OpenROV/openrov-electronics

Issues

• Bill of Materials link is dead

  #42 opened 6 months ago by EngineeringOV
  0

• remove special characters from directory name.

  #40 opened 7 years ago by Madouc
  0

• IMU

  #39 opened 7 years ago by briangrau
  0

• Change LED to non obsolete parts on 2.8 CB

  #38 opened 7 years ago by briangrau
  0

• 2.8 CB Obsolete Part

  #37 opened 7 years ago by briangrau
  0

• 2.8 CB Q1

  #36 opened 7 years ago by briangrau
  0

• Topside interface board: Expose 5V power and GND as solder points

  #35 opened 8 years ago by codewithpassion
  0

• Add Polyfuse Protection to Controller Board Tester

  #34 opened 9 years ago by briangrau
  0

• Change LEDs on Topside Adapter

  #33 opened 9 years ago by briangrau
  0

• Increase Copper Cuttout Hole on 2.8 Light Board

  #31 opened 9 years ago by briangrau
  3

• Some 2.8 Controller boards failing QA at higher than desired rates on QA step 18

  #30 opened 9 years ago by BrianAdams
  1

• 2.7 part out of production: Voltage Regulator for I2C needs to be replaced

  #29 opened 9 years ago by BrianAdams
  1

• Improve filtering on current measurement telemetry points

  #27 opened 9 years ago by BrianAdams
  2

• Move external power input to board periphery

  #26 opened 9 years ago by BrianAdams
  1

• Enable external LED capability to the board

  #23 opened 9 years ago by BrianAdams
  1

• Fix ramp of the 3.3V power supply

  #22 opened 9 years ago by BrianAdams
  1

• Make the eeprom write protect by default

  #21 opened 9 years ago by BrianAdams
  1

• Add write mode pads to eeprom for controllerboard

  #20 opened 9 years ago by BrianAdams
  1

• Need a way to detect loss of power before the capacitors finish discharging

  #19 opened 9 years ago by BrianAdams
  3

• Humidity sensor pads need to be fixed

  #17 opened 9 years ago by BrianAdams
  1

• Arduino needs to be able to power cycle the I2C power line

  #15 opened 9 years ago by BrianAdams
  1

• BBB does not always start

  #32 opened 9 years ago by BrianAdams
  3

• Explicitly declare every IO line so it is in a known state

  #28 opened 9 years ago by BrianAdams
  1

• Expose ESC power pin

  #25 opened 10 years ago by BrianAdams
  0

• Ability to track PWM current

  #24 opened 10 years ago by BrianAdams
  0

• It would be nice to connect the serial hardware control flow lines for higher speed

  #16 opened 10 years ago by BrianAdams
  0

• Free up the JTAG pins on the controllerboard

  #14 opened 10 years ago by BrianAdams
  0

• Use Aux1 and Aux2 with other voltage sources

  #5 opened 10 years ago by ThomasSo
  5

• Connector - Power Supply

  #3 opened 10 years ago by davidtlang
  2

• No Clearance for Aux 2 Connector

  #4 opened 10 years ago by davidtlang
  3

• Expand I2C Header (P4) on Cape

  #8 opened 10 years ago by WaltHolm
  0

• Gold vs. Tin pins on servo header pins

  #7 opened 10 years ago by WaltHolm
  0

• Servo jumper on Cape in place while ESCs are plugged in should not damage anything

  #9 opened 10 years ago by estackpole
  7

• put a polyfuse on the 3.3 V supply

  #13 opened 10 years ago by BrianAdams
  1

• The USB pins on the Topside Interface Board should be exposed

  #18 opened 10 years ago by codewithpassion
  0

• Schematic drawn wrong

  #1 opened 12 years ago by bransorem
  1