This package is intended to be used as a standard pad for all Robotnik robots.
The package depends on some Robotnik packages:
- rcomponent 🔗
git clone https://github.com/RobotnikAutomation/rcomponent
- robotnik_msgs 🔗
git clone https://github.com/RobotnikAutomation/robotnik_msgs
This package may depend on other Robotnik or ROS standard packages in function of the handlers that are developed. The standard ROS packages can be installed using the rosdep install command:
# located in the workspace folder
rosdep install --from-path src --ignore-src -y -r
The robotnik_pad_node
loads plugins that specify the desired behaviour. This allows you to load different plugins depending on your needs. Besides, it is possible to create your own plugins.
Available plugins:
- Movement
- Intended to command the mobile base via velocity references
- Elevator
- Intended to command a elevator actuator of the robot
- ~pad/type (string, default: ps4) Type/model of the gamepad used
- ~pad/num_of_buttons (int, default: 14) Number of buttons of the gamepad
- ~pad/num_of_axes (int, default: 4) Number of axes of the gamepad
- ~plugins (list of strings, default: [Movement]) Declares the available plugins to use
- ~Plugin/type (string, default: depends on the plugin) Type of plugin
- ~max_linear_speed (double, default: 1.5) Maximum linear speed that can be sent to the controller based on the current velocity level (0.1->1) and the current axis_linear_x value (0->1)
- ~max_angular_speed (double, default: 3.0) Maximum angular speed that can be sent to the controller based on the current velocity level (0.1->1) and the current axis_linear_x value (0->1)
- ~cmd_topic_vel (string, default: cmd_vel) Name of topic where the command vel is being published
- ~config/button_deadman (int, default: 5) Button number to enable any command sent to the controller.
- ~config/button_speed_up (int, default: 3) Button number to increase the current velocity level applied to the max_speed params
- ~config/button_speed_down (int, default: 1) Button number to decrease the current velocity level applied to the max_speed params
- ~config/button_kinematic_mode (int, default: 7) Button number to switch between two kinematic modes: diff and omni
- ~config/axis_linear_x (int, default: 1) Axis number to set the linear x speed
- ~config/axis_linear_y (int, default: 0) Axis number to set the linear y speed
- ~config/axis_angular_z (int, default: 2) Axis number to set the angular speed
This an example of a config file loading a single plugin:
plugins:
- Movement
pad:
type: ps4
num_of_buttons: 14
num_of_axes: 14
Movement:
type: robotnik_pad_plugins/Movement
max_linear_speed: 1.5
max_angular_speed: 3.0
cmd_topic_vel: pad_teleop/cmd_vel
config:
button_deadman: 5
axis_linear_x: 1
axis_linear_y: 0
axis_angular_z: 2
button_speed_up: 3
button_speed_down: 1
button_kinematic_mode: 7
First of all you need to define a list containing the different plugins you want to load. Then, for each of the plugins you want to load, you should specify its parameters.
- joy (sensor_msgs/Joy) Gets the buttons and axis status
- cmd_topic_vel (geometry_msgs/Twist) Sends the velocity references to define topic
- ~state (robotnik_msgs/State) Sends current state based on Robotnik RComponent architecture
- ~status (robotnik_pad_msgs/MovementStatus)
Status of the component
- Example:
velocity_level: 100.0 kinematic_mode: "omni"
- Example:
None
None
None
None
None
None
roslaunch robotnik_pad robotnik_pad.launch
This will launch two nodes:
- joy: This node is in charge of reading from the joystick and publish the information (sensor_msgs/Joy) through a topic
- robotnik_pad_node: This node will load the different plugins included in the config file