CarND-Path-Planning-Project

Self-Driving Car Engineer Nanodegree Program

Proejct Rubric

Compliation

The code can compile without errors with cmake and make with the given CMakeLists.txt.

Valid Trajectories

The car is able to dirve at least 4.32 miles without incident. As shown in the figure below, the car has been driven 10.77 miles without incident.

The car drives according the speed limit, which is 50 mph. The max acceleration and jerk are not exceeded. And car does not have any collisions.

The car is able to chagne lanes and the car starys in its lane, except for the time between changing lanes, as shown in the figures below.

Reflection

In line 203 to 210 of main.cpp, four variables are defined for changing lanes and setting the speed limit.

lane: the index of the lane, start in lane 1.
ref_vel: the speed limit of the high way.
turn_steps: the number of time steps for changing lane. The vaule of 100 indicates a time of 100 * 0.02 = 2 seconds for an operation of changing lane.
target_lane: store the index of the target lane for the operation of changing lane.

To avoid collision with the car in front of the driving car, two bool variables too_close and too_much_close in line 261 and 262 are defined with different negative accelecation. In line 293 to 314, the logic of brake is defined to avoid the collision to the front car in the same lane.

The code from line 328 to 385 is used to detect the other cars on the lanes beside the lane the car is driving. The average speed of the cars on the other lanes is calculated and the distances of the closest cars in the front and in the back are stored in variables.

The code from line 387 to 395 defines the brake logic and limits the speed of the driving car less than the speed limit.

The code from 411 to 433 defines the logic to change lane. In the lane next to the lane which the car is driving on, If the car in the front is further than 40m, the car in the back is further than 20m, the speed of the driving car is larger than 25 mph, the average speed of the next lane is larger than the driving car or there is no car in the next lane, and the operation of changing lane has finished, the car will change to the next lane in the next 2 seconds.

The code from line 437 to 545 generates the smoothed trajectory of the driving car with splines, which makes the car does not exceed the limitation of acceleration and jerk.

Simulator.

You can download the Term3 Simulator which contains the Path Planning Project from the [releases tab (https://github.com/udacity/self-driving-car-sim/releases/tag/T3_v1.2).

Goals

In this project your goal is to safely navigate around a virtual highway with other traffic that is driving +-10 MPH of the 50 MPH speed limit. You will be provided the car's localization and sensor fusion data, there is also a sparse map list of waypoints around the highway. The car should try to go as close as possible to the 50 MPH speed limit, which means passing slower traffic when possible, note that other cars will try to change lanes too. The car should avoid hitting other cars at all cost as well as driving inside of the marked road lanes at all times, unless going from one lane to another. The car should be able to make one complete loop around the 6946m highway. Since the car is trying to go 50 MPH, it should take a little over 5 minutes to complete 1 loop. Also the car should not experience total acceleration over 10 m/s^2 and jerk that is greater than 10 m/s^3.

The map of the highway is in data/highway_map.txt

Each waypoint in the list contains [x,y,s,dx,dy] values. x and y are the waypoint's map coordinate position, the s value is the distance along the road to get to that waypoint in meters, the dx and dy values define the unit normal vector pointing outward of the highway loop.

The highway's waypoints loop around so the frenet s value, distance along the road, goes from 0 to 6945.554.

Basic Build Instructions

Clone this repo.
Make a build directory: mkdir build && cd build
Compile: cmake .. && make
Run it: ./path_planning.

Here is the data provided from the Simulator to the C++ Program

Main car's localization Data (No Noise)

["x"] The car's x position in map coordinates

["y"] The car's y position in map coordinates

["s"] The car's s position in frenet coordinates

["d"] The car's d position in frenet coordinates

["yaw"] The car's yaw angle in the map

["speed"] The car's speed in MPH

Previous path data given to the Planner

//Note: Return the previous list but with processed points removed, can be a nice tool to show how far along the path has processed since last time.

["previous_path_x"] The previous list of x points previously given to the simulator

["previous_path_y"] The previous list of y points previously given to the simulator

Previous path's end s and d values

["end_path_s"] The previous list's last point's frenet s value

["end_path_d"] The previous list's last point's frenet d value

Sensor Fusion Data, a list of all other car's attributes on the same side of the road. (No Noise)

["sensor_fusion"] A 2d vector of cars and then that car's [car's unique ID, car's x position in map coordinates, car's y position in map coordinates, car's x velocity in m/s, car's y velocity in m/s, car's s position in frenet coordinates, car's d position in frenet coordinates.

Details

The car uses a perfect controller and will visit every (x,y) point it recieves in the list every .02 seconds. The units for the (x,y) points are in meters and the spacing of the points determines the speed of the car. The vector going from a point to the next point in the list dictates the angle of the car. Acceleration both in the tangential and normal directions is measured along with the jerk, the rate of change of total Acceleration. The (x,y) point paths that the planner recieves should not have a total acceleration that goes over 10 m/s^2, also the jerk should not go over 50 m/s^3. (NOTE: As this is BETA, these requirements might change. Also currently jerk is over a .02 second interval, it would probably be better to average total acceleration over 1 second and measure jerk from that.
There will be some latency between the simulator running and the path planner returning a path, with optimized code usually its not very long maybe just 1-3 time steps. During this delay the simulator will continue using points that it was last given, because of this its a good idea to store the last points you have used so you can have a smooth transition. previous_path_x, and previous_path_y can be helpful for this transition since they show the last points given to the simulator controller with the processed points already removed. You would either return a path that extends this previous path or make sure to create a new path that has a smooth transition with this last path.

Tips

A really helpful resource for doing this project and creating smooth trajectories was using http://kluge.in-chemnitz.de/opensource/spline/, the spline function is in a single hearder file is really easy to use.

Dependencies

cmake >= 3.5
- All OSes: click here for installation instructions
make >= 4.1
- Linux: make is installed by default on most Linux distros
- Mac: install Xcode command line tools to get make
- Windows: Click here for installation instructions
gcc/g++ >= 5.4
- Linux: gcc / g++ is installed by default on most Linux distros
- Mac: same deal as make - [install Xcode command line tools]((https://developer.apple.com/xcode/features/)
- Windows: recommend using MinGW
uWebSockets
- Run either install-mac.sh or install-ubuntu.sh.
- If you install from source, checkout to commit e94b6e1, i.e.
```
git clone https://github.com/uWebSockets/uWebSockets 
cd uWebSockets
git checkout e94b6e1
```

Editor Settings

We've purposefully kept editor configuration files out of this repo in order to keep it as simple and environment agnostic as possible. However, we recommend using the following settings:

indent using spaces
set tab width to 2 spaces (keeps the matrices in source code aligned)

Code Style

Please (do your best to) stick to Google's C++ style guide.

Project Instructions and Rubric

Note: regardless of the changes you make, your project must be buildable using cmake and make!

Call for IDE Profiles Pull Requests

Help your fellow students!

We decided to create Makefiles with cmake to keep this project as platform agnostic as possible. Similarly, we omitted IDE profiles in order to ensure that students don't feel pressured to use one IDE or another.

However! I'd love to help people get up and running with their IDEs of choice. If you've created a profile for an IDE that you think other students would appreciate, we'd love to have you add the requisite profile files and instructions to ide_profiles/. For example if you wanted to add a VS Code profile, you'd add:

/ide_profiles/vscode/.vscode
/ide_profiles/vscode/README.md

The README should explain what the profile does, how to take advantage of it, and how to install it.

Frankly, I've never been involved in a project with multiple IDE profiles before. I believe the best way to handle this would be to keep them out of the repo root to avoid clutter. My expectation is that most profiles will include instructions to copy files to a new location to get picked up by the IDE, but that's just a guess.

One last note here: regardless of the IDE used, every submitted project must still be compilable with cmake and make./

How to write a README

A well written README file can enhance your project and portfolio. Develop your abilities to create professional README files by completing this free course.

xujin1982/CarND-Path-Planning-Project