A repository containing specifications of the Sovol SV06 3D printer parts, as well as links to aftermarket replacement parts.
You can assume that all information herein is accurate unless stated otherwise.
If you found this work useful, please consider buying me a .
You can also contribute by making a pull-request, creating an issue, or starting a discussion.
Some of the links found on this page may be affiliate links.
This repository is a work in progress. Watch for updates:
- Hotend
- PCB
- Filament Sensor
- Heatblock
- Fans
- Probe
- Extruder
- Motherboard
- Lead Screws and Rods
- PSU Related
- Useful Prints
Label | Connection | PCB Connection | Other Connection | Other info |
---|---|---|---|---|
P3 | Coldend fan | JST 1.25mm 2-Pin | ||
P2 | Extruder motor | JST 1.25mm 4-Pin | JST PH 2.0 6-Pin | Cable length 12cm |
P4 | Heater cartridge | JST PH 2.0 2-Pin | ||
P8 | Thermistor | JST 1.25mm 2-Pin | ||
P6 | Probe | JST 1.25mm 5-Pin | ||
P5 | Part cooling fan | JST 1.25mm 2-Pin | ||
P7 | Filament sensor | JST 1.25mm 3-Pin |
I tested two random filament runout sensors that I had on hand. Both work just fine. It seems to me that any sensor with VCC
, Ground
, and Signal
pins should work.
In order to get the filament sensor working, just make sure that the VCC
, Ground
, and Signal
line up with the pins on the hotend PCB, port P7
.
In order to 'mount' the sensor while it's not in use, simply glue a small magnet onto the sensor. You can then stick the sensor onto the extruder motor. You might also want to tether the sensor to the extruder cable with a piece of string.
Klipper filament configuration section:
[filament_switch_sensor filament_sensor]
switch_pin: !PA4 # "Pulled-high"
pause_on_runout: True
insert_gcode:
M117 Insert Detected
runout_gcode:
M117 Runout Detected
The complete Klipper code to make this work is part of my OSS Klipper Configuration.
These can be found for very cheap (roughly $1.5) on Aliexpress and quite a bit more on Amazon (though still very affordable). This is the one I bought. Here's another seemingly viable option.
You need to make your own cable. I recommend getting these JST 1.25 cables, and this XH2.54 kit. You will also need a crimping tool such as the Engineer PA-09.
The SV06 uses a Creality CR10 heatblock which supports MK8 threaded nozzles (including some M6 nozzles). The material is likely nickel-plated copper (needs verification).
The heatblock is mounted onto the extruder assembly using 2 x M2.5 10mm SHCS.
Please see some more relevant details here.
Any of these heatblocks will do just fine, however, may require mounting bolts of different sizes.
The SV06 uses a ceramic heater cartridge.
Voltage | Watts | Dimensions | Connection | Cable Length |
---|---|---|---|---|
24V | 40W | 6x20mm | JST PH 2.0 2-Pin | ~40mm |
The heater cartridge is glued into the heatblock, a heatblock that heats to 300C. Although possible, it is inadvisable, and potentially dangerous to attempt removal.
Unfortunately, a direct, non-DIY replacement seems unlikely. It appears that no one sells heater cartridges with JST PH 2.0 2-Pin connectors.
You would have to buy a heater cartridge such as this, and crimp the appropriate connector on.
The SV06 uses a glass-bead thermistor.
Material | Dimensions | Connection | Cable Length |
---|---|---|---|
Glass | 2mm | JST 1.25mm 2-Pin | ~40mm |
As was the case with the heater cartridge, the thermistor is also glued into place, and is very unlikely to survive removal given the delicacy of the cables and composing material.
Coming soon.
Cooper Portion | Overall Length | Outer Dia. | Inner Dia. |
---|---|---|---|
15mm | 22mm | 7mm | 2mm |
I purchased and tested this heatbreak. It works as well as the stock piece.
The part sold in the link could change, so make sure it has the following specs:
I bought this probe: LJ12A3-4-Z-BY. It's dimensionally correct, however, completely untested!
Axis | Qty | Length | Dia. | Lead | Pitch | Starts | Sovol Part # |
---|---|---|---|---|---|---|---|
Z | 2 | 376mm | 8mm | 4mm | 2mm | 2 | JXHSV06-02003-a |
Axis | Qty | Length | Dia. | Sovol Part # |
---|---|---|---|---|
X | 2 | 355mm | 8mm | JXHSV06-03001-a |
Y | 2 | 340mm | 8mm | JXHSV06-01012-a |
Z | 2 | 400mm | 8mm | JXHSV06-02004-a |
Type | Qty | Dia. | Length | Motor Shaft Dia. | Lead Screw Dia. |
---|---|---|---|---|---|
Rigid | 2 | 20mm | 25mm | 5mm | 8mm |
Brand | Model | Wattage | Voltage |
---|---|---|---|
Cheng Liang | P360W24V | 360W | 24V |
Part |
---|
XT60H-M/F |