Raspberry Pi driven chaser lights for K8200 printbed enlightment. Using OctoPrint events with runable Python script for event handling and starting LED sequences.
Standalone runner with buttoncontrolled demo mode and developing sequences.
Hardware layouts included
Thingiverse Project: [http://www.thingiverse.com/thing:234608]
i did a Remix of http://www.thingiverse.com/thing:155262 , but i what more lights, use my M3 screws for mounting the ring and -of course- i what to control every LED for itself. So i rebuild the ring for 12 LEDs and desgin a M3x16mm screws capable mount. Thus far everything works fine, but controlling 12x 5500MCD-LED with 14mA per led may burn the Raspberry Pi GPIOs. To turn LEDs on and off for seconds or minutes with 5v(500mA) from a free USB-Port is no problem - I'm so mighty, i can make light! On the other hand -let Raspberry Pi GPIO controll LEDs that external powered- could handle the power problem with the Pi GPIOs.
I start reading ... AH transistors ... multiplier hfe ... what? ... RTFM ... ah gpio->resistor->transistor->"CONTROL" ... after days of reading physics, math, calculating, understanding, failing and keyboard biteing the plan stands with bias resistors for transistor controll and matching LED resistor arrays. I ask a colleague for checking my calculations and he advised Darlinton-Arrays to me.
Darlington Arrays combine all the suff i calculated days ago and its build for TTL inputs from Pi's GPIO, great! Thanks Robert! So all i need is calculate the LED bias resistors and combine everything on a small prefboad. Thanks to fritzing.org i can provide a full circuit diagram for rebuilding it yourself!
The prefboad buffers 14 GPIO pins(3.3v) to 5v include 12x 150Ohm resistors and 2x 300(2x150)Ohm. One GPIO (pin 26 3.3v OUT) used without Darlington Array as one LED controll with bias resistor. Two buttons connected to I2C witch allready has a 1.8kOhm pull-up resistor so i don't need resistors for button controll. So you get 15 ouputs(3 onBoard) and 2 Inputs.
I use the 12(150Ohm) as chaser lights on my remix of http://www.thingiverse.com/thing:155262 , the three on board LEDs for OctoPrint Sever and Printer status (Server Startup, Printer Connected etc) and the 2 Buttons for chaser light controll (play funky light sequences)
Cause the presents of 1.8kOhm Pull-Up resistors i use the SDA/SCL as inputs for Buttons. Addressed: Pin 3,5 - GPIO-BCM(Rev.2 Board) 2,3, WireingPi Pin 8,9 The Pull-Ups turn the inputs to HIGH, in default state your Buttonpress turn the Input to LOW. So: Pressed = 0, Low, False Normal = 1, High, True That annoying behavior looks kind of "unlogic" ... so i connect the Buttons (they have two connections for Pressed = connected or Pressed = cut Connection) other way to get a logic behavoir: Pressed = 1,True Normal = 0,False. While you connect the Buttons after Booting this works perfect! BUT after i try to restart the "RainbowScreen" stays and no SD-Card Reading was recognizable (little green LED on Pi).
That driving me nuts, everything works fine AFTER booting ... some coffes later i decided to trail and error this out! All measurements going fine - no shorts, no unwanted soldering ... have to be a logic problem! It was .. MY Logic problem! After turnaround the Buttons logic i short circuit the Pi itself through connect ping 3,5 to ground over the Buttons. Pi Boots if you press both buttons, nice for unwanted access (noobs blocked, too) but very annoying for development.
Turnd the buttons back to "normal" behavior: Pressed = 0, False, Low Unpressed = 1, True, High and handle this in Code :]
It's my first Python-Project ever so don't be harsh, i'm open minded and happy about codereviews and feedback :) All python code can be found here https://github.com/thomaskneisel/LightRider I'm still a Python noob so its stay a while in "progress" :)
-
get rid off that "fleshburningsunlike" living room lamp
- until i use Sörli - the first 3D-Printer part Ikea ever invented (good job btw) - everytime i watch the printer doing his work i get blinded for 4-5 min
- Now you say: "Stop watching, you dirty peeper!", but i love to watch my little printer working :D
-
learn some "useable" Elektronics
- controll something "really useful" with a self written program
- Microcontroller concept
- Raspberry Pi GPIO as "Microcontroller"
- Watt is Voltage and Current ;)
- "Short Circuit" is not a Hipster-Band, its not even a friend!
- Calculate bias resistor for LEDs
- Transistors or "why Darlington Arrays are awesome!"
- Soldering - don't burn yourself! - still try that
- Build concepts on Breadboard
- Plan own Prefboards on Computer
- Build my own "hardware"
- don't incinerate my Raspberry Pi, printer, house or myself!
-
learn Python
- Syntax
- Project Structure
- OOP
- CommandLine tool
- Raspberry Pi GPIO with Python
- Input handling with running program e.g. ButtonDaemon(BuDae)
- UnitTesting (@TODO)
- "read" and understand code from an other person
-
let OctoPrint take controll of hardware
- On Board Status Lights
- run chaser light sequences by event
- create some GUI Command to permit control
- try "Event Driven Command Line API" (Stateless)
- How To RPC in Python ?
-
Controll via 2 Hardware Buttons
- On/Off - keep lights on, overwrite states from other instances!
- while Sequence playing to break sequence loop (static var ?)
- Program-Button
- plays sequences incremental
- import all from sequence folder
- loops until On/Off Button - to stop sequence looping
- Press for next sequence
- plays sequences incremental
- On/Off - keep lights on, overwrite states from other instances!
-
consolidate openScad skills
- reuse code (screws)
- How to use for loops to place reapeated holes in circular shape
- "Remix by rebuild"
-
Unite OpenSource Prints with OpenSource Code based on a OpenSource Platform controll OpenSource 3D-Printer!
-
drink a lot of coffee :D
-
"Use" English as Project language
- Till we "Start hacking away" in Job
GPIO Help - http://sourceforge.net/p/raspberry-gpio-python/wiki/Home/
Project layout based on: http://www.jeffknupp.com/blog/2013/08/16/open-sourcing-a-python-project-the-right-way/
options --demo starts the demo mode shows all sequences optinal arg sequence repeats
Buttons to toggle sequences