CC1101-ESP-Arduino

ESP8266 / ESP32 / Arduino driver lib for using the great TI C1101 transceiver

About

The Texas Instruments CC1101 is a very versatile, high quality and cheap transceiver, supporting a wide range of frequencies and modulations. Ready-to-use CC1101 modules are as cheap as 5.00€ and at the same time significantly better than simple 433MHz receiver and transmitter modules.

The confusing part about these CC1101s is, they are actually kind of over powered, providing logic for sync word detection, CRC checks, packet formats and so on. However, it's still possible to use them as simple digital transceivers, giving them a minimum of configuration and letting the MCU (like our ESP8266/ESP32/Arduino) do all the work. Especially useful, if you want to transmit or decode non-standard packet formats. Like the vast majority of us, I suppose ;)

This library aims to help developers using the CC1101 module without having to read the whole 105 pages datasheet first.

Features

High level access to important features, like switching frequencies, switching between IDLE/TX/RX, sending / receiving data etc.
Low level access, so you can simply read/write directly all CC1101 registers without having to deal with SPI specific stuff.
Written by someone, who actually read the datasheet ;)

CC1101 technical info

RX/TX modes

Asynchronous serial mode
Synchronous serial mode
FIFO

Limitations

I develop this library in my free time. Some features are not done yet. For now only asynchronous serial mode is supported.

Progress

Implemented and test low level SPI communication
Switch between RX, TX and IDLE mode
Read and write data
Set frequency at runtime
Set baud rate at runtime
Set TX Power at runtime
Set RX bandwith at runtime
Set Channel and channel spacing (optional) at runtime
Perform reset of module
2-FSK, 4-FSK, GFSK, MSK and ASK modulation support

TODO

SLEEP mode
synchronous serial mode
FIFO mode
Packet handling features

Examples

Look into /examples :)

Simple_Sender.ino
- This example sends the following waveform.
- The original signal is recorded from a remote control, sending a bit pattern with line encoding using OOK modulation.
- One pulse is 375ms therefore we're sending with 2666 baud.
Listen_and_Print.ino
- Async receive a signal on 433,92MHz and print it.

Wiring

Connect SPI_SCK, SPI_MISO, SPI_MOSI to the corresponding SPI Pins on your board. SPI_CS can be any pin usable as INPUT and OUTPUT, but most boards have a default one.

The CC1101 has two multi-purpose pins, GDO0 and GDO2. (Actually three, but GDO1 is SPI_MISO, which is only usable if SPI_CS is HIGH.)

PIN	FEATURES
GDO0	INPUT/OUTPUT
GDO1	OUTPUT (only usable if SPI_CS=HIGH)
GDO2	OUTPUT

You can connect zero additional pins (GDO0 and GDO2 not connected), but then you MUST use the CC1101 RX/TX FIFOs. In other words, you can't use the more flexible serial mode.
You can connect only GDO0, if you are using asynchronous serial mode. The pin will switch automatically from INPUT to OUTPUT when you call setTX() and vice versa.
You can connect GDO0 and GDO2, then you have the choice between asynchronous serial mode (GDO0 = TX, GDO2 = RX) and synchronous serial mode (GDO = TX/RX, GD02 = clock).
You can use GDO1, but this isn't fully supported by the high level methods of this library. However, you may read the datasheet and use the low level SPI methods for configuration instead.
You can also use the GDOx pins for something else. Again, that's what the low level SPI methods are for.

API

Constructors:

CC1101(int gdo0);
CC1101(int gdo0, int gdo2);
CC1101(int sck, int miso, int mosi, int cs, int gdo0);
CC1101(int sck, int miso, int mosi, int cs, int gdo0, int gdo2);

High level methods:

void init();
void softReset();
void hardReset ();
void setIdle();
void setRx();
void setTx();
void setMHZ(double mhz);
void setChannel(uint8_t channel);
void setChannelSpacing(int spacing_hz);
void setTXPwr(TX_DBM value);
void setRxBW(RX_BW_KHZ RxBW);
void setDataRate(unsigned long baud);
void setModulation(MOD_FORMAT mod);
void setDeviationHZ(int deviation_hz); //1586hz - 380859hz
uint8_t getPartnum();
uint8_t getVersion();

Low level methods:

void spiStrobe(uint8_t strobe);
uint8_t spiReadReg(uint8_t addr);
uint8_t spiReadStatus(uint8_t addr);
void spiReadRegBurst(uint8_t addr, uint8_t* buffer, uint8_t buffer_len);
void spiWriteReg(uint8_t addr, uint8_t value);
void spiWriteRegBurst(uint8_t addr, const uint8_t* buffer, uint8_t buffer_len);

Definitions (see CC1101_ESP_Arduino.h for more)

enum TX_DBM {
	TX_DEFAULT_DBM = 0,
	TX_MINUS_30_DBM = 1,
	TX_MINUS_20_DBM = 2,
	TX_MINUS_15_DBM = 3,
	TX_MINUS_10_DBM = 4,
	TX_0_DBM = 5,
	TX_PLUS_5_DBM = 6,
	TX_PLUS_7_DBM = 7,
	TX_PLUS_10_DBM = 8
};

enum RX_BW_KHZ {
	RX_BW_812_KHZ = 0,
	RX_BW_650_KHZ = 1,
	RX_BW_541_KHZ = 2,
	RX_BW_464_KHZ = 3,
	RX_BW_406_KHZ = 4,
	RX_BW_325_KHZ = 5,
	RX_BW_270_KHZ = 6,
	RX_BW_232_KHZ = 7,
	RX_BW_203_KHZ = 8,
	RX_BW_162_KHZ = 9,
	RX_BW_135_KHZ = 10,
	RX_BW_116_KHZ = 11,
	RX_BW_102_KHZ = 12,
	RX_BW_81_KHZ = 13,
	RX_BW_68_KHZ = 14,
	RX_BW_58_KHZ = 15
};

enum MOD_FORMAT {
	FSK2 = 0,
	GFSK = 1,
	ASK_OOK = 3,
	FSK4 = 4,
	MSK = 7
};

Contribute

Help is always welcome :)

wladimir-computin/CC1101-ESP-Arduino