This is a bearing version of the filament spool holder of the Enraged Carrot Feeder Patch (ERCP) buffer.
The original design can be found at ercf .
This modification is based on the version taken on August 2023.
It remove lots of friction compare to the original one (PTFE version).
I'm getting less failure rate with the bearing version.
It support filament spool up to 80 mm wide.
It uses two 608 bearing plus 95 mm of thread rod. That threaded rod could be M8 (metric) or 5/16" (imperial).
I provide the STL for both version.
By the way, the term "vitamin" simply mean non printer part. Apparently the origin comes from reprap reprap .
Documentation generated by the OpenSCAD library NopSCADlib .
Parts list
Roll Assembly
Handle Part1 Assembly
Handle Part2 Assembly
Optional MainBody Assembly
Main Assembly
Top
Roll
Handle Part1
Handle Part2
Optional MainBody
Main
TOTALS
Vitamins
2
.
.
.
.
2
Ball bearing 608-2RS 8mm x 22mm x 7mm
.
1
.
.
.
1
Heatfit insert M3 x 4mm
.
.
1
.
.
1
Screw M3 cap x 10mm
.
.
.
.
1
1
Threaded rod M8 x 88mm
2
1
1
.
1
5
Total vitamins count
3D printed parts
.
.
.
.
1
1
bearingSH_5_16.stl
.
.
1
.
.
1
bearingSH_M8.stl
.
.
.
1
.
1
mainBodyNoShoulder.stl
.
.
.
.
1
1
nut_5_16.stl
.
.
.
.
1
1
nut_M8.stl
1
.
.
.
.
1
roller.stl
.
.
.
.
1
1
spacer1mm.stl
.
.
.
.
1
1
spacer3mm.stl
1
.
1
1
5
8
Total 3D printed parts count
Top
Qty
Description
2
Ball bearing 608-2RS 8mm x 22mm x 7mm
1 x roller.stl
Insert the bearing 608 at both end of the spool cylinder
Top
Qty
Description
1
Heatfit insert M3 x 4mm
Install the insert on the handle.
Top
Qty
Description
1
Screw M3 cap x 10mm
1 x bearingSH_M8.stl
1 x handle_part1_assembly
Remove the support.
Install the handle with a M3x10 screw ("[a]_Handle_x.stl", piece from the original design, not included here).
Top
Optional MainBody Assembly
1 x mainBodyNoShoulder.stl
This is an optional assembly
If you want to be able to remove the spool from the buffer by pulling the handler you have two choices:
If you're are modifying an existing buffer then you have to cut the shoulder.
If you're building a new buffer then you can print "mainBodyNoShoulder.stl". The shoulder has been removed on the stl.
Top
Qty
Description
1
Threaded rod M8 x 88mm
1 x bearingSH_5_16.stl
1 x nut_5_16.stl
1 x nut_M8.stl
1 x spacer1mm.stl
1 x spacer3mm.stl
1 x handle_part2_assembly
1 x optional_mainBody_assembly
1 x roll_assembly
Screw the threaded rod in the bearingSH. Don't overthight.
Insert a 1 mm spacer
Insert the roller
Insert a 3 mm spacer. You might need to use a thinner or a thicker spacer such that the nut end up flush with the roller.
Screw the nut. Don't overthight. Make sure the roller turn freely.
Top