Peter-van-Tol/LiteX-CNC

Issues

• [Feature request]: Revamp Watchdog

  #119 opened 2 months ago by Peter-van-Tol
  28

• Installation on PC does not detect correct platform

  #78 opened 2 months ago by Peter-van-Tol
  2

• [Feature request]: add `index-enable` to STEPGEN

  #111 opened 4 months ago by Peter-van-Tol
  1

• [Feature request]: Support ENCODER counter-mode

  #110 opened 4 months ago by Peter-van-Tol
  0

• [Bug]: Encoder readings wrong

  #120 opened 2 months ago by marland4a
  3

• [Feature request]: Support user LED and button

  #117 opened 2 months ago by Peter-van-Tol
  8

• [Feature request]: Add vexriscv

  #114 opened 3 months ago by romanetz
  3

• [Feature request]: Dither PWM

  #108 opened 5 months ago by Peter-van-Tol
  0

• [Feature request]: Add PWM/direction and UP/DOWN to PWM

  #104 opened 6 months ago by Peter-van-Tol
  4

• Litex-cnc on standalone fpga chip?

  #96 opened 6 months ago by spacehitchhiker42
  0

• Maximum frequency 375 kHz.

  #87 opened a year ago by lex27087
  37

• differential step

  #92 opened a year ago by lex27087
  1

• Upgrade toolchain: bring Yosys to version 0.38

  #88 opened a year ago by Peter-van-Tol
  0

• Add option invert PWM output

  #76 opened a year ago by Peter-van-Tol
  3

• Module: STEPGEN. Timing parameters issue.

  #59 opened a year ago by GTCLive
  17

• New module `shift_in` and `shift_out` for using shift registers

  #86 opened a year ago by Peter-van-Tol
  1

• Stepgen only working up to 4 steppers

  #79 opened a year ago by Peter-van-Tol
  2

• Reset watchdog on FPGA reset

  #80 opened a year ago by Peter-van-Tol
  0

• Requirement for encoder.<n>.reset (HAL_BIT)

  #73 opened a year ago by GTCLive
  17

• Module ENCODER: width of Z-index pulse not taken into account

  #75 opened a year ago by Peter-van-Tol
  0

• PATH not set on LinuxCNC RPi4 image after installing LitexCNC

  #74 opened a year ago by Peter-van-Tol
  2

• GPIO does not compile when either all pins are input or output

  #70 opened a year ago by Peter-van-Tol
  0

• HUB75HAT Pin-out incorrect

  #68 opened a year ago by Peter-van-Tol
  0

• Safety: Upcoming change in Watchdog

  #65 opened a year ago by Peter-van-Tol
  1

• Bugfix for RPI5 Support

  #64 opened a year ago by Peter-van-Tol
  0

• Installation Documentation Update for Debian 12 & Python 3.11 with venv.

  #53 opened a year ago by GTCLive
  14

• Install OpenOCD and flash firmware using Litexcnc-commands

  #55 opened a year ago by Peter-van-Tol
  0

• Support SPI

  #48 opened a year ago by Peter-van-Tol
  1

• Install_litex throws errors when switch --user is not used

  #47 opened a year ago by Peter-van-Tol
  1

• Encoder velocity calculation

  #50 opened a year ago by Peter-van-Tol
  5

• Buffer overflow

  #44 opened a year ago by Peter-van-Tol
  0

• New litexcnc connections="eth:...." problem

  #39 opened a year ago by Peter-van-Tol
  0

• LinuxCNC crashes on exit when component `litexcnc_eth` is used

  #32 opened a year ago by Peter-van-Tol
  11

• Sample stuff for testing

  #24 opened a year ago by ozzyrob
  2

• Add (external) extensions to LitexCNC

  #11 opened a year ago by Peter-van-Tol
  0

• starting LinuxCNC fails with new driver

  #28 opened a year ago by OJthe123
  49

• Default state of output pins

  #29 opened a year ago by OJthe123
  12

• Rewite to Add files via upload (PR #25)

  #26 opened a year ago by ozzyrob
  2

• Velocity is inverted

  #21 opened a year ago by romanetz
  9

• pip install does not work on debian 10, works on arch linux?

  #12 opened a year ago by cdwijs
  3

• Linuxcnc installation: Run In Place vs Nn Run In Place: Litex 11-add-external-extensions-to-litexcnc

  #23 opened a year ago by ozzyrob
  5

• 11-add-external-extensions-to-linuxcnc litexcnc.c

  #22 opened a year ago by ozzyrob
  4

• Install toolchain installs wrong binaries on RPi4

  #20 opened 2 years ago by Peter-van-Tol
  1

• Pin does not exist

  #16 opened 2 years ago by tuxcnc
  20

• New cofig and test files.

  #19 opened 2 years ago by tuxcnc
  3

• RV901T how to ?

  #14 opened 2 years ago by tuxcnc
  6

• Differential outputs

  #17 opened 2 years ago by tuxcnc
  9

• install_driver error

  #15 opened 2 years ago by OJthe123
  3

• pip3 install gives error 404

  #13 opened 2 years ago by dixi83
  4

• Compiles, but does not work with LinuxCNC version 2.9

  #8 opened 2 years ago by Peter-van-Tol
  1