Issues
- 2
GDI4: spark from R71
#266 opened by rusefillc - 0
GDI4: pump output wire colors
#211 opened by rusefillc - 0
PCA9685 is a good and cheap 16 ch PWM generator
#264 opened by dron0gus - 7
revive tle9104
#261 opened by rusefillc - 1
lambda-X2 REV1 A005 LSU4.9 board config
#263 opened by ggurov - 1
lambda-x2: heater wire usability
#262 opened by rusefillc - 5
two issues with Breakout-24pin
#260 opened by rusefillc - 1
VR Hall works with both hall and VR
#214 opened by ElDominio - 4
bad yaml interactive pinout did not fail
#259 opened by rusefillc - 0
test aparatus: toggle all ports in parallel
#258 opened by rusefillc - 1
Gdi4: amperage measurement precision
#256 opened by rusefillc - 22
GDI4 runs out of juice Isense4_high
#221 opened by rusefillc - 0
Gdi4 fw update usability
#257 opened by rusefillc - 3
mcz33810 test board
#255 opened by rusefillc - 2
- 2
VR input soldering test
#254 opened by rusefillc - 1
- 0
dead code or unfinished ideas in test_logic.cpp?
#252 opened by rusefillc - 1
re-order GDI4 rev D
#250 opened by rusefillc - 0
112-17: PPS2 fails stim check
#249 opened by rusefillc - 1
USB problem
#241 opened by andreika-git - 1
GDI4 does not always start
#247 opened by rusefillc - 0
lambda-x2: add pull-down to BOOT1 (PB2)
#246 opened by dron0gus - 0
lambda-x2: add pull down to BT_EN
#245 opened by dron0gus - 6
hellen-honda-k stim profile/pinout
#228 opened by rusefillc - 2
Toggle digital outputs
#222 opened by rusefillc - 1
- 1
2chan IAT/CLT test fails
#240 opened by rusefillc - 4
proteus f7 stim profile/pinout
#234 opened by rusefillc - 0
validate ECU uptime (numSecondsSinceReset)
#236 opened by andreika-git - 1
proteus fails MAP test just a bit
#244 opened by rusefillc - 0
board profile to support multiple revisions
#233 opened by rusefillc - 6
Test ECU outputs using CAN
#237 opened by andreika-git - 0
run testEcuDigitalInputs on separate thread
#243 opened by rusefillc - 0
keyboard entry
#242 opened by rusefillc - 0
154 Hyundai
#238 opened by rusefillc - 3
- 0
GDI4: switch to stm32 part number
#213 opened by rusefillc - 1
stim board to detect weak +12v power supply
#232 opened by rusefillc - 0
2chan stim profile/pinout
#235 opened by rusefillc - 0
no CAN packet is handled as happy CAN state
#231 opened by rusefillc - 3
stim: CAN affects USB
#229 opened by rusefillc - 2
DRV8834 Stepper Motor Driver Carrier
#226 opened by rusefillc - 4
- 1
GDI4 re-fab rev D
#225 opened by rusefillc - 2
GDI4 to use stm32F103CBT6
#224 opened by rusefillc - 4
- 9
- 2
GDI4: another persistence issue
#215 opened by rusefillc - 7
GDI4: configuration persistence is flaky
#212 opened by rusefillc