scottc11/ok-dev-board

Issues

• when exiting FREEZE, update the display based on the sequence progress

  #200 opened a year ago by scottc11
  0

• During record armed stage, listen for any touch events that occur 12 PPQN prior to enabling record and slot those at the position 0 of the sequence

  #199 opened a year ago by scottc11
  0

• Determine sequence length by using a "time signature" parameter, so that a sequence only starts recording on beat 1 of that bar, and ends recording on the last beat of that bar

  #190 opened a year ago by scottc11
  0

• Touch over-ride snapback

  #198 opened a year ago by scottc11
  0

• Pitch bend does not smoothly exit idle position

  #201 opened a year ago by scottc11
  0

• when holding channel select and in quantizer mode, touching a touch pad overrides the quantizing and sustains that note

  #207 opened a year ago by scottc11
  0

• What happens when you have an active sequence running, and then switch into quantizer mode?

  #192 opened a year ago by scottc11
  0

• Bender recording in Pitch Bend mode doesn't playback what you perform (while recording)

  #193 opened a year ago by scottc11
  1

• Add a version key to the start of the settings Flash storage location

  #195 opened a year ago by scottc11
  0

• How do all the alternate functions and menues react when record is enabled?

  #202 opened a year ago by scottc11
  0

• After recording a sequence, if you apply any ratcheting the recorded gate signals stop triggering

  #188 opened a year ago by scottc11
  0

• Allow sequencing the octaves touch pads

  #189 opened a year ago by scottc11
  0

• Gesture to save all active sequences between power cycles

  #185 opened a year ago by scottc11
  0

• ADC reads when at 0v / GND freeze the system

  #187 opened a year ago by scottc11
  1

• If you use a really low frequency LFO, the quantizer will not latch to any new notes

  #182 opened a year ago by scottc11
  0

• Gesture for clearing 1VO Calibration Data (ALT + Cal. 1vo + Clear Conf.)

  #210 opened 2 years ago by scottc11
  0

• Gesture for clearing Bender Calibration (ALT + Bend Mode + Clear Conf.)

  #209 opened a year ago by scottc11
  1

• Store octave position in flash

  #208 opened 2 years ago by scottc11
  0

• Need a way to add silence into a sequence

  #204 opened 2 years ago by scottc11
  0

• Jumper Option: Octave shifts don't trigger the gate

  #205 opened 2 years ago by scottc11
  0

• When loading a saved sequence, device will freeze after the sequence loops once

  #212 opened a year ago by scottc11
  0

• Rework Bender Calibration display gesture

  #163 opened 3 years ago by scottc11
  1

• VCO Tuner does not recieve values on the queue if no signal is plugged into the CV input jack 🤷‍♂️

  #162 opened 3 years ago by scottc11
  1

• Flash / Blink the current step in the display at the same rate of Tempo LED

  #166 opened 3 years ago by scottc11
  0

• Try disabling the seq clock when entering VCOI calibration

  #171 opened 3 years ago by scottc11
  0

• CV Mode button doesn't cycle through the modes

  #203 opened 2 years ago by scottc11
  1

• Active Degree Limit

  #180 opened 2 years ago by scottc11
  0

• Copy Paste a channels sequence length by pressing entering Seq Length menu, holding target channel and destination channel

  #165 opened 3 years ago by scottc11
  0

• make the TH Pads on the power header bigger / wider (drill stays the same, diameter / exposed copper increases)

  #167 opened 2 years ago by scottc11
  1

• AVDD pin needs a ferrite bead between 3v3 supply

  #173 opened 2 years ago by scottc11
  1

• Stopping and launching a sequence (like in ableton)

  #197 opened 2 years ago by scottc11
  0

• Tap Tempo

  #196 opened 2 years ago by scottc11
  0

• Clearing a sequence while record enabled is buggy

  #169 opened 2 years ago by scottc11
  1

• Quantization on record

  #186 opened 2 years ago by scottc11
  0

• Hardware 4-stage toggle switch for setting 3/4, 4/4, 5/4 and 7/4

  #194 opened 2 years ago by scottc11
  0

• Power MCU via USB when not connected to 12V supply

  #174 opened 2 years ago by scottc11
  1

• What are you going to do with the SX1509 clock jumper?

  #168 opened 3 years ago by scottc11
  0

• Layer Stackup guidlines

  #184 opened 2 years ago by scottc11
  0

• Transposition of all 4 channels

  #183 opened 2 years ago by scottc11
  0

• Switch and Jack nuts become loose during shipping, secure with Split Washers?

  #181 opened 2 years ago by scottc11
  0

• Allow CLEAR to work for all currently touched channel select pads

  #179 opened 2 years ago by scottc11
  0

• Disable console logging for production

  #164 opened 2 years ago by scottc11
  0

• Allow RESET and FREEZE for individual channels

  #158 opened 2 years ago by scottc11
  0

• In quantizer mode, make the active degrees and octaves much dimmer then the current degree and octave

  #170 opened 2 years ago by scottc11
  0

• Bender sequence doesn't play back when in quantizer mode

  #177 opened 2 years ago by scottc11
  1

• Bender sequencing (at least pitch bend) does not playback in seq length mode

  #172 opened 2 years ago by scottc11
  0

• If a channel is in quantizer mode, the display LEDs do not illuminate when you press record

  #178 opened 2 years ago by scottc11
  0

• Sequence Octave LEDs don't re-init coming out of Pitch Bend Range UI

  #159 opened 2 years ago by scottc11
  0

• Create a Display gesture when deleting config data

  #157 opened 2 years ago by scottc11
  0

• Pitch Bend does not playback in sequence

  #161 opened 2 years ago by scottc11
  0