A repository for compiling modified parts, or a hashtag to be added to tweets about VORON.
Under development: It is a modification of an existing component, but it has never been tested and is "very" experimental. (To be tested soon, but undecided.)
- Rear mounting of electrical components mod for VORON2.4
- din_rail_mount_a/b inspired from SnakeOil-XY
| Part | Qty | Sourcing | Description/Note |
|---|---|---|---|
| din_rail_mount_x2 | 2 | Print part(STEP or STL) | |
| SHCS M3x** | 2 | Local store | Length are TBD. |
| M3 Roll-in T-Nut | 2 | AliExpress | |
| SB2040 Cable-harness or 2-wire 18AWG Robot Cable(3 meter) + 2-wire AWG22 Robot Cable(3 meter) |
1 | AliExpress or Misumi(AWG18) + Misumi(AWG22) |
Length are TBD. See Cable Processing |
| RJ11 Cable | 1 | Misumi | For BTT Octopus only. See Cable Processing |
| Toolhead PCB | 1 | AliExpress | AliExpress's link is example for in Stealthburner. |
| BHCS M5x10 | 2 | Stock or Local store | Replace of screws due to removal of "XY Cable Chain Bridge". |
- Attempt to determine if printed brackets can be used to strengthen rigidity
- model based Misumi's HBLFSN5(2mm narrower to avoid interference with Z_Idler)
| Part | Qty | Sourcing | Description/Note |
|---|---|---|---|
| 2020Frame Corner Bracket 18mmWide | 12 | Print part(STEP or STL) | |
| SHCS M5x10 | 24 | Local store | |
| M5 Roll-in T-Nut | 24 | AliExpress | |
| z_belt_cover_a_x2 | 2 | Print part(STEP or STL) | Use existing screws and nuts for mounting. |
| z_belt_cover_b_x2 | 2 | Print part(STEP or STL) | Use existing screws and nuts for mounting. |
- Endstop PCB utilizing the switch mounting holes on the back side of X_Carriage
| Part | Qty | Sourcing | Description/Note |
|---|---|---|---|
| Endstop PCB | 1 | order PCB yourself(KiCad) or Single item PCB from me | |
| Self-tapping screw M2x12 or M2x14 | 2 | Local store or AliExpress | PCB mount screw |
| D2F-L3-A1 microswitch | 1 | Digikey or Mouser or Local store | X Endstop |
| D2F-L3 microswitch | 1 | Digikey or Mouser or Local store | Y Endstop |
| JST-XH S3B-XH-A | 1 | Digikey or Mouser or Local store | |
| JST XH XHP-3 | 1 | Digikey or Mouser or Local store | Qty is the number used on this PCB only, the number may vary depending on the connection point. |
- Mod to bring "inlet and switch"(PowerUI) to front skirt
- Can divert parts used in existing front_skirt_a and power_inlet_filtered
| Part | Qty | Sourcing | Description/Note |
|---|---|---|---|
| front_skirt_a_mod | 1 | Print part(STEP or STL) | |
| [Optional] power_inlet_filtered_mod | 1 | Print part(STEP or STL) | Optional part. May use original parts. |
- Config for BTT Octopus+Mellow SB2040
- based VORON's config and Mellow/KlipperCN's config
| File | Description/Note |
|---|---|
| printer.cfg | |
| steppers.cfg | XYZ motor drive settings |
| toolhead.cfg | SB2040 settings |
| octopus_heatmanage.cfg | Bed-heater and FAN(excl toolhead fans) control |
| neopixel.cfg | lighting settings in chamber |
| macros.cfg | |
| display.cfg | BTT Mini12864 settings |
Shoiko(背負子) is an Japanese word meaning "backpack". (naming inspired from Kirigami.)
This design are partially derived from the existing Voron parts and hence follow the same License, GNU GPLv3.