ATtiny 1616 Development Board is a small and handy development board built around new generation of ATiny series. It is pin and size compatible with Arduino Nano board and can be used as it's direct replacement (with certain limitations). It can be programmed using both Arduino IDE and Platformio IDE, as well as vanilla console tools.
I'm a big fan of early ATtiny series chips, I even made my own ATtiny Flasher tool for productive development and few educational kits based on ubiquitous ATtiny85. Time has come to extend my horizons and look into the modern line of ATtiny chips, specifically so called 1-series and 2-series line of MCUs.
No need to mention that they went far ahead old series, and having resources comparable with old ATmega series. This gave me an idea to make Arduino Nano pin compatible development board, so I can start using it the projects, where I'd normally pick Arduino Nano. In my practice the best way to get familiar with new hardware is to start using it in the actual projects.
- ATTINY1616 8-bit MCU in a 20-pin package
- Up to 20 MHz guaranteed by manufacturer, up to 32 MHz reported by community in normal conditions
- 16 KB Flash
- 2 KB SRAM
- 128B of EEPROM
- UPDI interface for flashing and debugging
- Onboard 5V LDO (disconnected for low power applications)
- Flash using Arduino IDE, Platformio, or the IDE of your choice
- Onboard USB-Serial bridge (CH340E) connected to hardware Serial port
- One RGB LED (WS2812B)
- One Push button
ATiny1616 is a mid-range chip in new ATtiny 1-Series line. Generally they offer considerably more than older Tiny-series chip, and comparable with classic ATmega AVRs, offering at the same time new MCU features, not available in older series.
| ATTINY88 | ATTINY1616 | ATmega168P | ATmega328P | |
|---|---|---|---|---|
| Max Frequency | 20 Mhz | 16Mhz | 16Mhz | |
| Flash | 8KB | 16KB | 16KB | 32KB |
| SRAM | 512B | 2KB | 1KB | 2KB |
| EEPROM | 64B | 128B | 512B | 1024B |
| GPIO count | 28 | 18 | 23 | 23 |
| UART | No | Yes | Yes | Yes |
| I2C | Yes | Yes | Yes | Yes |
| SPI | Yes | Yes | Yes | Yes |
| Timers | 2 | 4 | 3 | 3 |
| PWM channels | 2 | 4 | 6 | 6 |
| ADC pins | 8 | 12 | 8 | 8 |
Note: Revision A and B has backside pin lables rotated, big š¤¦ for me. It will be fixed in the next revisions.
Spence Konde created and maintains Arduino Core. This is a great place to start to get to know new chips better, and understand what is supported and what isn't.
Spence Konde created another great writeup on the flasing routines for the new chips. Short summary below
- (a) Legacy way is to take any Arduino Nano board and use jtag2updi project to make yourself a programmer.
- (b) Better (read recommended) way is to use SerialUPDI tooling with hardware modified serial programmer
- (c) Alternative is to use Optiboot bootloader and Serial programmer interface like on Arduino boards
Method (c) is disqualified on 1-Series chip because of RESET/UPDI pin collision, and both (a) and (b) work equally well. Difference being what is easier for you: (a) dedicate Arduino Nano board for programming or (b) do solder job on your usb-serial adapter.
| Method | Connection |
|---|---|
| jtag2updi |  |
| SerialUPDI (recommended) |
 |
Starting from revision B diode between TX and RX pins are included on the board, so you can use unmodified USB-Serial adapter.
| Method | Connection |
|---|---|
| jtag2updi |  |
| SerialUPDI (recommended) |
 |
Working on one of the projects, it came to me, hey, there is already USB-Serial adapter on the board, serving Serial communication. Why not to use it for flashing. So revision C came, no external programmer needed, plug-n-play. Drawback is that you lose Serial communication via built-in USB.
Use Arduino 1.8.x, Core doesn't work with 2.X versions of Arduino at the moment of writing.
Add http://drazzy.com/package_drazzy.com_index.json to board manager
After that you should install megaTinyCore from Board Manager
Select ATtiny1616 as target and other necessary settings in the board settings after
After installing Plarformio IDE, open sample project. Run Build command to install necessary tools and libraries.
Next run Upload: tiny1616-jtag2updi task if you're using jtag2updi programmer, or Upload: tiny1616-serialupdi task if using modified Serial adapter method. In both cases you can use Upload and Monitor task.
Weekend project I did for my 6-year old son. Based on Electronic Safe with Arduino project, mostly rewritten in order to add support for async execution.
ATTINY1616 MCU
CH340E USB-Serial Adapter connected to Hardware Serial
WS2812B RGB LED
UPDI Programming and Debug header
Hardware Push button
VIN disconnect - cut this line to disconnect LDO chip and power-on LED, recommended for low-power applications
RES disconnect - short this line to enable auto-RESET functionality with Optiboot bootloader (read below)
As explained in many details by Spence, 1-Series chips cannot provide Arduino-like one-click-upload with Optiboot behavior without some sacrifice. Reason for that is pin collision: UPDI and RESET are the same pin, so you need to decide which you'd prefer. If you use auto-reset, you lose UPDI, specifically possibility to change fuses easily (this is important in my opinion). If you use UPDI you need 2 connections to your MCU - one via programming interface, another one for Serial communication.
Personally I prefer to keep UPDI and use direct programming without custom bootloader, having extra wire is minor inconvenience for me, but losing fuses permanently is not an option.
In limited quantities possible to buy at Tindie.