This fork - pyLoRa

This fork is an adaptation and an improved version of the original mayeranalytic work (mayeranalytics/pySX127x) pyLoRa can be used to communicate with the Arduino through the RADIOHEAD library, for more information see these examples -> rpsreal/LoRa_Ra-02_Arduino.

Update 05/2018 - Added encrypted versions For security reasons it is advisable to use the encrypted versions that use Advanced Encryption Standard (AES). You can also use them to communicate with the Arduino.

Update 08/2018 - Added support for 2 modules at the same time Now it is possible to use 2 radio modules at the same time in Raspberry Pi. To do this, simply use the BOARD2 settings like this:

# Use BOARD 2 (you can use BOARD1 and BOARD2 at the same time just give another name)
from SX127x.LoRa import LoRa2 as LoRa
from SX127x.board_config import BOARD2 as BOARD

Update 04/2019 - Clarification on the use of different communication frequencies It is possible to use several different communication frequencies using pyLora. The default frequency is 868MHz (Europe), but you can change the communication frequency to use Ai-Thinker Ra-02 Modules (433MHz) for example. To do this, look for the "868" in the SX127x/LoRa.py file and replace them with the desired frequency.

It supports Python 3 or newer and PyPi. https://pypi.org/project/pyLoRa/

Easy setup on Raspberry Pi:

sudo raspi-config nonint do_spi 0
sudo apt-get install python-dev python3-dev

Installation:

For Install with pip perform the following installation steps:

sudo apt-get install python-pip python3-pip
pip install RPi.GPIO
pip install spidev
pip install pyLoRa

For encrypted versions only it is necessary to perform the following installation step:

pip install pycryptodome
pip install pycrypto

Hardware

Make the connections as shown below. If it is necessary to change edit the file board_config.py

Ra-02 LoRa BOARD1	RaspPi GPIO	Ra-02 LoRa BOARD2	RaspPi GPIO
MOSI	GPIO 10	MOSI	GPIO 10
MISO	GPIO 9	MISO	GPIO 9
SCK (SCLK)	GPIO 11	SCK (SCLK)	GPIO 11
NSS	GPIO 8 (CE0)	NSS	GPIO 7 (CE1)
DIO0 (IRQ)	GPIO 4	DIO0 (IRQ)	GPIO 23
DIO1	GPIO 17	DIO1	GPIO 24
DIO2	GPIO 18	DIO2	GPIO 25
DIO3	GPIO 27	DIO3	GPIO 5
RST (Reset)	GPIO 22	RST (Reset)	GPIO 6
LED	GPIO 13	LED	GPIO 19

LED external with 1k ohm or 330ohm (optional)

How to Use

View the sample files. If you downloaded the library and sample files, now you can start LORA_SERVER or LORA_CLIENT (encrypted or non-encripted). To work, there must be another LORA_SERVER or LORA_CLIENT running on another device (Raspberry Pi or Arduino)

For example, if you are running on an Arduino the LORA_CLIENT then start the LORA_SERVER.py on Raspberry Pi like this:

cd pySX127x
python3 ./LORA_SERVER.py

Extra

If you do not need to install the library you can use it simply in the same directory. To Download library and example files:

sudo apt-get install python-rpi.gpio python3-rpi.gpio
sudo apt-get install python-spidev python3-spidev
sudo apt-get install git
sudo git clone https://github.com/rpsreal/pySX127x

If it is necessary to run the library from anywhere:

nano ~/.bashrc

Put this at the end of the file:

export PYTHONPATH=/home/pi/pySX127x/

And then:

source ~/.bashrc

Developed by Rui Silva, Porto, Portugal

Forked from mayeranalytics/pySX127x

Overview

This is a python interface to the Semtech SX1276/7/8/9 long range, low power transceiver family.

The SX127x have both LoRa and FSK capabilities. Here the focus lies on the LoRa spread spectrum modulation hence only the LoRa modem interface is implemented so far (but see the roadmap below for future plans).

Spread spectrum modulation has a number of intriguing features:

High interference immunity
Up to 20dBm link budget advantage (for the SX1276/7/8/9)
High Doppler shift immunity

More information about LoRa can be found on the LoRa Alliance website. Links to some LoRa performance reports can be found in the references section below.

Motivation

Transceiver modules are usually interfaced with microcontroller boards such as the Arduino and there are already many fine C/C++ libraries for the SX127x family available on github and mbed.org.

Although C/C++ is the de facto standard for development on microcontrollers, python running on a Raspberry Pi is becoming a viable alternative for rapid prototyping.

High level programming languages like python require a full-blown OS such as Linux. (There are some exceptions like PyMite and most notably MicroPython.) But using hardware capable of running Linux contradicts, to some extent, the low power specification of the SX127x family. Therefore it is clear that this approach aims mostly at prototyping and technology testing.

Prototyping on a full-blown OS using high level programming languages has several clear advantages:

Working prototypes can be built quickly
Technology testing ist faster
Proof of concept is easier to achieve
The application development phase is reached quicker

Hardware

The transceiver module is a SX1276 based Modtronix inAir9B. It is mounted on a prototyping board to a Raspberry Pi rev 2 model B.

Proto board pin	RaspPi GPIO	Direction
inAir9B DIO0	GPIO 22	IN
inAir9B DIO1	GPIO 23	IN
inAir9B DIO2	GPIO 24	IN
inAir9B DIO3	GPIO 25	IN
inAir9b Reset	GPIO ?	OUT
LED	GPIO 18	OUT
Switch	GPIO 4	IN

Todo:

Add picture(s)
Wire the SX127x reset to a GPIO?

Code Examples

Overview

First import the modules

from SX127x.LoRa import *
from SX127x.board_config import BOARD

then set up the board GPIOs

BOARD.setup()

The LoRa object is instantiated and put into the standby mode

lora = LoRa()
lora.set_mode(MODE.STDBY)

Registers are queried like so:

print lora.get_version()        # this prints the sx127x chip version
print lora.get_freq()       # this prints the frequency setting

and setting registers is easy, too

lora.set_freq(433.0)       # Set the frequency to 433 MHz

In applications the LoRa class should be subclassed while overriding one or more of the callback functions that are invoked on successful RX or TX operations, for example.

class MyLoRa(LoRa):

  def __init__(self, verbose=False):
    super(MyLoRa, self).__init__(verbose)
    # setup registers etc.

  def on_rx_done(self):
    payload = self.read_payload(nocheck=True) 
    # etc.

In the end the resources should be freed properly

BOARD.teardown()

More details

Most functions of SX127x.Lora are setter and getter functions. For example, the setter and getter for the coding rate are demonstrated here

print lora.get_coding_rate()                # print the current coding rate
lora.set_coding_rate(CODING_RATE.CR4_6)     # set it to CR4_6

@todo

Installation

Make sure SPI is activated on you RaspberryPi: SPI pySX127x requires these two python packages:

RPi.GPIO for accessing the GPIOs, it should be already installed on a standard Raspian Linux image
spidev for controlling SPI

In order to install spidev download the source code and run setup.py manually:

wget https://pypi.python.org/packages/source/s/spidev/spidev-3.1.tar.gz
tar xfvz  spidev-3.1.tar.gz
cd spidev-3.1
sudo python setup.py install

At this point you may want to confirm that the unit tests pass. See the section Tests below.

You can now run the scripts. For example dump the registers with lora_util.py:

rasp$ sudo ./lora_util.py
SX127x LoRa registers:
 mode               SLEEP
 freq               434.000000 MHz
 coding_rate        CR4_5
 bw                 BW125
 spreading_factor   128 chips/symb
 implicit_hdr_mode  OFF
 ... and so on ....

Class Reference

The interface to the SX127x LoRa modem is implemented in the class SX127x.LoRa.LoRa. The most important modem configuration parameters are:

Function	Description
set_mode	Change OpMode, use the constants.MODE class
set_freq	Set the frequency
set_bw	Set the bandwidth 7.8kHz ... 500kHz
set_coding_rate	Set the coding rate 4/5, 4/6, 4/7, 4/8

@todo

Most set_* functions have a mirror get_* function, but beware that the getter return types do not necessarily match the setter input types.

Register naming convention

The register addresses are defined in class SX127x.constants.REG and we use a specific naming convention which is best illustrated by a few examples:

Register	Modem	Semtech doc.	pySX127x
0x0E	LoRa	RegFifoTxBaseAddr	REG.LORA.FIFO_TX_BASE_ADDR
0x0E	FSK	RegRssiCOnfig	REG.FSK.RSSI_CONFIG
0x1D	LoRa	RegModemConfig1	REG.LORA.MODEM_CONFIG_1
etc.

Hardware

Hardware related definition and initialisation are located in SX127x.board_config.BOARD. If you use a SBC other than the Raspberry Pi you'll have to adapt the BOARD class.

Script references

Continuous receiver `rx_cont.py`

The SX127x is put in RXCONT mode and continuously waits for transmissions. Upon a successful read the payload and the irq flags are printed to screen.

usage: rx_cont.py [-h] [--ocp OCP] [--sf SF] [--freq FREQ] [--bw BW]
                  [--cr CODING_RATE] [--preamble PREAMBLE]

Continous LoRa receiver

optional arguments:
  -h, --help            show this help message and exit
  --ocp OCP, -c OCP     Over current protection in mA (45 .. 240 mA)
  --sf SF, -s SF        Spreading factor (6...12). Default is 7.
  --freq FREQ, -f FREQ  Frequency
  --bw BW, -b BW        Bandwidth (one of BW7_8 BW10_4 BW15_6 BW20_8 BW31_25
                        BW41_7 BW62_5 BW125 BW250 BW500). Default is BW125.
  --cr CODING_RATE, -r CODING_RATE
                        Coding rate (one of CR4_5 CR4_6 CR4_7 CR4_8). Default
                        is CR4_5.
  --preamble PREAMBLE, -p PREAMBLE
                        Preamble length. Default is 8.

Simple LoRa beacon `tx_beacon.py`

A small payload is transmitted in regular intervals.

usage: tx_beacon.py [-h] [--ocp OCP] [--sf SF] [--freq FREQ] [--bw BW]
                    [--cr CODING_RATE] [--preamble PREAMBLE] [--single]
                    [--wait WAIT]

A simple LoRa beacon

optional arguments:
  -h, --help            show this help message and exit
  --ocp OCP, -c OCP     Over current protection in mA (45 .. 240 mA)
  --sf SF, -s SF        Spreading factor (6...12). Default is 7.
  --freq FREQ, -f FREQ  Frequency
  --bw BW, -b BW        Bandwidth (one of BW7_8 BW10_4 BW15_6 BW20_8 BW31_25
                        BW41_7 BW62_5 BW125 BW250 BW500). Default is BW125.
  --cr CODING_RATE, -r CODING_RATE
                        Coding rate (one of CR4_5 CR4_6 CR4_7 CR4_8). Default
                        is CR4_5.
  --preamble PREAMBLE, -p PREAMBLE
                        Preamble length. Default is 8.
  --single, -S          Single transmission
  --wait WAIT, -w WAIT  Waiting time between transmissions (default is 0s)

Tests

Execute test_lora.py to run a few unit tests.

Contributors

Please feel free to comment, report issues, or contribute!

Contact me via my company website Mayer Analytics and my private blog mcmayer.net.

Follow me on twitter @markuscmayer and @mayeranalytics.

Roadmap

95% of functions for the Sx127x LoRa capabilities are implemented. Functions will be added when necessary. The test coverage is rather low but we intend to change that soon.

Semtech SX1272/3 vs. SX1276/7/8/9

pySX127x is not entirely compatible with the 1272. The 1276 and 1272 chips are different and the interfaces not 100% identical. For example registers 0x26/27. But the pySX127x library should get you pretty far if you use it with care. Here are the two datasheets:

HopeRF transceiver ICs

HopeRF has a family of LoRa capable transceiver chips RFM92/95/96/98 that have identical or almost identical SPI interface as the Semtech SX1276/7/8/9 family.

Microchip transceiver IC

Likewise Microchip has the chip RN2483

The pySX127x project will therefore be renamed to pyLoRa at some point.

LoRaWAN

LoRaWAN is a LPWAN (low power WAN) and, and pySX127x has almost no relationship with LoRaWAN. Here we only deal with the interface into the chip(s) that enable the physical layer of LoRaWAN networks.

References

Hardware references

LoRa performance tests

Spread spectrum modulation theory

An Introduction to Spread Spectrum Techniques
Theory of Spread-Spectrum Communications-A Tutorial (technical paper)

Copyright and License

Short version

The license is GNU AGPL.

Long version

pySX127x is free software: you can redistribute it and/or modify it under the terms of the GNU Affero General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.

pySX127x is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Affero General Public License for more details.

You can be released from the requirements of the license by obtaining a commercial license. Such a license is mandatory as soon as you develop commercial activities involving pySX127x without disclosing the source code of your own applications, or shipping pySX127x with a closed source product.

You should have received a copy of the GNU General Public License along with pySX127. If not, see http://www.gnu.org/licenses/.

yiipi/pySX127x-OpiZero

This fork - pyLoRa

Easy setup on Raspberry Pi:

Installation:

Hardware

How to Use

Extra

Forked from mayeranalytics/pySX127x

Overview

Motivation

Hardware

Code Examples

Overview

More details

Installation

Class Reference

Register naming convention

Hardware

Script references

Continuous receiver rx_cont.py

Simple LoRa beacon tx_beacon.py

Tests

Contributors

Roadmap

Semtech SX1272/3 vs. SX1276/7/8/9

HopeRF transceiver ICs

Microchip transceiver IC

LoRaWAN

References

Hardware references

LoRa performance tests

Spread spectrum modulation theory

Copyright and License

Short version

Long version

Continuous receiver `rx_cont.py`

Simple LoRa beacon `tx_beacon.py`