PSLab Firmware

This repository contains firmware for the Pocket Science Lab (PSLab) open hardware platform.

Pocket Science Lab

The PSLab provides an array of test and measurement instruments for doing science and engineering experiments. Its built-in instruments include an oscilloscope, a waveform generator, a frequency counter, programmable voltage and current sources, and a logic analyzer. The PSLab also has UART, I2C, and SPI buses, via which external devices can be connected and controlled.

The PSLab is a fully open device, and FOSSASIA provides a complete hardware and software stack under open source licenses:

Buy

You can get a Pocket Science Lab device from the FOSSASIA shop
More resellers are listed on the PSLab website

Get in touch

The PSLab chat channel is on Gitter
Please also join us on the PSLab Mailing List

Dependencies

The following tools are required to build the firmware:

xc16 compiler
cmake

Building

This project is built with CMake. After cloning this repository, you must first initialize and update the toolchain submodule:

git submodule init
git submodule update

This will populate the external/cmake-microchip directory, after which the firmware can be built:

mkdir build
cd build
cmake ..
make

This will create a build artifact in the build directory: pslab-firmware.hex.

Flashing

The firmware can be flashed over USB or by using a programmer such as the PICkit3.

Over USB

Firmware can be flashed over USB if the device already has the bootloader installed.

Flashing the firmware requires the pslab-python library. See pslab-python for installation instructions.

Follow these steps to flash new firmware:

Ground the BOOT pin
Reset or power cycle the device
Run pslab flash --port <portname> firmware.hex
Unground the BOOT pin
Reset or power cycle the device

Using a programmer

Warning
If your device contains a bootloader, flashing just the firmware HEX with a programmer will OVERWRITE the bootloader. If for some reason you are unable to flash over USB, it is a better idea to first create a combined HEX file containing both the bootloader and the firmware and flash that, rather than flashing the pure firmare HEX. See the bootloader repository for instructions on how to create a combined HEX.

Flashing with a programmer requires the mdb.sh script, which is distributed as part of Microchip's MPLAB-X software suite. On Linux, the default installation path for mdb.sh is /opt/microchip/mplabx/<version>/mplab_platform/bin/mdb.sh. This script is used to run the file flash.mdbscript, located in the repository root. Before following the below steps, you may need to modify flash.mdbscript depending on which programmer you are using and the location of the firmware HEX.

Disconnect the device from any power source
Connect the programmer to the device's ICSP header
Power on the device via USB
Run mdb.sh flash.mdbscript
Disconnect the programmer

Repository structure

📦pslab-firmware
 ┣ 📂src                        # PSLab firmware source code
 ┃ ┣ 📂bus                      # Communication specific source files
 ┃ ┃ ┣ 📜 ...
 ┃ ┃ ┗ 📜i2c.c
 ┃ ┣ 📂helpers                  # Supplementary functions
 ┃ ┃ ┣ 📜 ...
 ┃ ┃ ┗ 📜version.c
 ┃ ┣ 📂instruments              # Instrument specific source files
 ┃ ┃ ┣ 📜 ...
 ┃ ┃ ┗ 📜multimeter.c
 ┃ ┣ 📂registers                # PIC specific register entry files
 ┃ ┃ ┣ 📂comparators
 ┃ ┃ ┃ ┣ 📜 ...
 ┃ ┃ ┃ ┗ 📜ic1.c
 ┃ ┃ ┣ 📂 ...                   # includes converters, memory, system
 ┃ ┃ ┣ 📂timers
 ┃ ┃ ┃ ┣ 📜 ...
 ┃ ┃ ┃ ┗ 📜tmr1.c
 ┃ ┣ 📂sdcard                   # SD Card specific file handling source files
 ┃ ┣ 📜 ...
 ┃ ┣ 📜main.c                   # Entry point to PSLab Core
 ┃ ┣ 📜commands.c               # Entry point to function implementations
 ┣ 📂external
 ┃ ┣ 📂cmake-microchip          # Toolchain submodule
 ┣ 📜CMakeLists.txt
 ┣ 📜flash.mdbscript
 ┣ 📜LICENSE
 ┗ 📜README.md

zsdshuai/pslab-firmware