sensor.mopeka_pro_check

THIS INTEGRATION NO LONGER WORKS AS OF SUMMER 2022!!!

Home Assistant now has native support but the native integration doesn't do tank percentage calculation. Follow this discussion for updates or comments. #22

There is a great esphome integration that works well and is easy to use.
Please checkout the esphome integration here https://esphome.io/components/sensor/mopeka_pro_check.html?highlight=mopeka

OLD Stuff below

Home Assistant custom component to support Mopeka Pro Check Tank Level Sensors A custom component for Home Assistant that listens for the advertisement message broadcast by Mopeka Bluetooth propane tank level sensors.

Supported Devices

Mopeka Pro check https://mopeka.com/product/mopeka-check-pro-lp-sensor/

Installation

1. Install the custom component:

The easiest way is to install it with HACS. First install HACS if you don't have it yet. After installation, the custom component can be found in the HACS store under integrations.
Alternatively, you can install it manually. Just copy paste the content of the sensor.mopeka_pro_check/custom_components folder in your config/custom_components directory. As example, you will get the sensor.py file in the following path: /config/custom_components/mopeka_pro_check/sensor.py.

2. Restart Home Assistant:

Restarts just make everything better.

3. Add the platform to your configuration.yaml file (see below)

4. Restart Home Assistant:

A second restart may be required to load the configuration. Within a few minutes, the sensors should be added to your home-assistant automatically (at least two scan_interval may be required. If the scan_interval is set to a time greater than two minutes, at least four scan_interval may be required).
Make sure you have woken up the sensor by following the directions supplied with your sensor. Sensors are shipped from the factory in a low power mode and will need to be woken up to start reporting.
Physically install the sensor following the supplied directions.

Troubleshooting and help

This is still a work in progress with very limited testing. Please use github issues, pull requests, and discussion to provide feedback, open issues, or ask questions. I am new to developing for HomeAssistant so for general questions or system questions using the home assistant forums would be better. Eventually it looks like most add a community post and i will do so once this component works or is in shape for sharing.

Configuration Variables

Specify the sensor platform mopeka_pro_check and a list of devices with unique MAC address.

NOTE: device name is optional. If not provided, devices will be labeled using the MAC address

sensor:
  - platform: mopeka_pro_check
    mopeka_devices:
      # Just use default tank type
      - mac: "A1:B2:C3:D4:E5:F6"
        name: RV Right Tank
      # Set the tank type to a standard 20lbs vertical tank
      - mac: "A6:B5:C4:D3:E2:F1"
        name: RV Left Tank
        tank_type: "standard"
        tank: "20lb_v"
      # Set the max height in MM using custom tank 
      - mac: "A0:B0:C0:D0:E0:F0"
        name: BBQ
        tank_type: "custom"
        max_height: 452.10
        min_height: 23

Additional configuration options

Option	Type	Default Value	Description
`scan_interval`	positive integer	`60`	The scan_interval in seconds during which the sensor readings are collected and transmitted to Home Assistant. The Mopeka device broadcast rate is configurable using the sensor buttons but this scan_interval helps to limit the amount of mostly duplicate data stored in Home Assistant's database since tank level should not change that quickly
`hci_device`	string	`hci0`	HCI device name used for scanning.

Setting up a new sensor

New in Version 0.2.0

For convenience a service is implemented mopeka_pro_check.discovered that when called will pause scanning for 5 seconds, look for any mopeka sensor that has its green "sync" button pressed and report the mac in the mopeka_pro_check.discovered state. To do this from Home Assistant UI do the following:

Go to "Developer Tools"
Go to "Service" tab
Press the green button on your sensor 10 times quickly to get it out of mfg mode
Press the "Call Service" button in Home Assistant and then press and hold the green button on your sensor.
After 5 seconds go to the "States" tab
Bring up the state of entity mopeka_pro_check.discovered
Look at the "State" and you will see a csv of MAC addresses for any sensor that reported the sync button was pressed.
Now you can go to your configuration.yml and add the sensor.
Reboot and the new entity should show up.

Credits

This sensor component was copied from custom-components/sensor.groveetemp_bt_hci at commit 84cd857ec71e5c076fb37f6748d514aed3c0d210

That repo also mentions

This was originally based on/shamelessly copied from custom-components/sensor.mitemp_bt. I want to thank @tsymbaliuk and @Magalex for providing a blueprint for developing my Home Assistant component.

So I want to thank @Thrilleratplay as well as those mentioned above.

Finally, Mopeka Products was extremely helpful. Their support has been great and the short time I have used their sensor I have been happy with its capability. I would recommend their sensor.

Notices

Since some parts of this were copied from custom-components/sensor.mitemp_bt some components will retain that projects copyright.

MIT License

Copyright (c) 2020 Home-Is-Where-You-Hang-Your-Hack

Permission is hereby granted, free of charge, to any person obtaining a copy
of this software and associated documentation files (the "Software"), to deal
in the Software without restriction, including without limitation the rights
to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
copies of the Software, and to permit persons to whom the Software is
furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all
copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.

spbrogan/sensor.mopeka_pro_check