wernerdaehn/CC3D-CableCam-Controller

Issues

• odriverobotics.com support

  #35 opened 6 years ago by wernerdaehn
  8

• Control board

  #52 opened 3 years ago by Freeejack
  6

• ODrive Fully operational issue

  #58 opened a year ago by Unyck
  1

• Odrive calibration don't be recognize

  #57 opened 2 years ago by Unyck
  0

• Roller Wheel

  #56 opened 2 years ago by Unyck
  2

• odrive robotics contoller and brushless motor or dc controleur and dc motor

  #54 opened 3 years ago by mackios
  1

• rolling down the trolly

  #55 opened 3 years ago by reffff21
  0

• twitches

  #53 opened 3 years ago by reffff21
  2

• PPM SUm problem

  #49 opened 4 years ago by glassgobo
  1

• Autoplay and safety offset

  #48 opened 4 years ago by Willyfan
  0

• PWM frequency

  #47 opened 5 years ago by litrosy
  2

• Different pinout

  #45 opened 5 years ago by JanneHoo
  1

• Support using the oDrive encoder as positional source

  #40 opened 5 years ago by wernerdaehn
  3

• Assignment of FrSky X9D Taranis

  #42 opened 5 years ago by fjavierparra
  0

• GOTO features

  #33 opened 6 years ago by Willyfan
  12

• Increased range of bluetooth module

  #46 opened 5 years ago by litrosy
  4

• Aux Channel 2&3

  #44 opened 5 years ago by litrosy
  2

• Driving between end points does not work

  #43 opened 5 years ago by litrosy
  4

• Bluetooth module HC-06 connection issue - SOLVED

  #41 opened 5 years ago by litrosy
  1

• Debug information for oDrive

  #39 opened 6 years ago by wernerdaehn
  0

• Command $1 does not work

  #38 opened 6 years ago by wernerdaehn
  0

• Deceleration problem

  #30 opened 6 years ago by Willyfan
  151

• eeprom save failed

  #37 opened 6 years ago by lucaspezzei
  3

• CC3D mini revolution no input signal

  #36 opened 6 years ago by lockheedm
  9

• help for configuration fly sky fs-th9x

  #34 opened 6 years ago by mackios
  25

• Buzzer for end points.

  #32 opened 6 years ago by DmitriySurin
  4

• Passthrough and speed limit

  #23 opened 6 years ago by Willyfan
  5

• $P 1 for automatic play don't work

  #24 opened 6 years ago by Willyfan
  4

• Vesc 6

  #29 opened 6 years ago by Willyfan
  1

• Sbus out Remap

  #31 opened 6 years ago by Willyfan
  1

• Bluetooth connection FLIP 32 and HC-06

  #27 opened 6 years ago by DmitriySurin
  10

• How accurate is the position reading?

  #20 opened 6 years ago by wernerdaehn
  4

• Powering the FLIP board via 6v BEC.

  #28 opened 6 years ago by DmitriySurin
  1

• $N 1500 30 700 command does not change the values

  #26 opened 6 years ago by wernerdaehn
  1

• Validate that the defaults are used after first time flashing

  #25 opened 6 years ago by wernerdaehn
  3

• Problem with mode switch

  #21 opened 6 years ago by Willyfan
  4

• little bug in $i input parameters

  #22 opened 6 years ago by Willyfan
  5

• Writing Endpoints into the EEPROM right after are set

  #18 opened 6 years ago by zond-media
  22

• How accurate is the position reading?

  #19 opened 6 years ago by wernerdaehn
  0

• Automatic Mode

  #16 opened 6 years ago by zond-media
  45

• Bluetooth connection

  #11 opened 6 years ago by Willyfan
  23

• Speed and acc.

  #15 opened 6 years ago by Willyfan
  18

• Add a guided setup

  #7 opened 7 years ago by wernerdaehn
  1

• Problem detecting channels

  #9 opened 7 years ago by cofhal
  3

• Firmware

  #17 opened 7 years ago by Tornvig
  1

• broadcast to the Servo2 output

  #14 opened 7 years ago by zond-media
  13

• flashing the firmware on CC3D EVO

  #13 opened 7 years ago by TillMack
  2

• Wrong argument number for ESC_NEUTRAL

  #12 opened 7 years ago by Willyfan
  2

• Just burned a motor controller

  #10 opened 7 years ago by mitarashki
  2

• Console command to print out the VESC status info

  #8 opened 7 years ago by wernerdaehn
  1