sinara-hw/Booster

Issues

• SCPI interface crashes firmware

  #347 opened 4 years ago
  4

• VCP echo

  #346 opened 5 years ago
  6

• LT304x fast start

  #345 opened 5 years ago
  0

• Add TVSs

  #344 opened 5 years ago
  17

• Test check list

  #343 opened 5 years ago
  10

• Testing: symptoms of damage

  #342 opened 5 years ago
  16

• fan exhaust to back

  #341 opened 3 years ago
  5

• scpi interface crashes

  #340 opened 5 years ago
  3

• Testing check list

  #339 opened 5 years ago
  9

• temperature does not update when all channels enabled

  #338 opened 5 years ago
  21

• out bias isolation resistor

  #337 opened 5 years ago
  3

• input attenuator

  #336 opened 5 years ago
  2

• scrap PHA-1

  #335 opened 5 years ago
  28

• With one channel missing, others show errors too

  #334 opened 5 years ago
  5

• Capacitor ratings

  #333 opened 3 years ago
  8

• Channel death (little gain) on v1.4 Booster 003B002F3037470535353239

  #332 opened 5 years ago
  15

• rev1.41 changelog

  #331 opened 5 years ago
  2

• SMA cable length

  #330 opened 5 years ago
  1

• Slow gain changes (> 3 dB!) on Booster 003B002E3037470535353239

  #329 opened 5 years ago
  288

• Transient channel fault on Creotech v1.3 Booster (devid 003200223436510B32323838)

  #328 opened 5 years ago
  9

• SCPI interface freezes

  #327 opened 4 years ago
  5

• consider replacing I2C ADC

  #326 opened 5 years ago
  1

• periods of excessive current noise on some channels

  #325 opened 5 years ago
  52

• booster current readout resolution

  #324 opened 5 years ago
  3

• RF module screw clearance

  #323 opened 5 years ago
  5

• VCP 'powercfg' does not validate arguments

  #322 opened 5 years ago
  6

• Short on 3V3 rail

  #321 opened 5 years ago
  26

• can't run two SCPI connections at once

  #320 opened 5 years ago
  12

• watchdog reset

  #319 opened 5 years ago
  54

• Booster should start with all channels in ERROR mode after watchdog reset

  #318 opened 5 years ago
  2

• ethdbg not documented

  #317 opened 5 years ago
  0

• scpi fails to respond to command

  #316 opened 5 years ago
  21

• v1.4 testing

  #315 opened 5 years ago
  27

• Input detector components not mounted

  #314 opened 5 years ago
  2

• Input detector ADC not working on some channels

  #313 opened 5 years ago
  22

• Lower the U7 gain to 1x

  #312 opened 5 years ago
  2

• hysteresis

  #311 opened 5 years ago
  32

• power sequencing

  #310 opened 5 years ago
  9

• 6V0 current is reported, but that rail doesn't exist

  #309 opened 5 years ago
  0

• Bias current fluctuations

  #308 opened 5 years ago
  30

• VCP should only speak when spoken to

  #307 opened 5 years ago
  1

• I2C errors

  #306 opened 5 years ago
  39

• ERROR on excessive current draw on 6V rail

  #305 opened 5 years ago
  2

• watchdog resets

  #304 opened 5 years ago
  2

• I2C errors

  #303 opened 5 years ago
  9

• long-term stability

  #302 opened 5 years ago
  0

• dead channel

  #301 opened 5 years ago
  48

• I2c errors etc should be visible

  #300 opened 5 years ago
  3

• post python driver

  #299 opened 5 years ago
  2

• vcp hw id

  #298 opened 5 years ago
  1