Issues
- 0
- 0
C67 trace name "CPSV EVAP Purge"
#142 opened by rusefillc - 1
Rename ECU pin 93 to "Heater control"
#146 opened by ElDominio - 9
Figure out wideband present ONLY ON BK2
#143 opened by ElDominio - 6
C67 CPSV needs to be controlled to not have issues with fuel tank depressurization
#141 opened by ElDominio - 1
Изменения пинов MCU
#101 opened by Nadezhda-n - 0
использовать новый power module
#100 opened by rusefillc - 1
- 1
- 2
- 5
rev c: uneven R from CAM to +5v
#111 opened by rusefillc - 0
Rev-D changelist
#134 opened by Qwerty-OFF - 3
WBO module: 2x3 molex and maybe OEM header as well
#137 opened by rusefillc - 1
aux connector silk on both sides
#128 opened by rusefillc - 3
Улучшить схему
#139 opened by Qwerty-OFF - 1
let's use 33810 for injectors and coils
#136 opened by rusefillc - 1
H-bridge SPI
#135 opened by rusefillc - 1
reorder rev C
#138 opened by rusefillc - 7
- 4
four connector holes
#117 opened by rusefillc - 3
re-fab rev C
#110 opened by rusefillc - 0
reorder rev C
#123 opened by rusefillc - 4
F4 top of the line would it be an option?
#130 opened by rusefillc - 2
+12V_PROT
#99 opened by Nadezhda-n - 0
bump mm-mcu version to get extra readability
#127 opened by rusefillc - 13
- 6
- 0
F7 by default
#133 opened by rusefillc - 1
Switch to F7 processor
#129 opened by ElDominio - 1
aux connector pinout silk on back side
#118 opened by rusefillc - 3
Aux LS1, X8 not working
#126 opened by ElDominio - 0
X9 not choosable under Other Sensor Inputs
#124 opened by ElDominio - 1
X10 not choosable for MAP input
#125 opened by ElDominio - 0
Hyundai Genesis "Couple"
#122 opened by ElDominio - 0
23.9-2 board
#121 opened by rusefillc - 3
benc test VSS brake A/C request
#120 opened by rusefillc - 1
rev C PPS2 voltage
#119 opened by rusefillc - 8
Possible user error led to smoke
#115 opened by ElDominio - 2
"OK" board now "3.6-3"
#109 opened by rusefillc - 3
Smiley face "Daniel" board now "3.6-1"
#112 opened by rusefillc - 6
"F7" board now "3.6-2"
#108 opened by rusefillc - 1
Sometimes ETB calibration fails even though it works with a preloaded map; why does this happen?
#114 opened by ElDominio - 2
- 3
rotating components in CPL revC
#105 opened by Nadezhda-n - 1
Put pin K54 as a selectable pin
#104 opened by ElDominio - 7
- 9
Throttle goes to 100% when starting car
#103 opened by Ankyth - 2
J2 should be not C27524
#97 opened by rusefillc - 1
fix capacitor values in the schematics
#96 opened by rusefillc - 1
fix LED schematics
#95 opened by rusefillc