Open-source signal generator built for the ESP32 family of microcontrollers. Currently supports sine- and square waves. Configuration of the signal generator is done using a web-based UI, which is served directly from the device via WiFi.
The ESP32 DevKitC V4 was used for development and testing.
The Arduino software version 1.8.15 with the esp32 board extension version 1.0.6 was used for building and uploading. To upload the static web files to the device, ESP32 Filesystem Uploader was used.
Build and upload using Arduino. Since the static files of the website are being served from a simple on-device filesystem, it is necessary to format the flash storage once prior to first use:
- Uncomment
#define FORMAT_FILESYSTEMin SigGen.ino - Build and upload
- Comment
#define FORMAT_FILESYSTEMin SigGen.ino - Build and upload again
- [Optional] If you changed the front-end code, run parcel
- In Arduino: Tools > ESP32 Sketch Data Upload (this copies the contents of /data to the µC's flash memory)
The software is configured to connect to a WiFi network after booting, for which the configuration is stored in the µC's EEPROM. At first boot, that configuration is uninitialized and thus, connecting to WiFi will fail.
Whenever a WiFi connection could not be established, the device enters the access-point (AP) mode, acting as a WiFi AP with SigGen as its SSID. The AP mode can be forced by uncommenting #define FORCE_AP in SigGen.ino.
In AP mode, the device's IP address is 192.168.4.1. To configure the device for your WiFi, navigate to http://<DEVICE_IP>, select Configuration in the header menu and set the SSID and enter a password. You can optionally assign a static IP address to the device, as well as configure the gateway and subnet mask.
After writing the configuration to EEPROM, you need to restart the device to apply the changes. This can be achieved either via the reset button on the device itself or by navigating to http://<DEVICE_IP>/reboot.
Visit http://<DEVICE_IP> to bring up the signal generator's UI, which is separated into two tabs (one for each waveform).
- Channel [0-7]: Selects the PWM channel.
- Timer [0-3]: Selects the PWM timer (each timer can be configured independently and multiple channels can be attached to each).
- Output GPIO Pin [PIN#]: Selects the GPIO pin used to output the configured signal for the selected channel.
- Resolution [1-20]bit: Sets the resolution of the selected timer (in bits).
- Highspeed [True/False]: Defines whether the selected timer runs in highspeed mode.
- Frequency [0-40M]Hz: Sets the frequency of the selected timer (in Hz). The maximum frequency depends on the selected resolution.
- Duty [0-100]%: Sets the duty cycle (in %).
- Phase [0-360]°: Sets the phase offset (in °).
- Channel [1/2]: Selects the DAC channel. The ESP32 has two DAC channels (1 and 2) connected to GPIO pins 25 and 26, respectively.
- Clock divider [0-7]: Selects the divider for the selected channel from the DAC clock, which runs at 135Hz.
- Invert [Off/All/MSB/All but MSB]: Sets the inversion mode of the selected channel (MSB for non-inverted sine waves).
- Frequency [17-135k]Hz: Sets the frequency of the selected channel (in Hz). The minimum and maximum frequency depend on the selected clock divider (min = 135/(clk_div + 1); max ≈ 135k/(clk_div + 1)). The DAC can still produce a signal above the maximum frequency, but it will become progressively distorted.
- Phase [0-360]°: Sets the phase offset (in °). This cuts off the sine wave's tips.
- Amplitude [⅛/¼/½/1]: Sets the amplitude to a fraction of the maximum (5V).
The front-end is built using Materialize. The number of static files has been reduced to its practical minimum due to limitations of the webserver. As a consequence, all image data is defined inline and only the CSS file is served separately from the HTML.
Visual Studio Code version 1.43.1 with the Arduino extension was used for development.
Documentation pending (monitor HTTP requests from the UI for reference).
- Add more waveforms (triangle, sawtooth, arbitrary)
- Improve WiFi connectivity (deal with disconnects)
- Bluetooth connectability
If you find a bug, have suggestions or are interested in extending this project, drop me a line or issue a pull request.