [2763-20]
This baby has more torque than most sports cars. It will drive a 24" stake into the playa without a sweat. Use the large batteries, wear ear plugs, and hang on.
- M18 batteris
- Full socket set
- Common size addapters - 3/8", 1/4", 1x4" hex
Impact Driver - Milwaukee 1/4" Hex Hydraulic [2760-20]
A great tool for driving screws and smaller sockets.
- Socket set
- Various bits - Torx, square, Philips
- Adapters and extensions
Pocket-Hole Jig - Kreg Jig K5 [K5]
Everything you need to make pocket-hole joints.
- Pocket-Hole Plug Cutter - Kreg [C22]
Plunge Router - Dewalt 1.25HP 1/4" [DWP611PK]
- Full set of bits
- Circle cutter - Jasper 2-1/4" to 18-3/16" [200J]
- Edge guide [DW6913]
- 30° chamfer bit - 1/2" shank
- Staight 1/4" straight bit with bearing
- Spiral cut 1/4" bit
- Full set of bits
Mig Welder - [Lincoln Electric 140C]
This is a great little welder. It runs on 110v AC and has a small gas tank so it fits into a car and can be used on site easily. It's good for mild (normal) steel up to 1/8" thick. So far it's built a bed frame, several tables, a four person bicycle, two gates, and steam boiler. It's a hot glue gun for metal and it's fun to use!
- Welding Hood - Autodarkning [Antra AH7-860-0000]
- Welding Hood - Generic brand but still works
Great for cutting mild steel. It's noisy and smelly so used it outside.
Comes in a red bag with the wrench you need to change blades and the optional extra handle. You're also going to want a dusk mask, ear protection, and a face shield. Use this tool with care and think about which way the blade is spinning. This tool likes to kick so hold it firmly and away from your body.
Generator - Champion 3100W/3400W Dual Fuel Inverter [100263]
Has electric start and a buit in voltmeter. Will run an AC unit.
- Extra oil
- Propane adapter
- Jumper cables
- Extra spark plugs
Dremel - [200]
- Random bits
A must have for cleanup. It's smaller size makes portable.
- Pipe wrentch - several sizes
- Needle nose pilers - several sizes
- Wire brushes - steel, brass
- Hand miter saw
- Coping saw - 6-1/2"
- Carpenter saw
- Japan saw - small, medium
- Flush cut pull saw - 10"
- Hacksaw - 12"
- Draw shave
I have had this socket set for over 10 years and never lost a single piece. If you lose a piece plan to stop at the hardware store before returning it!
Many of these tools were purchased to support 8-bit Bunny.