JVC Remote

Usage

For interactive use inkvoke the script like this:
python3 -i listen.py
then you can call functions as follows:
>>>initCam()
>>>sendCmd("Autoiris", 0)
>>>sendKey("Iris", 127)

Pinout

26pin_studio_10pin_remote_6pin_tally.xls

Es wird nur der Remote Anschluß benötigt.
Der Stecker ist ein gewönlicher 6pin Mini-Din (der PS/2 Stecker) Anschluß.
Zum Beispiel: http://www.reichelt.de/SE-DIO-M06/3/index.html?&ACTION=3&LA=446&ARTICLE=17457&artnr=SE-DIO+M06

Protokoll

Signallevel: 3.3V
Format: 9600baud 1E8 (8 daten, 1 stop-bit, even-parity)

Protocol Flow

Typical Sequence

Normal CCU to CAM flow
Direction (seen from OCP)	TX	RX	TX	RX
length (in Byte)	1	1	3-4	1
Purpose	Startbyte	ACK	Data	ACK

Note: there is also the possibility to do CAM to CCU communication,
which seems to be requested by a special char (0x90)

Startbyte

Startbyte
Bit	0	1	2	3	4	5	6	7
Purpose	Transmission Start	0		Special	data

On normal (non special) transmission: treat data as number of bytes to be transmitted.
If Special bit is set: data is the payload for the request this transmission was requested with. (see 3 byte data bitflags)

Speculative interpretation of ACK byte:

ACK byte
Bit	0	1	2	3	4	5	6	7
Funktion	ACK	UNIMPL	ACK	UNIMPL	0		UNIMPL	0

0xA0 => transmission understood, everything OK
0xF2 => transmission understood, but Feature not implemented

Data bytes:

4 Byte:

Daten
Byte	0								1								2								3
Bit	0	1	2	3	4	5	6	7	0	1	2	3	4	5	6	7	0	1	2	3	4	5	6	7	0	1	2	3	4	5	6	7
Purpose	key												0	value											checksum

3 Byte:

Data
Byte	0								1								2
Bit	0	1	2	3	4	5	6	7	0	1	2	3	4	5	6	7	0	1	2	3	4	5	6	7
Purpose	Command								Bitflags				Set Value				Checksum

Bitflags[2] = apply setting
Bitflags[1] = request special transmission

Features

This table was taken from cmds.csv wich was made by capturing the init sequence of CCU and CAM.
With this handshake all available/unavailable Features should be negotiated.

cmd type

cmd => 3 byte
key => 4 byte

setting

hex value for a specific setting (topic)
must be treated differently for key and cmd

value

value to be set for the setting

bitfield

currently we are thinking these bits represet specific flags
applies only to 3 byte commands; also see the section about 3 byte data

cam response

Response byte sent by the Camera,
tells if the requested feature is available in the specific model.
The following table was created by listening to communication with a JVC GM-HY251 //TODO: camera model?

topic

human readable representation of the setting-id
for example cmd setting 0x07 is understood as gain control

value-representation

human readable representation of the values a setting can have.
such as ON, OFF, incremental values, specific operation modes, ...

cmd type	setting	value	bitfield	cam response	topic	value-representation
cmd	0x00	0x0	0b0100	IMPL	Colorbars

cmd	0x01	0x0	0b0100	IMPL	Detail

cmd	0x02	0x0	0b0100	IMPL	Autoiris
cmd	0x02	0x1	0b0100	IMPL	Autoiris

cmd	0x03	0x0	0b0100	IMPL	White Bal	Manual
cmd	0x03	0x1	0b0100	IMPL	White Bal	Preset
cmd	0x03	0x2	0b0100	IMPL	White Bal	A
cmd	0x03	0x3	0b0100	IMPL	White Bal	B
cmd	0x03	0xf	0b0100	IMPL	White Bal	full auto

cmd	0x06	0x0	0b0110	UNIPLM	Auto White
cmd	0x06	0x1	0b0110	IMPL	Auto White

cmd	0x07	0x0	0b0100	IMPL	Gain	0dB
cmd	0x07	0x1	0b0100	IMPL	Gain	6dB
cmd	0x07	0x2	0b0100	IMPL	Gain	9dB
cmd	0x07	0x3	0b0100	IMPL	Gain	12dB
cmd	0x07	0x4	0b0100	IMPL	Gain	18dB
cmd	0x07	0x5	0b0100	UNIPLM	Gain
cmd	0x07	0x6	0b0100	UNIPLM	Gain
cmd	0x07	0x8	0b0100	IMPL	Gain
cmd	0x07	0x8	0b0100	IMPL	Gain	ALC
cmd	0x07	0xa	0b0100	IMPL	Gain	3dB
cmd	0x07	0xe	0b0100	UNIPLM	Gain

cmd	0x08	0x0	0b0100	IMPL	Tally PGM
cmd	0x08	0x1	0b0100	IMPL	Tally PGM

cmd	0x09	0x0	0b0100	IMPL	Call
cmd	0x09	0x1	0b0100	IMPL	Call

cmd	0x0b	0x0	0b0110	UNIPLM

cmd	0x0c	0x0	0b0100	IMPL	Shutter	off
cmd	0x0c	0x1	0b0100	UNIPLM	Shutter
cmd	0x0c	0x2	0b0100	IMPL	Shutter	1/120
cmd	0x0c	0x3	0b0100	IMPL	Shutter	1/250
cmd	0x0c	0x4	0b0100	IMPL	Shutter	1/500
cmd	0x0c	0x5	0b0100	IMPL	Shutter	1/1000
cmd	0x0c	0x6	0b0100	IMPL	Shutter	1/2000
cmd	0x0c	0xf	0b0100	UNIPLM	Shutter

cmd	0x0f	0x0	0b0100	IMPL	Black Toe	unmod
cmd	0x0f	0x1	0b0100	IMPL	Black Toe	stretch
cmd	0x0f	0x2	0b0100	IMPL	Black Toe	compress

cmd	0x1b	0x0	0b0100	UNIPLM
cmd	0x1b	0x1	0b0100	UNIPLM

cmd	0x1c	0x0	0b0100	IMPL	Auto Knee

cmd	0x1d	0x0	0b0100	IMPL	Gamma
cmd	0x1d	0x1	0b0100	IMPL	Gamma
cmd	0x1d	0x2	0b0100	IMPL	Gamma
cmd	0x1d	0x3	0b0100	IMPL	Gamma
cmd	0x1d	0x4	0b0100	IMPL	Gamma

cmd	0x47	0x0	0b0100	IMPL	GENLOCK SC	0
cmd	0x47	0x1	0b0100	IMPL	GENLOCK SC	90
cmd	0x47	0x2	0b0100	IMPL	GENLOCK SC	180
cmd	0x47	0x3	0b0100	IMPL	GENLOCK SC	270

cmd	0x4a	0x0	0b0100	IMPL	DNR

cmd	0x4b	0x0	0b0100	UNIPLM
cmd	0x4b	0x1	0b0100	UNIPLM
cmd	0x4b	0x2	0b0100	UNIPLM
cmd	0x4b	0xf	0b0100	UNIPLM

cmd	0x4c	0x0	0b0100	IMPL
cmd	0x4c	0x1	0b0100	IMPL
cmd	0x4c	0x2	0b0100	IMPL
cmd	0x4c	0xf	0b0100	UNIPLM

cmd	0x4d	0x0	0b0100	IMPL	Skin Detail

cmd	0x4e	0x1	0b0100	UNIPLM

cmd	0x4f	0x0	0b0100	UNIPLM
cmd	0x4f	0x1	0b0100	UNIPLM
cmd	0x4f	0x2	0b0100	UNIPLM

cmd	0x50	0x1	0b0100	IMPL	Full Auto Shooting

cmd	0x51	0x0	0b0100	UNIPLM
cmd	0x51	0x1	0b0100	UNIPLM

cmd	0x52	0x0	0b0100	IMPL

cmd	0x53	0x0	0b0100	IMPL	Tally PVW
cmd	0x53	0x1	0b0100	IMPL	Tally PVW

cmd	0x7c	0x1	0b0100	IMPL

cmd	0x7d	0x1	0b0100	IMPL

key	0x00	0x340		IMPL	Iris

key	0x02			IMPL	Gain R

key	0x03			IMPL	Gain B

key	0x06			IMPL	Master Black

key	0x12	0x530		UNIPLM

key	0x14	0x400		IMPL

key	0x16	0x400		IMPL

key	0x26	0x328		IMPL	Red
key	0x26	0x404		IMPL	Red

key	0x27	0x230		IMPL	Blue
key	0x27	0x41c		IMPL	Blue

key	0x32	0x604		IMPL

key	0x36	0x114		IMPL	Gamma Master

key	0x37	0x114		IMPL	Gamma G

key	0x40	0x340		IMPL	Autoiris

key	0x56	0x26e		UNIPLM

key	0x74	0x801		UNIPLM

key	0xb4	0x801		UNIPLM	Genlock H Phase 1
key	0xb5	0x801		UNIPLM	Genlock H Phase 2

key	0xf2	0x008		UNIPLM
key	0xf2	0x00c		UNIPLM
key	0xf2	0x80c		UNIPLM

key	0xf3	0x00c		UNIPLM
key	0xf3	0xf7c		UNIPLM

yasdfgr/jvc-remote