CAP1Sup/Intellistep

Issues

• is this repository still maintained?

  #127 opened 10 months ago by wildblue
  1

• can't get the F* crc works.... need help

  #126 opened 2 years ago by jlmxyz
  15

• A4950 / Stepping Interface Questions

  #125 opened 2 years ago by jlmxyz
  6

• CERN-OHL-S hardware license

  #124 opened 2 years ago by dzid26
  3

• HAlL_GetTick() returns 0, causing endless loop

  #122 opened 3 years ago by jlmxyz
  1

• S42B, S57B schematic

  #22 opened 4 years ago by IhorNehrutsa
  24

• Runaway after switching rotation direction

  #118 opened 3 years ago by rob-mcinerney
  10

• Set up menu sequence - help

  #119 opened 3 years ago by rob-mcinerney
  7

• If disable CAN then encoder is blocked

  #77 opened 3 years ago by IhorNehrutsa
  4

• Minor missed counts using the hardware step counter

  #111 opened 3 years ago by CAP1Sup
  16

• OLED and Motor Lock Up after Temperature Increase

  #113 opened 3 years ago by rob-mcinerney
  14

• Motor not disabling without `STEP_CORRECTION`

  #112 opened 3 years ago by CAP1Sup
  2

• Encoder (TLE5012) Improvements

  #59 opened 3 years ago by IhorNehrutsa
  15

• Incorrect Error Measurement

  #108 opened 3 years ago by CAP1Sup
  14

• Readiness state?

  #110 opened 3 years ago by arrowcircle
  2

• Microsteps set through LCD forgotten after the reset

  #91 opened 3 years ago by IhorNehrutsa
  5

• Possible “salmon skin” issue

  #109 opened 3 years ago by CAP1Sup
  0

• PID M-codes

  #86 opened 3 years ago by IhorNehrutsa
  3

• Compilation Error in main.cpp

  #104 opened 3 years ago by jlmxyz
  12

• Incorrect saving of the configuration to memory

  #107 opened 3 years ago by svsergo
  10

• Info: BT LED error indicator turns on at +/- 35 degrees

  #100 opened 3 years ago by IhorNehrutsa
  2

• Driver speed

  #31 opened 4 years ago by IhorNehrutsa
  41

• Measure frequency(period) of input step pulses

  #95 opened 3 years ago by IhorNehrutsa
  2

• Bug in StepperMotor::getHardStepCNT()

  #92 opened 3 years ago by IhorNehrutsa
  3

• COUNTER_CLOCKWISE

  #85 opened 3 years ago by IhorNehrutsa
  2

• StepperMotor::currentAngle is only calculated, but never used

  #80 opened 3 years ago by IhorNehrutsa
  2

• StepperMotor::desiredAngle is only calculated, but never used

  #81 opened 3 years ago by IhorNehrutsa
  3

• Revert variable name 'softStepCNT' to 'desiredStep'

  #79 opened 3 years ago by IhorNehrutsa
  15

• Possible Missed Steps

  #56 opened 3 years ago by CAP1Sup
  18

• Some findings regarding Klipper

  #6 opened 4 years ago by TazerReloaded
  13

• A4950 PWM frequency

  #39 opened 4 years ago by IhorNehrutsa
  2

• PID + PID Tuning Utility

  #35 opened 4 years ago by IhorNehrutsa
  9

• Calibration required to start stepper but can't calibrate

  #30 opened 4 years ago by jubjub64
  5

• Microstep multiplier

  #46 opened 4 years ago by IhorNehrutsa
  2

• It was uint32_t before

  #41 opened 4 years ago by IhorNehrutsa
  4

• Legacy code

  #33 opened 4 years ago by IhorNehrutsa
  1

• S42B doesn't reverse at endstop switch

  #25 opened 4 years ago by jubjub64
  6

• Question on "Precompiled" files

  #16 opened 4 years ago by jubjub64
  2

• flashes, reads "Oled Init... OK:" and no operation

  #11 opened 4 years ago by RocksaltX
  4

• xerootg Help

  #4 opened 4 years ago by xerootg
  17

• Serial Communication is not functioning

  #2 opened 4 years ago by GhostlyCrowd
  51

• Discussion: Observations so far on Pull 16e78cf

  #1 opened 4 years ago by GhostlyCrowd
  1

• Serial issue (#2)

  #5 opened 4 years ago by CAP1Sup
  0