Sketch for Arduino Leonardo/Micro based controller circuit for taiko games on PC and Nintendo Switch
If you are using windows 7, you are not able to upload the code for the second time, because of some driver issues. You have to edit the .ini file and add the details of this device in the Arduino driver file to fix this problem. If you have to use Nintendo Switch functions, please do the following steps on a Windows 10 computer.
Install the latest version of Arduino IDE from the official website: https://www.arduino.cc/en/Main/Software
Before starting Arduino IDE, to enable nintendo switch functionality, replace the following files with the ones provided in "setup" folder:
<your arduino installation path>/hardware/arduino/avr/libraries/HID/src/HID.h<your arduino installation path>/hardware/arduino/avr/libraries/HID/src/HID.cpp
Then copy the text in board.txt in "setup" folder and append it to the following file:
<your arduino installation path>/hardware/arduino/avr/boards.txt
If you've successfully done all the modifications above, you should be able to see the board called "Nintendo Switch Controller" next time you start Arduino IDE:
Please select this board before uploading the code as this is essential for your Arduino Leonardo to be recognized by Nintendo Switch.
To enable or disable keyboard or Nintendo Switch controller functionality, remove or add two characters "//" before these two lines in taiko_controller.ino:
- To enable Switch controller only
//#define ENABLE_KEYBOARD
#define ENABLE_NS_JOYSTICK
- To enable keyboard only (PC only, doesn't work on Switch)
#define ENABLE_KEYBOARD
//#define ENABLE_NS_JOYSTICK
- To enable both (not tested)
#define ENABLE_KEYBOARD
#define ENABLE_NS_JOYSTICK
To set up the circuit, you need an Arduino Leonardo, a set of four piezo sensors, and four 1MΩ resistors for some special cases.
Connect the sensors to the 3.3v pin and the analog pins according to the diagram below:
The mapping of the sensors by default should be:
- Left Rim: A0
- Left Surface: A3
- Right Surface: A1
- Right Rim: A2
To customize the mapping, checkout the parameter section.
For most of the times, plugging the sensors directly into Arduino's pins will work. If the controller seems to be generating random inputs, you can fix this by plugging some 1MΩ resistors in parallel:
For best performance, the sensors must be piezo sensors (a.k.a. piezo speakers, contact microphones). No guarantee if other types of sensors will simply work, but if analog signals with voltage ranged 0-5V are fed into analog pins, this setup should be good to go.
For further improvements, you can use some diodes to limit the voltage of the piezo sensors, or use a 2.5v power supply, but this won't matter in most cases, at least on my side.
If you can somehow connect a 4x4 matrix keyboard (no pull-up resistors needed) to Arduino's digital pin 0-15, it will work as a controller along with the drum:
This sketch uses a dynamic threshold of sensor levels to trigger inputs. Whenever the sensor level from one sensor is higher than the threshold, a keyboard or Nintendo Switch controller input is generated, then the sensors will be put into a cooldown period. When an input is triggered or during cooldown period, the threshold will be raised to a ratio of current sensor levels, and after that the threshold will gradually decay by ratio, to hopefully be an envelope of the waves of sensor levels.
As the sensors should have biased input voltages, the sensor levels are the differential value of the analog value from analogRead.
To deal with four analog inputs, we read the sensor levels one at a time and only do the triggering mechanisms for this sensor. To compensate for the time difference, the sensor level for the current one will be a mix of values from previous read and current read. Also, a customized non-blocking version of analogRead is used to guarantee more stabilization time after a channel switch of Arduino's internal ADC chip.
To deal with Nintendo Switch, I used the HID descriptor for Hori's Pokken fightstick to let Switch trust Arduino as a valid controller device (see the credits section). The default buttons from the four sensors are the analog stick buttons (press the sticks down) and the trigger buttons (ZL and ZR).
As VID and PID of the controller have to be the specific value, the setup to boards.txt is essential. Also, Switch seems to be judging the device strictly by the first-come HID descriptor of the device, so Arduino's default HID behavior have to be altered to have our customized HID descriptor to work.
The minimum value for sensor levels to trigger inputs for all sensors.
To determine an optimal value for this level, try enabling debug info. Usually, this value is only used to ignore sensor noises, but you can use this level as a sensitivity level.
The cooldown length of sensors, in microseconds (=1x10^-6s).
While a sensor is in its cooldown period, no input will be triggered ignoring the sensor level. The threshold level would still be updated if the sensor levels go high. During the cooldown period, the corresponding key of the sensor is kept pressed. When it ended, the key is released.
How much the threshold value is raised to, in ratio to the sensor level.
How fast every threshold level decays, in ratio per refresh (about 300ms).
For every refresh, the threshold value is multiplied by k_decay.
The analog input pins of four sensors.
The key mapping of four sensors, if keyboard inputs are enabled.
Sensitivity of every sensor. All sensor levels are scaled by these values respectively before use.
If the line #define DEBUG_OUTPUT is enabled, there will be debug information printed via serial. Take a look at your serial monitor.
The first 4 columns indicate the current vibration level of the four sensors, and the last column indicates the threshold level for a sensor to trigger an input; the symbols in the middle show the current status of the sensors, # for input triggered and * for cooldown state.
A typical output could be:
0 3 13 63 | | 0
51 2 11 58 | * * * # | 53
83 5 9 24 | # * * # | 83
- This sketch makes use of Arduino IDE and its useful library. A modified version of the Arduino library is used to allow us to make a valid Nintendo Switch controller.
- The HID descriptor is from progmem's work of reverse engineering of Pokken Tournament Pro Pad: progmem/Switch-Fightstick
- The HID descriptor is coded using many useful macros and functions from LUFA Library