/sterm

🔧 sterm is a minimal serial terminal that focus on being easy to use and not sucking. - This client just works.

Primary LanguagePythonGNU General Public License v3.0GPL-3.0

sterm

Status: 🟢 Active - License: GPL v3

sterm is a minimal serial terminal that focus on being easy to use. - This client just does its job. 

pip install sterm
sterm --help
sterm /dev/ttyUSB0

📝 Table of Contents

🧐 About

sterm is a minimal serial terminal that focus on being easy to use and not sucking. - This client simply works. It has inline input and supports Unicode (utf-8). Each character typed gets directly send to the connected device without buffering. It writes whatever it receives to stdout so that also Unicode and ANSI escape sequences work as expected.

Core Use-Cases

Ideal for debugging:
With the --binary option, the received data will be output byte wise as hexadecimal numbers.

Ideal for a remote Linux shell:
With the --noecho option, each character typed gets directly send to the connected device without buffering and echoing. This makes the Linux console usage seamlessly like using telnet or ssh.

Core Features

  • Inline input
  • No line buffering
  • Unicode support
  • ANSI Escape Sequences supported
  • No GUI

🏁 Getting Started

There are two ways to install sterm. A: Directly using pip or B: from the cloned repository.

Precondition

sterm requires Python 3.8+ to run. Before you start installing sterm make sure you use the correct version. Depending on your distribution, the you may need to use pip3 instead of pip. You can check your Python version by executing the following commands:

python --version
pip --version

Both should print a version number beginning with 3. If not, you need to use pip3 to explicit use Python 3.

For a user-only installation, call pip ... as user. For a system-wide installation you need to be root, or call sudo pip ....

A: Installation using pip

pip install sterm

B: Installation from Repository

# Download
git clone https://github.com/rstemmer/sterm.git
cd sterm

# Dependencies
pip install pyserial

# Install Package
pip install .

Check installation

After installation you can check if sterm is successfully installed using whereis.

whereis sterm
#Outpu: sterm: /usr/bin/sterm /usr/man/man1/sterm.1

There should be two files listed.

  • sterm is the executable, the command you run.
  • sterm.1 is the manual for sterm that can be read by executing man sterm on the command line.

On a system-wide installation, sterm is usually installed to /usr/bin. If you only installed to for a single user, it is usually installed to ~/.local/bin

During the installation process, pip should install all dependencies recursively. To be sure nothing is missing, you can run pip check sterm. It prints all missing dependencies or version conflicts. You can install missing dependencies via pip. When version conflicts are listed, you can hope they do not matter or install an explicit version via pip as well.

🎈 Usage

To execute sterm you just have to call the sterm command in your shell. sterm requires one argument, the device you want to access. All other arguments listed in the subsection below are optional.

UART-Devices are listed in the /dev directory with the prefix tty. Most UART-Devices are addressable via /dev/ttyUSBx or /dev/ttyACMx were x is a number depending on the order they got recognized by the Linux kernel.

sterm has two interfaces:

  1. The command line interface
  2. Escape commands

Command Line Arguments

sterm [-h] [--noecho] [--escape character] [--binary] [-b BAUDRATE] [-f FORMAT] [-w logfile] DEVICE

When a command line argument is contradictory to a setting in the configuration files, the command line argument has higher priority.

  • -h: Print help.
  • -n: Enable noecho mode. Default is echoing each entered key to stdout.
  • --escape: Define an alternative escape character. Default is escape ("\e").
  • --binary: Print hexadecimal values instead of Unicode characters. (Only applied on output, input will still be UTF-8)
  • -b: Baudrate. Default: 115200 baud.
  • -f: Configuration-triple: xyz with x = bytelength in bits {5,6,7,8}; y = parity {N,E,O}; z = stopbits {1,2}. Default: "8N1" - 8 data bits, no parity bits and 1 stop bit.
  • -w: Write received data into a file.

DEVICE is the path to the serial terminal. For example /dev/ttyS0, /dev/ttyUSB0, /dev/ttyUART0, /dev/ttyACM0, /dev/pts/42.

For details read the man-page.

Escape commands

The following strings can be entered while sterm is running. Just hit the escape-key and then enter the commands. They get not send to the device. Instead they are interpreted by sterm. The preceded escape character can be defined with --escape. Default is the escape key ("\e").

  • exit: quit sterm
  • version: print version

Examples

Send ping to UART0 and exit:

sterm /dev/ttyUART0
ping
pong
^[exit

Send hello to a serial device with 9600 baud, 7 data bits, even parity, and 2 stop bits. Then exit:

sterm -b 9600 -f 7E2 /dev/ttyS0
hello
world
^[exit

Connecting to a Linux device

sterm --noecho --escape _ /dev/ttyUSB0
~# whoami
root
~# _exit

Communicating with two sterm instances via a pseudo terminal for testing: A picture that demonstrates the possibility of receiving ANSI escape sequences and unicode charaters

⛏️ Building and Testing

Testing

To test sterm from the sources, just call the test.py script. It runs the command line interface of sterm.

You can use socat to create a virtual serial connection with two endings, so that you can use two sterm processes to communicate with each other:

socat -d -d pty,raw,echo=0 pty,raw,echo=0

Building a new Package

To build a new package from the source code, just execute the pkg-make.sh script. Make sure to update the version number in the sterm/cli.py file. This version number, as well as the README.md file gets read by the setup.py file.

vim sterm/cli.py
./pkg-make.sh

⛓ Related Work

  • tio A more feature rich alternative to sterm with a similar motivation

🎉 Acknowledgements